SIPLUS analog inputs . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS analog inputs

| | | | | |

Article number	6AG1134-6HD00-7BA1	6AG1134-6GD00-7BA1	6AG1134-6TD00-2CA1
	SIPLUS ET 200SP AI 4xU/I 2-wire ST	SIPLUS ET 200SP AI 4xI 2-/4-wire ST	SIPLUS ET 200SP AI 4XI 2-WIRE 4...20MA H
General information
Product type designation	AI 4xU/I 2-wire ST	AI 4xI 2-/4-wire ST	AI 4xI 2-wire HART
Firmware version
в—Џ FW update possible			Yes
usable BaseUnits			BU type A0, A1
Color code for module-specific color identification plate			CC03
Product function
в—Џ I&M data	Yes		Yes; I&M0 to I&M3
в—Џ Measuring range scalable			No
Engineering with
в—Џ STEP 7 TIA Portal configurable/integrated as of version	V11 SP2 with HSP 0024 / -
в—Џ STEP 7 configurable/integrated as of version	V5.5 SP2 with GSD file / -
в—Џ PROFIBUS as of GSD version/GSD revision			GSD Revision 5
в—Џ PROFINET as of GSD version/GSD revision			GSDML V2.3
Operating mode
в—Џ Oversampling			No
в—Џ MSI			No
CiR – Configuration in RUN
Reparameterization possible in RUN		Yes	Yes
Calibration possible in RUN			No
Supply voltage
Rated value (DC)	24 V	24 V	24 V
permissible range, lower limit (DC)	19.2 V	19.2 V	19.2 V
permissible range, upper limit (DC)	28.8 V	28.8 V	28.8 V
Reverse polarity protection	Yes		Yes
Input current
Current consumption, max.	37 mA; without sensor supply		25 mA; without sensor supply
24 V encoder supply
в—Џ 24 V	Yes		Yes
в—Џ Short-circuit protection	Yes		Yes
в—Џ Output current, max.	20 mA; max. 50 mA per channel for a duration < 10 s		20 mA; max. 50 mA per channel for a duration < 10 s
Power loss
Power loss, typ.	0.85 W; without sensor supply	0.85 W; Without encoder supply voltage	0.65 W; without sensor supply
Address area
Address space per module
в—Џ Address space per module, max.	8 byte	32 byte	8 byte; + 1 byte for QI information
в—Џ Address space per module with HART, max.			28 byte; + 1 byte for QI information
Analog inputs
Number of analog inputs	4; > 60 °C max. 1x ±20 mA or 4x ±10 V permissible	4; > 60 °C max. 1x ±20 mA permissible	4; Differential inputs
permissible input voltage for voltage input (destruction limit), max.	30 V
permissible input current for current input (destruction limit), max.	50 mA	50 mA	50 mA
Cycle time (all channels), min.	Sum of the basic conversion times and additional processing times (depending on the parameterization of the active channels)
Input ranges (rated values), voltages
в—Џ 0 to +10 V	Yes; 15 bit
в—Џ Input resistance (0 to 10 V)	120 kв„¦
в—Џ 1 V to 5 V	Yes; 15 bit
в—Џ Input resistance (1 V to 5 V)	120 kв„¦
в—Џ -10 V to +10 V	Yes; 16 bit incl. sign
в—Џ Input resistance (-10 V to +10 V)	120 kв„¦
в—Џ -5 V to +5 V	Yes; 16 bit incl. sign
в—Џ Input resistance (-5 V to +5 V)	120 kв„¦
Input ranges (rated values), currents
в—Џ 0 to 20 mA	Yes; 15 bit	Yes	No
в—Џ Input resistance (0 to 20 mA)	100 в„¦; + approx. 0.7 V diode forward voltage	100 в„¦; + approx. 0.7 V diode forward voltage in 2-wire operation
в—Џ -20 mA to +20 mA		Yes	No
в—Џ Input resistance (-20 mA to +20 mA)		100 в„¦
в—Џ 4 mA to 20 mA	Yes; 15 bit	Yes	Yes; 15 bit + sign
в—Џ Input resistance (4 mA to 20 mA)	100 в„¦; + approx. 0.7 V diode forward voltage	100 в„¦; + approx. 0.7 V diode forward voltage in 2-wire operation	280 в„¦; + approx. 0.35 V diode forward voltage
Cable length
в—Џ shielded, max.	200 m		800 m
Analog value generation for the inputs
