SIPLUS TM Pulse 2x24V pulse output module . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS TM Pulse 2x24V pulse output module

| | | | | | |

Article number		6AG1138-6DB00-2BB1
		SIPLUS ET 200SP TM PULSE 2x24V
General information
Product type designation		TM Pulse 2x24 V
Firmware version		V1.0
в—Џ FW update possible		Yes
usable BaseUnits		BU type B1
Color code for module-specific color identification plate		CC40
Product function
в—Џ I&M data		Yes; I&M 0
в—Џ Isochronous mode		Yes
Engineering with
в—Џ PROFIBUS as of GSD version/GSD revision		GSD Revision 5
в—Џ PROFINET as of GSD version/GSD revision		GSDML V2.31
Supply voltage
Load voltage L+
в—Џ Rated value (DC)		24 V
в—Џ permissible range, lower limit (DC)		19.2 V
в—Џ permissible range, upper limit (DC)		28.8 V
в—Џ Short-circuit protection		Yes
в—Џ Reverse polarity protection		Yes; against destruction
Input current
Current consumption, max.		70 mA; without load
Encoder supply
Number of outputs		2; A common 24V encoder supply for both channels
24 V encoder supply
в—Џ 24 V		Yes; L+ (-0.8 V)
в—Џ Short-circuit protection		Yes; per module, electronic
в—Џ Output current, max.		300 mA
Power loss
Power loss, typ.		1.7 W
Address area
Occupied address area
в—Џ Inputs		16 byte; 8 per channel
в—Џ Outputs		24 byte; 12 per channel
Digital inputs
Number of digital inputs		2; 1 per channel
Digital inputs, parameterizable		Yes
Input characteristic curve in accordance with IEC 61131, type 3		Yes
Digital input functions, parameterizable
в—Џ Freely usable digital input		Yes
в—Џ HW enable for digital output		Yes
Input voltage
в—Џ Type of input voltage		DC
в—Џ Rated value (DC)		24 V
в—Џ for signal "0"		-30 to +5V
в—Џ for signal "1"		+11 to +30V
в—Џ permissible voltage at input, min.		-30 V
в—Џ permissible voltage at input, max.		30 V
Input current
в—Џ for signal "1", typ.		2.5 mA
Input delay (for rated value of input voltage)
for standard inputs
вЂ” parameterizable		Yes; none / 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms
вЂ” at "0" to "1", min.		4 µs; for parameterization "none"
вЂ” at "1" to "0", min.		4 µs; for parameterization "none"
Digital outputs
Type of digital output		P- and M-switching
Number of digital outputs		2; 1 per channel
Current-sinking		Yes
Current-sourcing		Yes
Digital outputs, parameterizable		Yes
Short-circuit protection		Yes; electronic/thermal
в—Џ Response threshold, typ.		6.8 A with Standard output, 2 A with High Speed output
Limitation of inductive shutdown voltage to		-0.8 V
Controlling a digital input		Yes
Accuracy of pulse duration		±100 ppm ±0.5 µs with High Speed output, ±100 ppm ±9 µs with Standard output
minimum pulse duration		1.5 µs; With High Speed output, 10 µs with Standard output
Digital output functions, parameterizable
в—Џ Freely usable digital output		Yes
в—Џ PWM output		Yes
вЂ” Number, max.		2; 1 per channel
вЂ” Cycle duration, parameterizable		Yes; Max. 85 s
вЂ” ON period, min.		0 %
вЂ” ON period, max.		100 %
вЂ” Resolution of the duty cycle		0.0036 %; For S7 analog format, min. 20 ns
в—Џ Connection of a proportional valve		Yes
в—Џ Dithering		Yes
вЂ” Frequency adjustable		Yes
вЂ” Amplitude adjustable		Yes
в—Џ Current measurement		Yes
в—Џ Current control		Yes
в—Џ Connection of a DC motor		Yes
в—Џ ON-delay		Yes
в—Џ OFF-delay		Yes
в—Џ Frequency output		Yes
в—Џ Pulse train		Yes
в—Џ Pulse output		Yes
Switching capacity of the outputs
в—Џ with resistive load, max.		2 A
в—Џ on lamp load, max.		10 W; 1 W with High Speed output
Load resistance range
в—Џ lower limit		12 в„¦; 240 ohm with High Speed output
в—Џ upper limit		12 kв„¦
Output voltage
в—Џ Type of output voltage		DC
в—Џ for signal "0", max.		1 V
в—Џ for signal "1", min.		23.2 V; L+ (-0.8 V)
Output current
в—Џ for signal "1" rated value		2 A; 0.1 A with High Speed output, observe derating
Output delay with resistive load
в—Џ "0" to "1", typ.		0 µs; With High Speed output, 4.5 µs with Standard output
в—Џ "0" to "1", max.		0.8 µs; With High Speed output, 9 µs with Standard output
в—Џ "1" to "0", typ.		0 µs; With High Speed output, 4.5 µs with Standard output
в—Џ "1" to "0", max.		0.8 µs; With High Speed output, 9 µs with Standard output
Parallel switching of two outputs
в—Џ for uprating		Yes
Switching frequency
в—Џ with resistive load, max.		100 kHz; With High Speed output, 10 kHz with standard output
в—Џ with inductive load, max.		100 kHz; With High Speed output, 10 kHz with standard output
в—Џ on lamp load, max.		10 Hz
Total current of the outputs
в—Џ Current per channel, max.		2 A
в—Џ Current per group, max.		4 A
в—Џ Current per module, max.		4 A
Isochronous mode
Isochronous operation (application synchronized up to terminal)		Yes
Bus cycle time (TDP), min.		250 µs; with 1 channel configuration, 375 µs with 2 channel configuration
Jitter, max.		1 µs; typically ±
Interrupts/diagnostics/status information
Diagnostics function		Yes
Substitute values connectable		Yes; Parameterizable
Alarms
в—Џ Diagnostic alarm		Yes
Diagnostic messages
в—Џ Monitoring the supply voltage		Yes
в—Џ Short-circuit		Yes
Diagnostics indication LED
в—Џ Monitoring of the supply voltage (PWR-LED)		Yes; green PWR LED
в—Џ Channel status display		Yes
в—Џ for module diagnostics		Yes; green/red DIAG LED
Potential separation
Potential separation channels
в—Џ between the channels		No
в—Џ between the channels and backplane bus		Yes
Permissible potential difference
between different circuits		75 V DC/60 V AC (base isolation)
Isolation
Isolation tested with		707 V DC (type test)
Ambient conditions
Ambient temperature during operation
в—Џ horizontal installation, min.		-40 °C; = Tmin; Startup @ -25 °C
в—Џ horizontal installation, max.		60 °C; Observe derating
в—Џ vertical installation, max.		50 °C; Observe derating
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Decentralized operation
to SIMATIC S7-300		Yes
to SIMATIC S7-400		Yes
to SIMATIC S7-1200		Yes
to SIMATIC S7-1500		Yes
to standard PROFIBUS master		Yes
to standard PROFINET controller		Yes
Dimensions
Width		20 mm
Weights
Weight, approx.		50 g

skener.ru

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
Бесконтактные выключатели Конечные выключатели Оптические датчики Энкодеры

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FS - Установка умягчения

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FK - Установка обезжелезивания