SIPLUS digital outputs . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS digital outputs

| | | | | |

Article number	6AG1132-6BD20-7BA0	6AG1132-6BF00-7BA0	6AG1132-6BH00-7BA0
	SIPLUS ET200SP DQ 4x24VDC/2A ST	SIPLUS ET 200SP DQ 8x24VDC/0,5A ST	SIPLUS ET 200SP DQ 16x24VDC/0,5A ST
General information
Product type designation	DQ 4x24VDC/2A ST	DQ 8x24VDC/0.5A ST	DQ 16x24VDC/0.5A ST
Redundancy
в—Џ Redundancy capability		Yes
Supply voltage
Rated value (DC)	24 V	24 V	24 V
permissible range, lower limit (DC)	19.2 V	19.2 V	19.2 V
permissible range, upper limit (DC)	28.8 V	28.8 V	28.8 V
Power loss
Power loss, typ.	1 W	1 W	1 W
Address area
Address space per module
в—Џ Address space per module, max.	32 byte	32 byte	32 byte
Digital outputs
Number of digital outputs	4; > +60 °C number of simultaneously controllable outputs max. 2 x 0.25 A or max. 4 x 0.125 A, max. total current 0.5 A	8; > +60 °C max. total current 1.0 A	16; > +60 °C max. total current 1.0 A
Current-sourcing			Yes
Short-circuit protection		Yes
в—Џ Response threshold, typ.	2.8 to 5.2 A	0.7 to 1.3 A	0.7 to 1.3 A
Limitation of inductive shutdown voltage to	Typ. L+ (-50 V)	Typ. L+ (-50 V)	Typ. L+ (-50 V)
Controlling a digital input	Yes	Yes	Yes
Switching capacity of the outputs
в—Џ with resistive load, max.	2 A	0.5 A	0.5 A
в—Џ on lamp load, max.	10 W	5 W	5 W
Load resistance range
в—Џ lower limit	12 в„¦	48 в„¦	48 в„¦
в—Џ upper limit	3 400 в„¦	12 kв„¦	12 kв„¦
Output current
в—Џ for signal "1" rated value	2 A	0.5 A	0.5 A
Output delay with resistive load
в—Џ "0" to "1", max.	50 µs	50 µs	50 µs
в—Џ "1" to "0", max.	100 µs	100 µs	100 µs
Parallel switching of two outputs
в—Џ for uprating	No	No	No
в—Џ for redundant control of a load	Yes	Yes	Yes
Switching frequency
в—Џ with resistive load, max.	100 Hz	100 Hz	100 Hz
в—Џ with inductive load, max.	2 Hz	2 Hz	2 Hz
в—Џ on lamp load, max.	10 Hz	10 Hz	10 Hz
Cable length
в—Џ shielded, max.	1 000 m	1 000 m	1 000 m
в—Џ unshielded, max.	200 m	200 m	200 m
Diagnostic messages
в—Џ Monitoring the supply voltage	Yes	Yes	Yes
в—Џ Wire-break	Yes	Yes	Yes
в—Џ Short-circuit	Yes	Yes	Yes
в—Џ Group error	Yes	Yes	Yes
Permissible potential difference
between different circuits	75 V DC/60 V AC	75 V DC/60 V AC	75 V DC/60 V AC
Isolation
Isolation tested with	707 V DC	707 V DC	707 V DC
Ambient conditions
Ambient temperature during operation
в—Џ horizontal installation, min.	-40 °C; = Tmin	-40 °C; = Tmin; Startup @ -25 °C	-40 °C; = Tmin
в—Џ horizontal installation, max.	70 °C; = Tmax; > +60 °C number of simultaneously controllable outputs max. 2 x 0.25 A or max. 4 x 0.125 A, max. total current 0.5 A	70 °C; = Tmax; > +60 °C max. total current 1.0 A	70 °C; = Tmax; > +60 °C max. total current 1.0 A
в—Џ vertical installation, min.	-40 °C; = Tmin	-40 °C; = Tmin; Startup @ -25 °C	-40 °C; = Tmin
в—Џ vertical installation, max.	50 °C; = Tmax	50 °C; = Tmax	50 °C; = Tmax
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.	100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width	15 mm	15 mm	15 mm
Height	73 mm	73 mm	73 mm
Depth	58 mm	58 mm	58 mm
Weights
Weight, approx.	30 g	28 g	28 g

Article number	6AG1132-6BF00-7CA0	6AG1132-6GD50-2BA0	6AG1132-6HD00-7BB1
	SIPLUS ET 200SP DQ 8X24VDC/0,5A HF	SIPLUS ET 200SP RQ 4X24VDC/2A CO ST	SIPLUS ET 200SP RQ 4x120VDC/230VAC/5A
General information
Product type designation	DQ 8x24VDC/0.5A HF	RQ 4x24VUC/2A CO ST	RQ 4x120 VDC вЂ¦ 230 VAC/5 A NO ST
Firmware version	V1.2	V1.0
в—Џ FW update possible	Yes	Yes	Yes
usable BaseUnits	BU type A0	BU type A0	BU type B0, B1
Color code for module-specific color identification plate	CC02	CC00	CC00
Product function
в—Џ I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
Engineering with
в—Џ PROFIBUS as of GSD version/GSD revision	GSD Revision 5	GSD Revision 5	GSD Revision 5