Measurement principle	integrating (Sigma-Delta)		integrating (Sigma-Delta)
Integration and conversion time/resolution per channel
в—Џ Resolution with overrange (bit including sign), max.	16 bit		16 bit
в—Џ Integration time, parameterizable	Yes		Yes; channel by channel
в—Џ Interference voltage suppression for interference frequency f1 in Hz	16.6 / 50 / 60 Hz		10 / 50 / 60 Hz
в—Џ Conversion time (per channel)	180 / 60 / 50 ms
Smoothing of measured values
в—Џ Number of smoothing levels			4; None; 4/8/16 times
в—Џ parameterizable	Yes		Yes
в—Џ Step: None	Yes
в—Џ Step: low	Yes
в—Џ Step: Medium	Yes
в—Џ Step: High	Yes
Encoder
Connection of signal encoders
в—Џ for voltage measurement	Yes		No
в—Џ for current measurement as 2-wire transducer	Yes		Yes
вЂ” Burden of 2-wire transmitter, max.	650 в„¦
Errors/accuracies
Linearity error (relative to input range), (+/-)	0.01 %	0.01 %	0.01 %
Temperature error (relative to input range), (+/-)	0.005 %/K	0.005 %/K	0.005 %/K
Crosstalk between the inputs, min.	-50 dB	50 dB; Applies to up to ±5 V overvoltage in other channels	60 dB
Repeat accuracy in steady state at 25 °C (relative to input range), (+/-)	0.05 %	0.05 %	0.05 %
Operational error limit in overall temperature range
в—Џ Voltage, relative to input range, (+/-)	0.5 %
в—Џ Current, relative to input range, (+/-)	0.5 %	0.7 %	1 %
Basic error limit (operational limit at 25 °C)
в—Џ Voltage, relative to input range, (+/-)	0.3 %
в—Џ Current, relative to input range, (+/-)	0.3 %	0.3 %	0.3 %
Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency
в—Џ Series mode interference (peak value of interference < rated value of input range), min.	70 dB	70 dB	60 dB
в—Џ Common mode voltage, max.	10 V	10 V
в—Џ Common mode interference, min.	90 dB	90 dB
Isochronous mode
Isochronous operation (application synchronized up to terminal)			No
Interrupts/diagnostics/status information
Diagnostics function	Yes	Yes	Yes
Alarms
в—Џ Diagnostic alarm	Yes		Yes
в—Џ Limit value alarm			Yes
Diagnostic messages
в—Џ Monitoring the supply voltage	Yes	Yes	Yes
в—Џ Wire-break	Yes; at 4 to 20 mA	Yes; at 4 to 20 mA	Yes; channel by channel
в—Џ Short-circuit	Yes; with 1 to 5 V or 2-wire mode: Short-circuit of the encoder supply to ground or of an input to the encoder supply	Yes; 2-wire mode: Short-circuit of the encoder supply to ground or of an input to the encoder supply	Yes; Channel-by-channel, short-circuit of the encoder supply to ground or of an input to the encoder supply
в—Џ Group error		Yes	Yes
в—Џ Overflow/underflow	Yes		Yes; channel by channel
Diagnostics indication LED
в—Џ Monitoring of the supply voltage (PWR-LED)	Yes; Green LED		Yes; green PWR LED
в—Џ Channel status display	Yes; Green LED		Yes; Green LED
в—Џ for channel diagnostics			Yes; Red LED
в—Џ for module diagnostics	Yes; Green/red LED		Yes; green/red DIAG LED
Potential separation
Potential separation channels
в—Џ between the channels	Yes; channel group-specific between 2-wire current input group and voltage input group		No
в—Џ between the channels and backplane bus	Yes		Yes
в—Џ between the channels and the power supply of the electronics	Yes; only for voltage inputs		No
Permissible potential difference
between different circuits	75 V DC/60 V AC
between the inputs (UCM)	10 V DC	10 V DC
Isolation
Isolation tested with	707 V DC		707 V DC (type test)
Ambient conditions
