Slide rails with fixing bolts and tensioning screws to DIN 42923
Slide rails are used to tension the belt of a machine easily and conveniently when a belt tightener is not available. They are fixed to the base using stone bolts or foundation blocks.
The assignment of slide rails to motor size can be found in DIN 42923. For motors of frame sizes 355 to 450, there are no standardized slide rails (please enquire).
Available from:
Lutgert & Co. GmbH
Postfach 42 51
33276 Gutersloh, Germany
Tel. +49 (0)5241-74 07-0
Fax +49 (0)5241-74 07-90
http://www.luetgert-antriebe.de
e-mail:http://info@luetgert-antriebe.de
Foundation block acc. to DIN 799
The foundation blocks are inserted into the stone foundation and embedded in concrete. They are used for fixing machines of medium size, slide rails, pedestal bearings, base frames, etc. After the fixing bolts have been unscrewed, the machine can be dragged without it having to be lifted.
When the machine is initially installed, the foundation block that is bolted to the machine (without washers) and fitted with taper pins is not embedded with concrete until the machine has been fully aligned. In this case, the machine is positioned 2 to 3 mm lower. The difference in shaft height is compensated by inserting shims on final installation. The taper pins safeguard the exact position of the machine when it is repeatedly removed and replaced without the need for realignment.
Available from:
Lutgert & Co. GmbH
Postfach 42 51
33276 Gutersloh, Germany
Tel. +49 (0)5241-74 07-0
Fax +49 (0)5241-74 07-90
http://www.luetgert-antriebe.de
e-mail:http://info@luetgert-antriebe.de
Taper pins to DIN 258 with threaded ends and constant taper lengths
Taper pins are used for components that are repeatedly removed. The drilled hole is ground conical using a conical reamer until the pin can be pushed in by hand until the cone shoulder lies 3 to 4 mm above the rim of the hole.
It can then be driven in using a hammer until it is correctly seated. The pin is removed from the drilled hole by screwing on the nut and tightening it.
Standardized taper pins are available from general engineering suppliers.
Available from:
Otto Roth GmbH & Co. KG
Rutesheimer Stra?e 22
70499 Stuttgart, Germany
Tel. +49 (0)711-13880
Fax. +49 (0)711-1388233
http://www.ottoroth.de
e-mail:http://info@ottoroth.de
Couplings
In most cases, the motor is connected to the driving machine through coupling.
Available from:
A. Friedr. Flender AG
Kupplungswerk Mussum
Industriepark Bocholt
Schlavenhorst 100
46395 Bocholt, Germany
Tel. +49 (0)2871-92 2185
Fax +49 (0)2871-92 2579
http://www.flender.com
e-mail:http://couplings@flender.com
Mounting of encoder
In the case of mounting by the customer.
Options H79, H80
Baumer Hubner GmbH
10967 Berlin; Germany
Planufer 92b
Tel. +49 (0)30-69003-0
Fax +49 (0)30-69003-104
http://www.baumerhuebner.com
e-mail:http://info@baumerhuebner.com
Options H78
Leine & Linde (Deutschland) GmbH
73430 Aalen, Germany
Bahnhofstra?e 36
Tel. +49 (0)7361-78093-0
Fax +49 (0)7361-78093-11
http://www.leinelinde.de
e-mail:http://info@leinelinde.de
Приводная техника