в—Џ PROFINET as of GSD version/GSD revision	GSDML V2.3	GSDML V2.3	GSDML V2.3
Operating mode
в—Џ DQ	Yes	Yes	Yes
в—Џ DQ with energy-saving function	No	No	No
в—Џ PWM	No	No	No
в—Џ Oversampling	No	No	No
в—Џ MSO	Yes	No	No
Supply voltage
Rated value (DC)	24 V	24 V	24 V
permissible range, lower limit (DC)	19.2 V	19.2 V	19.2 V
permissible range, upper limit (DC)	28.8 V	28.8 V	28.8 V
Reverse polarity protection	Yes		Yes
Input current
Current consumption (rated value)		50 mA
Current consumption, max.	45 mA; without load		100 mA; without load
Output voltage
Rated value (DC)	24 V
Power loss
Power loss, typ.	1 W	1.2 W	1.5 W
Address area
Address space per module
в—Џ Address space per module, max.	1 byte; + 1 byte for QI information	1 byte; + 1 byte for QI information	1 byte; + 1 byte for QI information
в—Џ Inputs		1 byte; With QI	1 byte; With QI
в—Џ Outputs		1 byte	1 byte
Digital outputs
Type of digital output		Relays	Relays
Number of digital outputs	8	4	4
Current-sinking	No
Current-sourcing	Yes
Short-circuit protection		No	No
в—Џ Response threshold, typ.	0.7 to 1.3 A
Limitation of inductive shutdown voltage to	Typ. L+ (-50 V)
Controlling a digital input	Yes
Switching capacity of the outputs
в—Џ with resistive load, max.	0.5 A
в—Џ on lamp load, max.	5 W
Load resistance range
в—Џ lower limit	48 в„¦
в—Џ upper limit	12 kв„¦
Output current
в—Џ for signal "1" rated value	0.5 A
в—Џ for signal "0" residual current, max.	0.1 mA
Output delay with resistive load
в—Џ "0" to "1", typ.	50 µs
в—Џ "1" to "0", typ.	100 µs
Parallel switching of two outputs
в—Џ for uprating	No
в—Џ for redundant control of a load	Yes
Switching frequency
в—Џ with resistive load, max.	100 Hz	2 Hz	2 Hz
в—Џ with inductive load, max.	2 Hz		0.5 Hz
в—Џ on lamp load, max.	10 Hz		2 Hz
Total current of the outputs
в—Џ Current per channel, max.	0.5 A	2 A	5 A
в—Џ Current per module, max.	4 A	8 A	20 A
Total current of the outputs (per module)
horizontal installation
вЂ” up to 60 °C, max.	4 A	8 A	20 A
vertical installation
вЂ” up to 60 °C, max.	4 A	8 A	20 A
Relay outputs
в—Џ Number of relay outputs		4	4
в—Џ Rated supply voltage of relay coil L+ (DC)		24 V	24 V
в—Џ Current consumption of relays (coil current of all relays), max.		40 mA	40 mA
в—Џ external protection for relay outputs			Yes, with 6A
в—Џ Number of operating cycles, max.			7 000 000; see additional description in the manual
Switching capacity of contacts
вЂ” with inductive load, max.			2 A; see additional description in the manual
вЂ” with resistive load, max.		2 A	5 A; see additional description in the manual
вЂ” Thermal continuous current, max.		2 A	5 A; Max. 1 385 VA, 150 W
вЂ” Switching current, min.		1 mA; 5 V DC	100 mA; 5 V DC
вЂ” Rated switching voltage (DC)		24 V	24 V DC to 120 V DC
вЂ” Rated switching voltage (AC)		24 V	24V AC to 230V AC
Cable length
в—Џ shielded, max.	1 000 m	1 000 m	1 000 m
в—Џ unshielded, max.	600 m	200 m	200 m
Isochronous mode
Isochronous operation (application synchronized up to terminal)	Yes	No	No
Execution and activation time (TCO), min.	48 µs
Bus cycle time (TDP), min.	500 µs
Interrupts/diagnostics/status information
Diagnostics function	Yes	Yes	Yes
Substitute values connectable	Yes	Yes	Yes
Alarms
в—Џ Diagnostic alarm	Yes	Yes	Yes
Diagnostic messages
в—Џ Monitoring the supply voltage	Yes	Yes	Yes
в—Џ Wire-break	Yes; channel by channel	No	No
в—Џ Short-circuit	Yes; channel by channel	No	No
в—Џ Group error	Yes	Yes	Yes
Diagnostics indication LED
в—Џ Monitoring of the supply voltage (PWR-LED)	Yes; green PWR LED	Yes; green PWR LED	Yes; green PWR LED
в—Џ Channel status display	Yes; Green LED	Yes; Green LED	Yes; Green LED
в—Џ for channel diagnostics	Yes; Red LED	No	No
в—Џ for module diagnostics	Yes; green/red DIAG LED	Yes; green/red DIAG LED	Yes; green/red DIAG LED