Ambient temperature during operation
в—Џ horizontal installation, min.	-40 °C; = Tmin; Startup @ -25 °C	-40 °C; = Tmin	-40 °C; = Tmin; Startup @ -25 °C
в—Џ horizontal installation, max.	70 °C; = Tmax; > 60 °C max. 1x ±20 mA or 4x ±10 V permissible	70 °C; = Tmax; > 60 °C max. 1x ±20 mA permissible	60 °C
в—Џ vertical installation, min.	-40 °C; = Tmin; Startup @ -25 °C	-40 °C; = Tmin	-40 °C; = Tmin; Startup @ -25 °C
в—Џ vertical installation, max.	50 °C; = Tmax	50 °C; = Tmax	50 °C
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width	15 mm	15 mm	15 mm
Height	73 mm	73 mm	73 mm
Depth	58 mm	58 mm	58 mm
Weights
Weight, approx.		31 g	31 g

Article number	6AG1134-6HB00-2CA1	6AG1134-6HB00-2DA1	6AG1134-6JF00-2CA1	6AG1134-6JD00-2CA1
	SIPLUS ET 200SP AI 2 X U/I 2-, 4-WIRE HF	SIPLUS ET 200SP AI 2 X U/I 2-, 4-WIRE HS	SIPLUS ET 200SP AI 8XRTD/TC 2-WIRE HF	SIPLUS ET 200SP AI 4xRTD/TC HF
General information
Product type designation	AI 2xU/I 2-/4-wire HF	AI 2xU/I 2-/4-wire HS	AI 8xRTD/TC 2-wire HF	AI 4xRTD/TC 2-/3-/4-wire HF
Firmware version	V1.0	V2.0
в—Џ FW update possible	Yes	Yes	Yes
usable BaseUnits	BU type A0, A1	BU type A0, A1	BU type A0, A1
Color code for module-specific color identification plate	CC03	CC00	CC00
Product function
в—Џ I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes
в—Џ Measuring range scalable	No	No
Engineering with
в—Џ PROFIBUS as of GSD version/GSD revision	GSD Revision 5	GSD Revision 5	GSD Revision 5
в—Џ PROFINET as of GSD version/GSD revision	GSDML V2.3	GSDML V2.3	GSDML V2.3
Operating mode
в—Џ Oversampling	No	Yes; 2 channels per module	No
в—Џ MSI	No	No	No
CiR – Configuration in RUN
Reparameterization possible in RUN	Yes	Yes	Yes
Calibration possible in RUN	Yes	No	Yes
Supply voltage
Rated value (DC)	24 V	24 V	24 V	24 V
permissible range, lower limit (DC)	19.2 V	19.2 V	19.2 V	19.2 V
permissible range, upper limit (DC)	28.8 V	28.8 V	28.8 V	28.8 V
Reverse polarity protection	Yes	Yes	Yes	Yes
Input current
Current consumption (rated value)	39 mA; without sensor supply	39 mA; without sensor supply
Current consumption, max.			35 mA	35 mA
24 V encoder supply
в—Џ 24 V	Yes	Yes
в—Џ Short-circuit protection	Yes	Yes
в—Џ Output current, max.	20 mA; max. 50 mA per channel for a duration < 10 s (two-wire)	20 mA; max. 50 mA per channel for a duration < 10 s
Additional 24 V encoder supply
в—Џ Output current, max.	100 mA; max. 150 mA for a duration of < 10 s (four-wire)
Power loss
Power loss, typ.	0.95 W; without sensor supply	0.95 W; without sensor supply	0.75 W	0.75 W
Address area
Address space per module
в—Џ Address space per module, max.	4 byte; + 1 byte for QI information	4 byte; + 1 byte for QI information (32 bytes in the oversampling operating mode)	16 byte; + 1 byte for QI information	8 byte
Analog inputs
Number of analog inputs	2; Differential inputs	2; Differential inputs	8	4
permissible input voltage for voltage input (destruction limit), max.	30 V	30 V	30 V	30 V
permissible input current for current input (destruction limit), max.	50 mA	50 mA
Constant measurement current for resistance-type transmitter, typ.			2 mA	2 mA
Cycle time (all channels), min.		125 µs	Sum of the basic conversion times and additional processing times (depending on the parameterization of the active channels)	Sum of the basic conversion times and additional processing times (depending on the parameterization of the active channels); for line compensation in case of a three-wire connection, an additional cycle is necessary
