SIPLUS ET 200S digital electronic modules . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS ET 200S digital electronic modules

| | | |

Article number	6AG1131-4BD01-2AA0	6AG1131-4BD01-7AB0	6AG1131-4BF00-7AA0	6AG1131-4BF50-7AA0
	SIPLUS DP 4DI ET200S	SIPLUS ET200S EM 4 DI high features	SIPLUS ET200S EM 8 DI	SIPLUS ET200S EM 8 DI DC24V
Supply voltage
Rated value (DC)
в—Џ 24 V DC	Yes; From power module	Yes; From power module	Yes	Yes; From power module
Reverse polarity protection	Yes	Yes	Yes	Yes
Input current
from supply voltage L+, max.	Dependent on encoder	Dependent on encoder	Dependent on encoder	Dependent on encoder
from backplane bus 3.3 V DC, max.	10 mA	10 mA	10 mA
Encoder supply
Number of outputs			0; no encoder supply
Type of output voltage	min. L+ (-0.5 V), under load	min. L+ (-0.5 V), under load
Short-circuit protection		Yes; Electronic
Output current
в—Џ Rated value	500 mA	500 mA
в—Џ permissible range, lower limit	0 mA	0 mA
в—Џ permissible range, upper limit	500 mA	500 mA
Power loss
Power loss, typ.	0.7 W	0.7 W	1.2 W	1.2 W
Address space per module
в—Џ with packing	4 bit	4 bit
в—Џ without packing	1 byte	1 byte	1 byte
Digital inputs
Number of digital inputs	4	4	8	8
Input characteristic curve in accordance with IEC 61131, type 1	Yes	Yes	Yes; 2-wire sensors connectable	Yes
Number of simultaneously controllable inputs
в—Џ Number of simultaneously controllable inputs			8
Input voltage
в—Џ Type of input voltage	DC	DC	DC	DC
в—Џ Rated value (DC)	24 V	24 V	24 V	24 V
в—Џ for signal "0"	-30 to +5V	-30 to +5V	-30 to +5V	-5 to +30V
в—Џ for signal "1"	+15 to +30V	+11 to +30V	+15 to +30V	-15 to -30 V
Input current
в—Џ for signal "1", typ.	7 mA; at 24 V	8 mA	5 mA	6 mA; at 24 V
Input delay (for rated value of input voltage)
for standard inputs
вЂ” parameterizable	No	Yes; 0.1 / 0.5 / 3 / 15 ms	No	No
вЂ” at "0" to "1", min.	2 ms; typically 3 ms	0.05 / 0.4 / 2.7 / 14.85	2 ms	2 ms
вЂ” at "0" to "1", max.	4.5 ms	0,15 / 0,6 / 3,3 / 15,15	4.5 ms	4.5 ms
вЂ” at "1" to "0", min.	2 ms; typically 3 ms	0.05 / 0.4 / 2.7 / 14.85	2 ms	2 ms
вЂ” at "1" to "0", max.	4.5 ms	0,15 / 0,6 / 3,3 / 15,15	4.5 ms	4.5 ms
Cable length
в—Џ shielded, max.	1 000 m	1 000 m	1 000 m	1 000 m
в—Џ unshielded, max.	600 m	600 m	600 m	600 m
Encoder
Connectable encoders
в—Џ 2-wire sensor	Yes	Yes	Yes	Yes
вЂ” permissible quiescent current (2-wire sensor), max.	1.5 mA	1.5 mA	1.5 mA	1.5 mA
Isochronous mode
Isochronous operation (application synchronized up to terminal)			Yes; TWE = 3000 us	Yes
Interrupts/diagnostics/status information
Diagnostic functions	No	Yes	No	No
Diagnostic messages
в—Џ Short-circuit		Yes; Short-circuit of outputs to ground; module by module
Diagnostics indication LED
в—Џ Group error SF (red)	No	Yes		No
в—Џ Status indicator digital input (green)	Yes; per channel	Yes; per channel	Yes	Yes; per channel
Parameter
Remark	1 byte	3 byte	3-byte parameter (not accessible for the user)	3 byte
Diagnostics short-circuit		Disable / enable
Potential separation
Potential separation digital inputs
в—Џ between the channels	No	No	No	No
в—Џ between the channels and backplane bus	Yes	Yes	Yes	Yes
Permissible potential difference
between different circuits	75 V DC/60 V AC	75 V DC/60 V AC	75 V DC/60 V AC	75 V DC/60 V AC
Isolation
Isolation tested with	500 V DC	500 V DC	500 V DC	500 V DC
Standards, approvals, certificates
CE mark	Yes	Yes	Yes	Yes
Ambient conditions
Ambient temperature during operation
в—Џ min.	-25 °C; = Tmin	-25 °C; = Tmin	-25 °C; = Tmin	-40 °C; = Tmin
в—Џ max.	60 °C; = Tmax	70 °C; = Tmax	70 °C; = Tmax	70 °C; = Tmax
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.	100 %; RH incl. condensation/frost permitted (no commissioning in bedewed state)	100 %; RH incl. condensation/frost permitted (no commissioning in bedewed state)	100 %; incl. condensation / frost permitted (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost permitted (no commissioning in bedewed state)
Resistance
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation in corrosive atmospheres!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3	Yes; Class 3C4 incl. salt spray. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width	15 mm	15 mm	15 mm	15 mm
Height	81 mm	81 mm	81 mm	81 mm
Depth	52 mm	52 mm	52 mm	52 mm
Weights
Weight, approx.	35 g	35 g	35 g	35 g

