Input

Measured variable

Level

Span (infinitely adjustable)

Span (min. ... max.)

Max. permissible operating pressure

1.25 ... 250 mbar 
(0.5 вЂ¦ 100 inH₂O)

See "Mounting flange"

6.25 ... 1250 mbar
(2.5 вЂ¦ 500 inH₂O)

31.25 ... 6250 mbar
(12.54 вЂ¦ 2509 inH₂O)

Low measuring limit

• Measuring cell with silicone oil filling

-100% of max. span or 500 mbar a (7.25 psia) vacuum resistance

Also available as vacuum-resistant remote seal: 30 mbar a (0.44 psia)

Upper measuring limit

100 % of max. span

Start of scale

Between measuring limits (infinitely adjustable)

Output

Output signal

4 ... 20 mA

• Lower limit (infinitely adjustable)

3.55 mA, factory preset to 3.8 mA

• Upper limit (infinitely adjustable)

23 mA, factory preset to 20.5 mA

• Ripple (without HART communication)

I_pp ≤ 0.4% of max. output current

• adjustable damping

0... 100 s in steps of 0.1 s, factory-set to 2 s

• current transmitter

3.55 ... 23 mA

• Failure signal

Adjustable within limits:

• Bottom: 3.55 вЂ¦ 3.7 mA (factory preset to 3.6 mA)
• Top: 21.0 вЂ¦ 23 mA (factory preset to 22.8 mA)

Load

• Without HART communication

R_B ≤ (U_H - 10.5 V)/0.023 A in О©,
U_H : Power supply in V

• With HART communication

• HART communicator

R_B = 230 ... 1100 О©

• HART modem

R_B = 230 ... 500 О©

Characteristic curve

Linearly rising or linearly falling and user-specific

Measuring accuracy

Reference conditions (in accordance with IEC-60770-1)

All error information always refers to the set span.

• Rising characteristic curve
• Start of scale 0 bar
• Seal diaphragm stainless steel
• Measuring cell with silicone oil filling
• Room temperature (25 °C (77 °F))

Error in measurement at limit setting including hysteresis and reproducibility

r: Span ratio
(r = max. span / set span)

Linear characteristic

r ≤ 10

r > 10

• 250 mbar (100 inH₂O)
  1250 mbar (502 inH₂O)
  6250 mbar (2509 inH₂O)

≤ 0.03 %

≤ (0.003 ^. r) %

Long-term stability

≤ (0.05 ^. r) % every 5 years

≤ (0.08 ^. r) % every 10 years

Influence of ambient temperature per 28 °C (50 °F)¹⁾

• 250 mbar (100 inH₂O)

≤ (0.025 · r + 0.014) %

• 250 mbar (502 inH₂O)
  6250 mbar (2509 inH₂O)

≤ (0.006 · r + 0.03) %

Effect of static pressure

• At the start of scale value (PKN)

• 250 mbar (100 inH₂O)

≤ (0.035 · r) % per 70 bar (1015 psi) correction via zero point correction

• 250 mbar (502 inH₂O)
  6250 mbar (2509 inH₂O)

≤ (0.007 · r) % per 70 bar (1015 psi) correction via zero point correction

• On the span (PKS)

• 250 mbar (100 inH₂O)
  1250 mbar (502 inH₂O)

≤ 0.03% per 70 bar (1015 psi)

• 6250 mbar (2509 inH₂O)

≤ 0.09% per 70 bar (1015 psi)

Influence of power supply

≤ 0.005%/1 V

Rated conditions

Mounting position

Defined by flange

Ambient conditions

• Ambient temperature
  (Note: Observe the temperature class in areas subject to explosion hazard.)

• total device

-40 ... +85 °C (-40 ... +185 °F)

• Display readable

-20 ... +85 °C (-4 ... +185 °F)

• Storage temperature

-50 ... +90 °C (-58 ... +194 °F)

Climatic class

• Condensation

Relative humidity 0 вЂ¦ 100 % (condensation permissible)

Degree of protection according to IEC 60529

IP66/IP68 and NEMA 4X (with corresponding cable gland)

Electromagnetic compatibility

• Emitted interference and interference immunity

According to IEC 61326 and NAMUR NE 21

Permissible pressures

According to 2014/68/EU pressure equipment directive

Measuring temperature (for low-pressure side)

• Measuring cell with silicone oil filling

• p_abs ≥ 1 bar

-40 ... +175²⁾ °C (-40 ... +257²⁾ °F)

• p_abs < 1 bar

-40 ... +80 °C (-40 ... +176 °F)

Design

Weight

• To EN (pressure transmitter with mounting flange, without tube)

approx. 9.8 … 11.8 kg (21.6 … 26.0 lb)

• To ASME (pressure transmitter with mounting flange, without tube)

approx. 9.8 … 16.8 kg (21.6 … 37.0 lb)

Material of wetted parts at the high-pressure side

• Seal diaphragm of mounting flange

Stainless steel 1.4404 /316L, Hastelloy C276 mat. no. 2.4819, Monel 400 mat. no. 2.4360, tantalum, PFA on stainless steel 1.4404/316L, PTFE on stainless steel 1.4404 / 316L