Technical unit for temperature measurement adjustable			Yes; °C/°F/K	Yes; °C/°F/K
Analog input with oversampling		Yes
в—Џ Values per cycle, max.		16
в—Џ Resolution, min.		50 µs
Input ranges (rated values), voltages
в—Џ 0 to +10 V	Yes; 15 bit	Yes; 15 bit
в—Џ Input resistance (0 to 10 V)	75 kв„¦	75 kв„¦
в—Џ 1 V to 5 V	Yes; 15 bit	Yes; 13 bit
в—Џ Input resistance (1 V to 5 V)	75 kв„¦	75 kв„¦
в—Џ -1 V to +1 V			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (-1 V to +1 V)			1 Mв„¦	10 Mв„¦
в—Џ -10 V to +10 V	Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (-10 V to +10 V)	75 kв„¦	75 kв„¦
в—Џ -250 mV to +250 mV			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (-250 mV to +250 mV)			1 Mв„¦	10 Mв„¦
в—Џ -5 V to +5 V	Yes; 16 bit incl. sign	Yes; 15 bit incl. sign
в—Џ Input resistance (-5 V to +5 V)	75 kв„¦	75 kв„¦
в—Џ -50 mV to +50 mV			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (-50 mV to +50 mV)			1 Mв„¦	10 Mв„¦
в—Џ -80 mV to +80 mV			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (-80 mV to +80 mV)			1 Mв„¦	10 Mв„¦
Input ranges (rated values), currents
в—Џ 0 to 20 mA	Yes; 15 bit	Yes; 15 bit
в—Џ Input resistance (0 to 20 mA)	130 в„¦	130 в„¦
в—Џ -20 mA to +20 mA	Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (-20 mA to +20 mA)	130 в„¦	130 в„¦
в—Џ 4 mA to 20 mA	Yes; 15 bit	Yes; 14 bit
в—Џ Input resistance (4 mA to 20 mA)	130 в„¦	130 в„¦
Input ranges (rated values), thermocouples
в—Џ Type B			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Type B)			1 Mв„¦	1 Mв„¦
в—Џ Type C			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Type C)			1 Mв„¦	1 Mв„¦
в—Џ Type E			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Type E)			1 Mв„¦	1 Mв„¦
в—Џ Type J			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (type J)			1 Mв„¦	1 Mв„¦
в—Џ Type K			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Type K)			1 Mв„¦	1 Mв„¦
в—Џ Type L			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Type L)			1 Mв„¦	1 Mв„¦
в—Џ Type N			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Type N)			1 Mв„¦	1 Mв„¦
в—Џ Type R			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Type R)			1 Mв„¦	1 Mв„¦
в—Џ Type S			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Type S)			1 Mв„¦	1 Mв„¦
в—Џ Type T			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Type T)			1 Mв„¦	1 Mв„¦
в—Џ Type U			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Type U)			1 Mв„¦	1 Mв„¦
в—Џ Type TXK/TXK(L) to GOST			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Type TXK/TXK(L) to GOST)			1 Mв„¦	1 Mв„¦
Input ranges (rated values), resistance thermometer
в—Џ Cu 10				Yes; 16 bit incl. sign
в—Џ Input resistance (Cu 10)				1 Mв„¦
в—Џ Ni 100			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Ni 100)			1 Mв„¦	1 Mв„¦
в—Џ Ni 1000			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Ni 1000)			1 Mв„¦	1 Mв„¦
в—Џ LG-Ni 1000			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (LG-Ni 1000)			1 Mв„¦	1 Mв„¦
в—Џ Ni 120			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Ni 120)			1 Mв„¦	1 Mв„¦
в—Џ Ni 200			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Ni 200)			1 Mв„¦	1 Mв„¦
в—Џ Ni 500			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Ni 500)			1 Mв„¦	1 Mв„¦