Article number	6AG1132-4BB01-2AB0	6AG1132-4BB31-7AB0	6AG1132-4BD02-7AA0	6AG1132-4BD32-2AA0
	SIPLUS DP 2DO HF ET200S	SIPLUS ET200S 2DO high feature	SIPLUS ET200S 4DO (1VE = 5 Stueck)	SIPLUS_ET200S_4DO DC24V/2A
Supply voltage
Reverse voltage protection	Yes; when using the same load voltage as on the power module	Yes; when using the same load voltage as on the power module	Yes; when using the same load voltage as on the power module	Yes; when using the same load voltage as on the power module
Load voltage L+
в—Џ Rated value (DC)	24 V; From power module	24 V; From power module	24 V; From power module	24 V; From power module
в—Џ Reverse polarity protection	Yes; polarity reversal can lead to the digital outputs being connected through	Yes; polarity reversal can lead to the digital outputs being connected through	Yes; polarity reversal can lead to the digital outputs being connected through	Yes
Input current
from load voltage L+ (without load), max.	5 mA; Per channel	5 mA; Per channel	10 mA; Per channel	10 mA; Per channel
from backplane bus 3.3 V DC, max.	10 mA	10 mA	10 mA	10 mA
Power loss
Power loss, typ.	0.4 W	1.4 W	0.8 W	1.6 W
Address area
Address space per module
в—Џ with packing	2 bit	2 bit	4 bit	4 bit
в—Џ without packing	1 byte	1 byte	1 byte	1 byte
Digital outputs
Number of digital outputs	2	2	4	4
Short-circuit protection	Yes	Yes	Yes	Yes
в—Џ Response threshold, typ.	1.5 A	4 A	1 to 1.5 A	2.8 to 7.2 A
Limitation of inductive shutdown voltage to	-55 to -60 V, typ. L+( )	-55 to -60 V, typ. L+( )		Typ. L+ (-55 to -60 V)
Controlling a digital input	Yes	Yes	Yes	Yes
Switching capacity of the outputs
в—Џ on lamp load, max.	2.5 W	5 W	5 W	10 W
Load resistance range
в—Џ lower limit	48 в„¦	12 в„¦	48 в„¦	12 в„¦
в—Џ upper limit	3 400 в„¦	3 400 в„¦	3 400 в„¦	3 400 в„¦
Output voltage
в—Џ for signal "1", min.	L+ (-1 V)	L+ (-1 V)	L+ (-1 V)	L+ (-1.0 V)
Output current
в—Џ for signal "1" rated value	0.5 A	2 A	0.5 A	2 A
в—Џ for signal "1" permissible range, min.	7 mA	7 mA	7 mA	7 mA
в—Џ for signal "1" permissible range, max.	600 mA	2.4 A	600 mA	2.4 A
в—Џ for signal "0" residual current, max.	0.3 mA	0.5 mA	0.3 mA	0.5 mA