• Sealing face

Smooth to EN 1092‑-1, form B1 or ASME B16.5 RF 125 … 250 AA for stainless steel 316L, EN 1092-1 form B2 or ASME B16.5 RFSF for the remaining materials

• Sealing material in the process connection

• O-ring

Standard

• PTFE

Optional

• NBR
• PTFE (virginal)
• PTFE (glass-fiber reinforced)
• FFPM (Kalrez)
• Graphite

• For vacuum application of mounting flange

Copper

Material of wetted parts at the low-pressure side

• Seal diaphragm

Stainless steel, mat. no. 1.4404/316L, Hastelloy C276, Monel 400

• Process connection and sealing screw

Stainless steel, mat. no. 1.4404/316L

• Sealing material in the process connection

• O-ring

Standard

• Viton (FKM (FPM))

Optional

• NBR
• PTFE (virginal)
• PTFE (glass-fiber reinforced)
• FFPM (Kalrez)
• Graphite

Material of parts not in contact with media

• Die-cast aluminum housing

• Low copper die-cast aluminum AC-AlSi12 (Fe) or AC-AlSi 10 Mg (Fe) to EN 1706
• Lacquer on polyurethane base, optional epoxy-based primer
• Stainless steel type plate, mat. no. 1.4404/316L

• Stainless steel precision cast housing

Stainless steel, mat. no. 1.4404/316L

• Process connection screws

Stainless steel, mat. no. 1.4404/316L

Measuring cell filling

Silicone oil

• Liquid mounting flange

Silicone oil or other material

Process connection

• High-pressure side

Flange to EN and ASME

• Low-pressure side

ј-18 NPT female thread and flange connection with M10 to DIN 19213 or 7/16-20 UNF fastening thread to IEC 61518/DIN EN 61518

Electrical connection

• Screw terminals
• Cable entry via the following screwed glands:
  • M20 x 1.5
  • Ѕ-14 NPT
  • Han 7D/Han 8D connector
  • M12 connector

Displays and controls

Keys

3; for operation directly on the device

Display

• With or without integrated display
• Cover with or without window

Auxiliary power

Terminal voltage on transmitter

• 10.6 ... 44 V DC
• With intrinsically safe operation 10.6 ... 30 V DC

Certificates and approvals

Classification according to pressure equipment directive (PED 2014/68/EU)

• PN 160 (MAWP 2320 psi)

For gases of fluid group 1 and liquids of fluid group 1; complies with requirements of article 4, paragraph 3 (sound engineering practice)

Explosion protection

Explosion protection for Europe (according to ATEX)

• Intrinsic safety "i"

PTB 09 ATEX 2004 X

• Marking

Ex II 1/2 G Ex ia/ib IIC T4

• Permissible ambient temperature

-40 ... +85 °C (-40 ... +185 °F)

• Wiring

To certified intrinsically-safe circuits with peak values:
U_i = 30 V, I_i = 100 mA, P_i = 750 mW; R_i = 300 О©

• Effective internal inductance

L_i = 400 µH

• Effective internal capacitance

C_i = 6 nF

• Flameproof enclosure "d"

BVS 09 ATEX E 027

• Marking

Ex II 1/2 G Ex db ia IIC T4/T6 Ga/Gb

• Permissible ambient temperature

-40 ... +85 °C (-40 ... +185 °F) temperature class T4;
-40 ... +60 °C (-40 ... +140 °F) temperature class T6

• Wiring

To circuits with operating values: U_m = 10.5 ... 45 V DC

• Dust explosion protection for zone 20

BVS 09 ATEX E 027

• Marking

Ex II 1 D Ex ta ia IIIC T120 °C Da

• Permissible ambient temperature

-40 ... +85 °C (-40 ... +185 °F)

• Max. surface temperature

120 °C (248 °F)

• Wiring

To certified intrinsically-safe circuits with peak values:
U_i = 30 V, I_i = 100 mA, P_i = 750 mW, R_i = 300 О©

• Effective internal inductance

L_i = 400 µH

• Effective internal capacitance

C_i = 6 nF

• Dust explosion protection for zone 21/22

BVS 09 ATEX E 027

• Marking

Ex II 2 D Ex tb ia IIIC T120 °C Db

• Wiring

To circuits with operating values: U_H = 10.5 ... 45 V DC; P_max = 1.2 W

• Type of protection "n" (zone 2)

PTB 09 ATEX 2004 X

• Marking

Ex II 3 G Ex nA II T4/T6
Ex II 2/3 G Ex ib/nL IIC T4/T6
Ex II 2/3 G Ex ib/ic IIC T4/T6

• "nA, ic" connection

U_m = 45 V DC

• "nL" connection

U_i = 45 V

• Effective internal inductance

L_i = 400 µH

• Effective internal capacitance

C_i = 6 nF

Explosion protection for USA

(acc. to FM)

Certificate of Compliance

No. 3033013

• Marking (XP/DIP) or (IS)