в—Џ Pt 100			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Pt 100)			1 Mв„¦	1 Mв„¦
в—Џ Pt 1000			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Pt 1000)			1 Mв„¦	1 Mв„¦
в—Џ Pt 200			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Pt 200)			1 Mв„¦	1 Mв„¦
в—Џ Pt 500			Yes; 16 bit incl. sign	Yes; 16 bit incl. sign
в—Џ Input resistance (Pt 500)			1 Mв„¦	1 Mв„¦
Input ranges (rated values), resistors
в—Џ 0 to 150 ohms			Yes; 15 bit	Yes; 15 bit
в—Џ Input resistance (0 to 150 ohms)			1 Mв„¦	1 Mв„¦
в—Џ 0 to 300 ohms			Yes; 15 bit	Yes; 15 bit
в—Џ Input resistance (0 to 300 ohms)			1 Mв„¦	1 Mв„¦
в—Џ 0 to 600 ohms			Yes; 15 bit	Yes; 15 bit
в—Џ Input resistance (0 to 600 ohms)			1 Mв„¦	1 Mв„¦
в—Џ 0 to 3000 ohms			Yes; 15 bit	Yes; 15 bit
в—Џ Input resistance (0 to 3000 ohms)			1 Mв„¦	1 Mв„¦
в—Џ 0 to 6000 ohms			Yes; 15 bit	Yes; 15 bit
в—Џ Input resistance (0 to 6000 ohms)			1 Mв„¦	1 Mв„¦
в—Џ PTC			Yes; 15 bit	Yes; 15 bit
в—Џ Input resistance (PTC)			1 Mв„¦	1 Mв„¦
Thermocouple (TC)
Temperature compensation
вЂ” parameterizable			Yes	Yes
вЂ” Reference channel of the module			Yes	Yes
вЂ” internal comparison point			Yes; with BaseUnit type A1	Yes
вЂ” Reference channel of the group			Yes	Yes
вЂ” Number of reference channel groups			4; Group 0 to 3
вЂ” fixed reference temperature			Yes	Yes
Cable length
в—Џ shielded, max.	1 000 m; 200 m for voltage measurement	1 000 m; 200 m for voltage measurement	200 m; 50 m with thermocouples	200 m; 50 m with thermocouples
Analog value generation for the inputs
Measurement principle	Sigma Delta	Actual value encryption (successive approximation)	integrating (Sigma-Delta)	integrating (Sigma-Delta)
Integration and conversion time/resolution per channel
в—Џ Resolution with overrange (bit including sign), max.	16 bit	16 bit	16 bit	16 bit
в—Џ Integration time, parameterizable	Yes		Yes	Yes
в—Џ Basic conversion time, including integration time (ms)
вЂ” additional processing time for wire-break check			2 ms; In the ranges resistance thermometers, resistors and thermocouples	2 ms; In the ranges resistance thermometers, resistors and thermocouples
вЂ” additional power line wire-break check				2 ms; for 3/4 wire transducer (resistance thermometer and resistor)
в—Џ Interference voltage suppression for interference frequency f1 in Hz	16.6 / 50 / 60 / 300 / 600 / 1 200 / 2 400 / 4 800	No	16.6 / 50 / 60 Hz	16.6 / 50 / 60 Hz
в—Џ Conversion time (per channel)		10 µs	180 / 60 / 50 ms	180 / 60 / 50 ms
в—Џ Basic execution time of the module (all channels released)	1 ms
Smoothing of measured values
в—Џ Number of smoothing levels	6; none; 2-/4-/8-/16-/32-fold	7; none; 2-/4-/8-/16-/32-/64-fold	4; None; 4/8/16 times
в—Џ parameterizable	Yes	Yes	Yes	Yes
в—Џ Step: None				Yes
в—Џ Step: low				Yes
в—Џ Step: Medium				Yes
в—Џ Step: High				Yes
Encoder
Connection of signal encoders
в—Џ for voltage measurement	Yes	Yes	Yes	Yes
в—Џ for current measurement as 2-wire transducer	Yes	Yes
вЂ” Burden of 2-wire transmitter, max.	650 в„¦	650 в„¦
в—Џ for current measurement as 4-wire transducer	Yes	Yes
в—Џ for resistance measurement with two-wire connection			Yes	Yes
в—Џ for resistance measurement with three-wire connection			No	Yes
в—Џ for resistance measurement with four-wire connection			No	Yes
Errors/accuracies