Output delay with resistive load
в—Џ "0" to "1", max.	100 µs	100 µs	45 µs; Typical value	50 µs; Typ. 45 µs
в—Џ "1" to "0", max.	400 µs	400 µs	90 µs; Typical value	120 µs; Typ. 90 µs
Parallel switching of two outputs
в—Џ for uprating	No	No	No	No
в—Џ for redundant control of a load	Yes; per module	Yes; per module	Yes; per module	Yes; per module
Switching frequency
в—Џ with resistive load, max.	100 Hz	100 Hz	800 Hz	1 000 Hz
в—Џ with inductive load, max.	2 Hz	2 Hz; 0,5 H	2 Hz	2 Hz; At 0.5 H
в—Џ on lamp load, max.	10 Hz	10 Hz	10 Hz	10 Hz
Total current of the outputs
в—Џ Current per module, max.	1 A	4 A	2 A	4 A
Cable length
в—Џ shielded, max.	1 000 m	1 000 m	1 000 m	1 000 m
в—Џ unshielded, max.	600 m	600 m	600 m	600 m
Isochronous mode
Isochronous operation (application synchronized up to terminal)	Yes	Yes	Yes	Yes
Interrupts/diagnostics/status information
Diagnostic functions	Yes; Can be read out	Yes; Can be read out	No	No
Substitute values connectable	Yes; 0/1	Yes; 0/1
Diagnostic messages
в—Џ Wire-break	Yes; channel by channel	Yes; channel by channel
в—Џ Short-circuit	Yes; channel by channel	Yes; channel by channel
Diagnostics indication LED
в—Џ Group error SF (red)	Yes	Yes
в—Џ Status indicator digital output (green)	Yes	Yes	Yes	Yes
Parameter
Remark	3 byte	3 byte	1 byte	1 byte
Diagnostics wire break	Disable / enable	Disable / enable
Diagnostics short-circuit	Disable / enable	Disable / enable
Response to CPU/master STOP	Substitute a value/keep last value	Substitute a value/keep last value
Potential separation
Potential separation digital outputs
в—Џ between the channels	No	No	No	No
в—Џ between the channels and backplane bus	Yes	Yes	Yes	Yes
Isolation
Isolation tested with	500 V DC	500 V DC	500 V DC	500 V DC
Ambient conditions
Ambient temperature during operation
в—Џ min.	-25 °C; = Tmin	-25 °C; = Tmin	-25 °C; = Tmin	-25 °C; = Tmin
в—Џ max.	60 °C; = Tmax	70 °C; = Tmax	70 °C; = Tmax	60 °C; = Tmax
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width	15 mm	15 mm	15 mm	15 mm
Height	81 mm	81 mm	81 mm	81 mm
Depth	52 mm	52 mm	52 mm	52 mm
Weights
Weight, approx.	40 g	40 g	40 g	40 g