XP CL I, DIV 1, GP ABCDEFG T4 / T6
DIP CL II, III, DIV 1, GP EFG T4/T6
IS CL I, II, III, DIV 1, GP ABCDEFG T4

CL I, Zone 0, AEx ia IIC T4
CL I, Zone 1, AEX ib IIC T4

• Permissible ambient temperature

T_a = T4: -40 ... +85 °C (-40 ... +185 °F)
T_a = T6: -40 ... +60 °C (-40 ... +140 °F)

• Entity parameters

According to "control drawing": A5E02189134N
U_m = 30 V, I_m = 100 mA,
P_i = 750 mW, L_i = 400 µH, C_i = 6 nF

• Marking (NI/NO)

NI CL I, DIV 2, GP ABCD T4/T6
NI CL I, Zone 2, GP IIC T4/T6
S CL II, III, GPFG T4/T6
NI CL I, DIV 2, GP ABCD T4/T6, NIFW
NI CL I, Zone 2, GP IIC T4/T6, NIFW
NI CLII, III, DIV 2, GP FG T4/T6, NIFW

• Permissible ambient temperature

T_a = T4: -40 ... +85 °C (-40 ... +185 °F)
T_a = T6: -40 ... +60 °C (-40 ... +140 °F)

• (NI/S) parameters

According to "control drawing": A5E02189134N
U_m = 45 V, L_i = 400 µH, C_i = 6 nF

Explosion protection for Canada

(according to _CCSA_US)

Certificate of Compliance

No. 2280963

• Marking (XP/DIP)

CL I, DIV 1, GP ABCD T4 /T6;
CL II, DIV 1, GP EFG T4/T6

• Permissible ambient temperature

T_a = T4: -40 ... +85 °C (-40 ... +185 °F)
T_a = T6: -40 ... +60 °C (-40 ... +140 °F)

• XD/DIP parameters

According to "control drawing":
A5E02189134N
U_m = 45 V

• Marking (ia/ib)

CL I, Ex ia/Ex ib IIC, T4
CL II, III, Ex ia/Ex ib, GP EFG, T4
CL I, AEx ia/AEx ib IIC, T4
CL II, III, AEx ia/ AEx ib, GP EFG, T4

• Permissible ambient temperature

T_a = T4: -40 ... +85 °C (-40 ... +185 °F)

• Entity parameters

U_i = 30 V, I_i = 100 mA, P_i = 750 mW, R_i = 300 О© , L_i = 400 µH, C_i = 6 nF

• Marking (NI/n)

CL I, DIV 2, GP ABCD T4/T6
CL II, III, DIV 2, GP FG T4/T6
Ex nA IIC T4/T6
AEx nA IIC T4/T6
Ex nL IIC T4/T6
AEx nL IIC T4/T6

• Permissible ambient temperature

T_a = T4: -40 ... +85 °C (-40 ... +185 °F)
T_a = T6: -40 ... +60 °C (-40 ... +140 °F)

• NI/nA parameters

According to "control drawing": A5E02189134N
U_m = 45 V

• nL parameters

According to "control drawing": A5E02189134N
U_i = 45 V, I_i = 100 mA, L_i = 400 µH, C_i = 6 nF

Explosion protection for China

(acc. to NEPSI)

• Intrinsic safety "i"

GYJ111111X

• Marking

Ex ia/ib IIB/IIC T4

• Permissible ambient temperature

-40 ... +85 °C (-40 ... +185 °F)

• Wiring

To certified intrinsically-safe circuits with the following peak values:
U_i = 30 V, I_i = 100 mA, P_i = 750 mW

• Effective internal inductance

L_i = 400 ОјH

• Effective internal capacitance

C_i = 6 nF

• Flameproof enclosure "d"

GYJ111112

• Marking

Ex dia IIC T4/T6

• Permissible ambient temperature

-40 ... +85 °C (-40 ... +185 °F) temperature class T4;
-40 ... +60 °C (-40 ... +140 °F) temperature class T6

• Wiring

To circuits with operating values: U_m = 10.5 ... 45 V DC

• Dust explosion protection for zone 21/22

GYJ111112

• Marking

DIP A21 T_A,T120 °C IP68 D21

• Wiring

To circuits with operating values: U_m = 10.5 ... 45 V DC

• Type of protection "n" (zone 2)

GYJ111111X

• Marking

Ex nL IIB/IIC T4/T6
Ex nA II T4/T6

• Wiring

U_i = 45 V DC

• Effective internal inductance

L_i = 400 ОјH

• Effective internal capacitance

C_i = 6 nF

Load with connection of

• HART communicator

R_B = 230 ... 1100 О©

• HART modem

R_B = 230 ... 500 О©

Cable

2-wire shielded: ≤ 3.0 km (1.86 miles),
multi-wired shielded: ≤ 1.5 km (0.93 miles)

Protocol

HART Version 6.0

PC/laptop requirements

IBM compatible, RAM > 32 MB,
hard disk > 70 MB, depending on modem type:
RS 232 interface or USB connection,
VGA graphics

Software for computer

SIMATIC PDM 6.0