Linearity error (relative to input range), (+/-)	0.02 %	0.03 %	0.01 %; ±0.1 % for resistance thermometers and resistance	0.01 %; ±0.1 % for resistance thermometers and resistance
Temperature error (relative to input range), (+/-)	0.005 %/K	0.01 %/K	0.0009 %/K; ±0.005 % / K at thermocouple	0.0009 %/K; ±0.005 % / K at thermocouple
Crosstalk between the inputs, min.	-50 dB	-50 dB	-50 dB	-50 dB
Repeat accuracy in steady state at 25 °C (relative to input range), (+/-)	0.01 %	0.1 %	0.05 %	0.05 %
Operational error limit in overall temperature range
в—Џ Voltage, relative to input range, (+/-)	0.2 %	0.5 %	0.2 %	0.1 %
в—Џ Current, relative to input range, (+/-)	0.2 %	0.5 %
в—Џ Resistance, relative to input range, (+/-)			0.2 %	0.1 %
Basic error limit (operational limit at 25 °C)
в—Џ Voltage, relative to input range, (+/-)	0.05 %; 0.1 % at SFU 4.8 kHz	0.2 %	0.05 %	0.05 %
в—Џ Current, relative to input range, (+/-)	0.05 %; 0.1 % at SFU 4.8 kHz	0.2 %
в—Џ Resistance, relative to input range, (+/-)			0.05 %	0.05 %
Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency
в—Џ Series mode interference (peak value of interference < rated value of input range), min.			70 dB	70 dB
в—Џ Common mode voltage, max.	35 V	35 V	10 V	10 V
в—Џ Common mode interference, min.	90 dB	90 dB	90 dB	90 dB
Isochronous mode
Isochronous operation (application synchronized up to terminal)	Yes	Yes	No
Filtering and processing time (TCI), min.	800 µs	80 µs
Bus cycle time (TDP), min.	1 ms	125 µs
Jitter, max.	5 µs
Interrupts/diagnostics/status information
Diagnostics function	Yes		Yes	Yes
Alarms
в—Џ Diagnostic alarm	Yes	Yes	Yes	Yes
в—Џ Limit value alarm	Yes; two upper and two lower limit values in each case	Yes; two upper and two lower limit values in each case	Yes; two upper and two lower limit values in each case	Yes; two upper and two lower limit values in each case
Diagnostic messages
в—Џ Monitoring the supply voltage	Yes		Yes	Yes
в—Џ Wire-break	Yes; Measuring range 4 to 20 mA only	Yes; channel-by-channel, at 4 to 20 mA only	Yes; channel by channel	Yes
в—Џ Short-circuit	Yes; For 1 to 5 V or for current measuring ranges short-circuit in encoder supply	Yes; channel-by-channel, at 1 to 5 V or for current measuring ranges short-circuit in encoder supply
в—Џ Group error	Yes	Yes	Yes
в—Џ Overflow/underflow	Yes	Yes	Yes; channel by channel	Yes
Diagnostics indication LED
в—Џ Monitoring of the supply voltage (PWR-LED)	Yes; green PWR LED	Yes; green PWR LED	Yes; green PWR LED	Yes; Green LED
в—Џ Channel status display	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED
в—Џ for channel diagnostics	Yes; Red LED	Yes; Red LED	Yes; Red LED	Yes; Red LED
в—Џ for module diagnostics	Yes; green/red DIAG LED	Yes; green/red DIAG LED	Yes; green/red DIAG LED	Yes; Green/red LED
Potential separation
Potential separation channels
в—Џ between the channels	Yes	Yes	No	No
в—Џ between the channels and backplane bus	Yes	Yes	Yes	Yes
в—Џ between the channels and the power supply of the electronics	Yes	Yes	Yes	Yes
Permissible potential difference
between different circuits	75 V DC/60 V AC (base isolation)	75 V DC/60 V AC (base isolation)	75 V DC/60 V AC (base isolation)	75 V DC/60 V AC
between the inputs (UCM)	75 V DC/60 V AC	75 V DC/60 V AC	10 V DC	10 V DC
Isolation
Isolation tested with	707 V DC (type test)	707 V DC (type test)	707 V DC (type test)	707 V DC
Ambient conditions
Ambient temperature during operation