Potential separation
Potential separation channels
в—Џ between the channels	No	Yes	Yes
в—Џ between the channels and backplane bus	Yes	Yes	Yes
в—Џ between the channels and the power supply of the electronics		Yes	Yes
Permissible potential difference
between different circuits	75 V DC/60 V AC (base isolation)	75 V DC/60 V AC (base isolation)
between channels and backplane bus/supply voltage			240 V AC
Isolation
Isolation tested with	707 V DC (type test)	707 V DC (type test)	2 500 V DC (type test)
tested with
в—Џ between channels and backplane bus/supply voltage			2500 V DC
в—Џ between backplane bus and supply voltage			707 V DC (type test)
Ambient conditions
Ambient temperature during operation
в—Џ horizontal installation, min.	-40 °C; = Tmin	-40 °C; = Tmin; Startup @ -25 °C	-40 °C; = Tmin
в—Џ horizontal installation, max.	70 °C; = Tmax; > +60 °C max. total current 1.0 A	60 °C; = Tmax	70 °C; = Tmax; see Derating BasedOn (e.g. manual), additionally Tmax > 60 °C max. continuous current of 3 A per relay
в—Џ vertical installation, min.	-40 °C; = Tmin
в—Џ vertical installation, max.	50 °C; = Tmax
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)	Tmin ... Tmax at 1 140 hPa ... 795 hPa (-1 000 m ... +2 000 m) // Tmin ... Tmax -5K) at 795 hPa ... 701 hPa (+2 000 m ... +3 000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.	100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation	100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation	100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width	15 mm	15 mm	20 mm
Height		73 mm	73 mm
Depth		58 mm	58 mm
Weights
Weight, approx.	30 g	30 g	40 g

Article number		6AG1132-6BD20-7CA0
		SIPLUS ET 200SP DQ 4X24VDC/2A HF
General information
Product type designation		DQ 4x24 V DC/2 A HF
Firmware version		V1.0
в—Џ FW update possible		Yes
usable BaseUnits		BU type A0
Color code for module-specific color identification plate		CC02
Product function
в—Џ I&M data		Yes; I&M0 to I&M3
Engineering with
в—Џ PROFIBUS as of GSD version/GSD revision		GSD Revision 5
в—Џ PROFINET as of GSD version/GSD revision		GSDML V2.3
Operating mode
в—Џ Oversampling		No
Supply voltage
Rated value (DC)		24 V
permissible range, lower limit (DC)		19.2 V
permissible range, upper limit (DC)		28.8 V
Reverse polarity protection		Yes
Input current
Current consumption, max.		60 mA; without load
Power loss
Power loss, typ.		1 W
Address area
Address space per module
в—Џ Address space per module, max.		1 byte; + 1 byte for QI information
Isochronous mode
Isochronous operation (application synchronized up to terminal)		Yes
Bus cycle time (TDP), min.		500 µs
Jitter, max.		8 µs
Interrupts/diagnostics/status information
Diagnostics function		Yes
Substitute values connectable		Yes
Alarms
в—Џ Diagnostic alarm		Yes
Diagnostic messages
в—Џ Monitoring the supply voltage		Yes
в—Џ Wire-break		Yes; channel by channel
в—Џ Short-circuit		Yes; channel by channel
в—Џ Group error		Yes
Diagnostics indication LED
в—Џ Monitoring of the supply voltage (PWR-LED)		Yes; green PWR LED
в—Џ Channel status display		Yes; Green LED
в—Џ for channel diagnostics		Yes; Red LED
в—Џ for module diagnostics		Yes; green/red DIAG LED
Potential separation
Potential separation channels
в—Џ between the channels		No
в—Џ between the channels and backplane bus		Yes
Isolation
Isolation tested with		707 V DC (type test)
Ambient conditions
Ambient temperature during operation
в—Џ horizontal installation, min.		-40 °C; = Tmin
в—Џ horizontal installation, max.		70 °C; = Tmax; see Derating BasedOn (e.g. manual), additionally Tmax > 60 °C max. total current 1 A
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width		15 mm
Height		73 mm
Depth		58 mm
Weights
Weight, approx.		30 g