Article number	6AG1132-4BF00-7AA0	6AG1132-4BF50-7AA0	6AG1132-4HB12-2AB0
	SIPLUS ET200S EM 8 DO	SIPLUS ET200S EM 8 DO DC24V/0.5A	SIPLUS ET200S 2DORLY 24-48VDC 230VAC/5A
Supply voltage
Reverse voltage protection	Yes	Yes; when using the same correctly polarized load voltage as on the power module
Load voltage L+
в—Џ Rated value (DC)	24 V	24 V; From power module	24 V; From power module
в—Џ Reverse polarity protection	Yes	Yes	Yes
Input current
from load voltage L+ (without load), max.	5 mA; Per channel	5 mA	30 mA
from backplane bus 3.3 V DC, max.	10 mA	10 mA	10 mA
Power loss
Power loss, typ.	1.5 W	1.5 W	0.6 W
Address area
Address space per module
в—Џ with packing			2 bit
в—Џ without packing	1 byte	1 byte	1 byte
Digital outputs
Number of digital outputs	8	8	2
Short-circuit protection	Yes	Yes	No
в—Џ Response threshold, typ.	1.5 A	1.5 A
Limitation of inductive shutdown voltage to	Typ. L+ (-55 to -60 V)	Typ. 47 V	No
Controlling a digital input	Yes	Yes	Yes
Switching capacity of the outputs
в—Џ on lamp load, max.	5 W	5 W
Load resistance range
в—Џ lower limit	48 в„¦	48 в„¦
в—Џ upper limit	3 400 в„¦	3 400 в„¦
Output voltage
в—Џ for signal "1", min.	L+ (-1.0 V)	Max. 1 V
Output current
в—Џ for signal "1" rated value	0.5 A	0.5 A	5 A
в—Џ for signal "1" permissible range, min.	7 mA	5 mA
в—Џ for signal "1" permissible range, max.	600 mA	600 mA
в—Џ for signal "1" minimum load current			8 mA
в—Џ for signal "0" residual current, max.	0.3 mA	5 µA
Output delay with resistive load
в—Џ "0" to "1", max.	300 µs	300 µs
в—Џ "1" to "0", max.	600 µs	600 µs
Parallel switching of two outputs
в—Џ for uprating	No	No
в—Џ for redundant control of a load	Yes	Yes; per module
Switching frequency
в—Џ with resistive load, max.	100 Hz	100 Hz	2 Hz
в—Џ with inductive load, max.	2 Hz	0.5 Hz	0.5 Hz
в—Џ on lamp load, max.	10 Hz	10 Hz	2 Hz
Total current of the outputs
в—Џ Current per module, max.	4 A	4 A
Relay outputs
Switching capacity of contacts
вЂ” Thermal continuous current, max.			5 A
Cable length
в—Џ shielded, max.	1 000 m	1 000 m	1 000 m
в—Џ unshielded, max.	600 m	600 m	600 m
Isochronous mode
Isochronous operation (application synchronized up to terminal)	Yes; jitter incumbered < 100us	Yes	No
Interrupts/diagnostics/status information
Diagnostic functions	No	No	No
Substitute values connectable			Yes; 0/1
Diagnostics indication LED
в—Џ Status indicator digital output (green)	Yes	Yes	Yes
Parameter
Remark	3-byte parameter (not accessible for the user)	3 byte
Response to CPU/master STOP			Substitute a value/keep last value
Potential separation
Potential separation digital outputs
в—Џ between the channels	No	No	Yes
в—Џ between the channels and backplane bus	Yes	Yes	Yes
в—Џ Between the channels and load voltage L+			Yes
Isolation
Isolation tested with	500 V DC	500 V DC
tested with
в—Џ Channels against backplane bus and load voltage L+			1500 V AC
в—Џ Load voltage L+ against backplane bus			500 V DC
Ambient conditions
Ambient temperature during operation
в—Џ min.	-40 °C; = Tmin	-25 °C; = Tmin	-25 °C; = Tmin
в—Џ max.	70 °C; = Tmax	70 °C; = Tmax	60 °C; = Tmax
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width	15 mm	15 mm	15 mm
Height	81 mm	81 mm	81 mm
Depth	52 mm	52 mm	52 mm
Weights
Weight, approx.	40 g	40 g	50 g

skener.ru

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
Бесконтактные выключатели Конечные выключатели Оптические датчики Энкодеры

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FS - Установка умягчения

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FK - Установка обезжелезивания