в—Џ horizontal installation, min.	-40 °C; = Tmin; Startup @ -25 °C	-40 °C; = Tmin; Startup @ -25 °C	-40 °C; = Tmin; Startup @ -25 °C	-40 °C; = Tmin; Startup @ -25 °C
в—Џ horizontal installation, max.	60 °C; = Tmax	60 °C; = Tmax	60 °C	60 °C; = Tmax
в—Џ vertical installation, min.			-40 °C; = Tmin; Startup @ -25 °C	-40 °C; = Tmin; Startup @ -25 °C
в—Џ vertical installation, max.			50 °C	50 °C; = Tmax
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.	100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation	100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width	15 mm	15 mm	15 mm	15 mm
Height	73 mm	73 mm		73 mm
Depth	58 mm	58 mm		58 mm
Weights
Weight, approx.	32 g	32 g	32 g	30 g

Article number		6AG1134-6PA20-7BD0
		SIPLUS ET 200SP AI EMETER 480VAC ST
General information
Product type designation		ET 200SP, AI Energy Meter 480 V AC ST, PU 1
usable BaseUnits		BU type D0, BU20-P12+A0+0B
Product function
в—Џ Voltage measurement		Yes
в—Џ Voltage measurement with voltage transformers		Yes
в—Џ Current measurement		Yes
в—Џ Phase current measurement without current transformers		No
в—Џ Phase current measurement with current transformers		Yes
в—Џ Energy measurement		Yes
в—Џ Frequency measurement		Yes
в—Џ Power measurement		Yes
в—Џ Active power measurement		Yes
в—Џ Reactive power measurement		Yes
в—Џ I&M data		Yes; I&M0 to I&M3
в—Џ Isochronous mode		No
Operating mode
в—Џ cyclic measurement		Yes
в—Џ acyclic measurement		Yes
в—Џ Acyclic measured value access		Yes
в—Џ Fixed measured value sets		Yes
в—Џ Freely definable measured value sets		Yes
Configuration control
via dataset		Yes
CiR – Configuration in RUN
Reparameterization possible in RUN		Yes
Calibration possible in RUN		Yes
Installation type/mounting
Mounting position		Any
Supply voltage
Design of the power supply		Supply via voltage measurement channel L1
Type of supply voltage		AC 100 - 277 V
permissible range, lower limit (AC)		90 V
permissible range, upper limit (AC)		293 V
Line frequency
в—Џ permissible range, lower limit		47 Hz
в—Џ permissible range, upper limit		63 Hz
Power loss
Power loss, typ.		0.6 W
Address area
Address space per module
в—Џ Address space per module, max.		268 byte; 256 byte input / 12 byte output
Hardware configuration
Automatic encoding
в—Џ Mechanical coding element		Yes
Time of day
Operating hours counter
в—Џ present		Yes
Analog inputs
Cycle time (all channels), typ.		50 ms; Time for consistent update of all measured and calculated values (cyclic und acyclic data)
Interrupts/diagnostics/status information
Alarms
в—Џ Diagnostic alarm		Yes
в—Џ Limit value alarm		Yes
в—Џ Hardware interrupt		Yes; Monitoring of up to 16 freely selectable process values (exceeding or undershooting of value)
Diagnostics indication LED
в—Џ Monitoring of the supply voltage (PWR-LED)		Yes
в—Џ Channel status display		Yes; Green LED
в—Џ for channel diagnostics		Yes; red Fn LED
в—Џ for module diagnostics		Yes; green/red DIAG LED
Integrated Functions
Measuring functions
в—Џ Measuring procedure for voltage measurement		TRMS
в—Џ Measuring procedure for current measurement		TRMS
в—Џ Type of measured value acquisition		seamless
в—Џ Curve shape of voltage		Sinusoidal or distorted
в—Џ Buffering of measured variables		Yes
в—Џ Parameter length		74 byte
в—Џ Bandwidth of measured value acquisition		2 kHz; Harmonics: 39 / 50 Hz, 32 / 60 Hz
Operating mode for measured value acquisition
