Siemens
СРЕДСТВА ПРОМЫШЛЕННОЙ АВТОМАТИЗАЦИИ
официальный партнер Сименс
(4872) 700-366
skenergo@mail.ru
Accessories and spare parts
Slide rails with fixing bolts and tensioning screws to DIN 42923

Slide rails are used to tension the belt of a machine easily and conveniently when a belt tightener is not available. They are fixed to the base using stone bolts or foundation blocks.

The assignment of slide rails to motor size can be found in DIN 42923. For motors of frame sizes 355 to 450, there are no standardized slide rails (please inquire).

Available from:

Lutgert & Co. GmbH
Postfach 42 51
33276 Gutersloh, Germany
Tel. +49 (0)5241-74 07-0
Fax +49 (0)5241-74 07-90

http://www.luetgert-antriebe.de
e-mail:http://info@luetgert-antriebe.de

Foundation block acc. to DIN 799

The foundation blocks are inserted into the stone foundation and embedded in concrete. They are used for fixing machines of medium size, slide rails, pedestal bearings, baseframes, etc. After the fixing bolts have been unscrewed, the machine can be dragged without it having to be lifted.

When the machine is initially installed, the foundation block that is bolted to the machine (without washers) and fitted with taper pins is not embedded with concrete until the machine has been fully aligned. In this case, the machine is positioned 2 to 3 mm lower. The difference in shaft height is compensated by inserting shims on final installation. The taper pins safeguard the exact position of the machine when it is repeatedly removed and replaced without the need for realignment.

Available from:

Lutgert & Co. GmbH
Postfach 42 51
D-33276 Gutersloh, Germany
Tel. +49 (0)5241-74 07-0
Fax +49 (0)5241-74 07-90

http://www.luetgert-antriebe.de
e-mail:http://info@luetgert-antriebe.de

Taper pins to DIN 258 with threaded ends and constant taper lengths

Taper pins are used for components that are repeatedly removed. The drilled hole is ground conical using a conical reamer until the pin can be pushed in by hand until the cone shoulder lies 3 to 4 mm above the rim of the hole.

It can then be driven in using a hammer until it is correctly seated. The pin is removed from the drilled hole by screwing on the nut and tightening it.

Standardized taper pins are available from general engineering suppliers.

Available from:

Otto Roth GmbH & Co. KG
Rutesheimer Stra?e 22
70499 Stuttgart, Germany
Tel. +49 (0)711-1388-0
Fax. +49 (0)711-1388-233

http://www.ottoroth.de
e-mail:http://info@ottoroth.de

Couplings

The motor from Siemens is connected to the machine or gear unit through a coupling. Flender is an important coupling manufacturer with a wide range of products. For standard applications, Siemens recommends that elastic couplings of Flender types N-Eupex and Rupex or torsionally rigid couplings of types Arpex and Zapex are used. For special applications, Fludex and Elpex couplings are recommended.

Available from:

A. Friedr. Flender AG
Kupplungswerk Mussum
Industriepark Bocholt
Schlavenhorst 100
46395 Bocholt, Germany
Tel. +49 (0)2871-92 2185
Fax +49 (0)2871-92 2579

http://www.flender.com
e-mail:http://couplings@flender.com











Каталог оборудования

Приводная техника

Двигатели переменного тока

Низковольтные двигатели

Low-Voltage Motors - IEC Squirrel-Cage Motors

1LE1 motor generation

Standard motors up to frame size 315 L

Non-standard motors frame size 315 and above

Explosion-proof motors

Motors operating with frequency converters

Pump motors

Fan motors

Orientation

Self-ventilated in pole-changing version - Aluminium series 1LA7/5

Self-ventilated in pole-changing version - cast-iron series 1LG4

Forced-air cooled, w/o ext fan+cover - Alum. series 1PP7/5

Forced-air cooled, w/o ext fan+cover, high efficiency-cast-iron 1PP4

Forced-air cooled, w/o ext fan+cover, increased output-cast-iron 1PP4

Special versions

Accessories and spare parts

Dimensions

Compressor motors

Smoke-extraction motors

Marine motors

Синхронные двигатели с возбуждением от постояннымх магнитов

Асинхронные серводвигатели/двигатели главного движения

Синхронные двигатели

Моментные двигатели 1FW

Мотор-шпиндель 2SP1 ECS

Линейные двигатели

Линейные двигатели 1FN

Шаговые двигатели 1FL3 SIMOSTEP

Системы измерения

Стояночный тормоз

Асинхронные двигатели - стандартная линия

Двигатели постоянного тока

Децентрализованная приводная техника

Преобразователи

Преобразователи постоянного тока

Инструментальное программное обеспечение

Дополнительные компоненты

Техника автоматизации

Коммуникации и сети

Низковольтная коммутационная техника

Электроустановочная техника

Специализированные сенсоры

Блоки питания

Технология безопасности

Системные решения и продукты для отраслей

Сервис

Автоматизация процесса

... и все, что Вам еще необходимо


  © ООО "СК ЭНЕРГО" 2007-2022
  (4872) 700-366  skenergo@mail.ru
Яндекс.Метрика