вЂ” automatic detection of line frequency		No; Parameterizable
Measuring range
вЂ” Frequency measurement, min.		45 Hz
вЂ” Frequency measurement, max.		65 Hz
Measuring inputs for voltage
вЂ” Measurable line voltage between phase and neutral conductor		277 V
вЂ” Measurable line voltage between the line conductors		480 V
вЂ” Measurable line voltage between phase and neutral conductor, min.		90 V
вЂ” Measurable line voltage between phase and neutral conductor, max.		293 V
вЂ” Measurable line voltage between the line conductors, min.		155 V
вЂ” Measurable line voltage between the line conductors, max.		508 V
вЂ” Measurement category for voltage measurement in accordance with IEC 61010-2-030		CAT II; CAT III in case of guaranteed protection level of 1.5 kV
вЂ” Internal resistance line conductor and neutral conductor		3.4 Mв„¦
вЂ” Power consumption per phase		20 mW
вЂ” Impulse voltage resistance 1,2/50µs		1 kV
Measuring inputs for current
вЂ” measurable relative current (AC), min.		1 %; Relative to the secondary rated current 5 A
вЂ” measurable relative current (AC), max.		100 %; Relative to the secondary rated current 5 A
вЂ” Continuous current with AC, maximum permissible		5 A; at > +60 °C max. permissible current 1 A per phase
вЂ” Apparent power consumption per phase for measuring range 5 A		0.6 V·A
вЂ” Rated value short-time withstand current restricted to 1 s		100 A
вЂ” Input resistance measuring range 0 to 5 A		25 mв„¦; At the terminal
вЂ” Zero point suppression		Parameterizable: 2 ... 250 mA, default 50 mA
вЂ” Surge strength		10 A; for 1 minute
Accuracy class according to IEC 61557-12
вЂ” Measured variable voltage		0,2
вЂ” Measured variable current		0,2
вЂ” Measured variable apparent power		0.5
вЂ” Measured variable active power		0.5
вЂ” Measured variable reactive power		1
вЂ” Measured variable power factor		0.5
вЂ” Measured variable active energy		0.5
вЂ” Measured variable reactive energy		1
вЂ” Measured variable neutral current		0.5; calculated
вЂ” Measured variable phase angle		±1 °; not covered by IEC 61557-12
вЂ” Measured variable frequency		0.05
Potential separation
Potential separation channels
в—Џ between the channels and backplane bus		Yes; 3 700V AC (type test) CAT III
Isolation
Isolation tested with		2 300V AC for 1 min. (type test)
Ambient conditions
Ambient temperature during operation
в—Џ horizontal installation, min.		-40 °C; = Tmin; < -25 °C min. permissible supply voltage 110 V AC
в—Џ horizontal installation, max.		70 °C; = Tmax; > +60 °C max. permissible current 1 A per phase
в—Џ vertical installation, min.		-40 °C; = Tmin
в—Џ vertical installation, max.		50 °C; = Tmax
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width		20 mm
Height		73 mm
Depth		58 mm
Weights
Weight (without packaging)		45 g
Data for selecting a current transformer
в—Џ Burden power current transformer x/1A, min.		As a function of cable length and cross section, see device manual
в—Џ Burden power current transformer x/5A, min.		As a function of cable length and cross section, see device manual

skener.ru

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
Бесконтактные выключатели Конечные выключатели Оптические датчики Энкодеры

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FS - Установка умягчения

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FK - Установка обезжелезивания