General information

Product family

ET 200SP

Product category

Analog module input

Product type designation

ET 200SP, AI 2xSG 4/6-wire HS

Firmware version

V1.0.0

• FW update possible

Yes

Suitable BaseUnits

BU type A0

Color code for module-specific color-coded label

CC00

Product function

• I&M data

Yes, I&M0 to I&M3

• Measuring range scalable

No

• Measured values scalable

No

• Measuring range adaptation

Yes, +/- 0.5 mV/V to 320 mV/Volt

Engineering with

• STEP 7 TIA Portal can be configured/integrated as of version

V14 SP1

• STEP 7 can be configured/integrated as of version

V5.5 SP4 or higher

• PROFIBUS as of GSD version/GSD revision

GSD revision 5

• PROFINET as of GSD version/GSD revision

GSDML V2.32

Operating mode

• Oversampling

Yes, 2 channels per module

• MSI

No

CiR – Configuration in RUN

Parameter reassignment possible in RUN

Yes

Calibration possible in RUN

No

Installation type/mounting

Rack mounting

Yes

Front mounting

Yes

Rail mounting

Yes

Wall/direct mounting

No

Supply voltage

Type of supply voltage

DC

Rated value (DC)

24 V

Valid range, lower limit (DC)

19.2 V

Valid range, upper limit (DC)

28.8 V

Reverse polarity protection

Yes

Input current

Current consumption (rated value)

70 mA

Power loss

Typical power loss

1.2 W, without sensor supply

Address range

Address range per module, max.

32 bytes

Hardware configuration

BaseUnits for connection variants

• 4-wire connection

BU type A0

• 6-wire connection

BU type A0

Analog inputs

No. of analog inputs

2 differential inputs

Cycle time (all channels), min.

100 Ојs

Analog input with oversampling

Yes

• Values per cycle, max.

14

• Resolution, min.

100 Ојs

Standardization of measured values

Input ranges

• Voltage

Yes

Input ranges (rated values), voltages

•  -320 mV/V to +320 mV/V

16/28 bits

Cable length

• Shielded, max.

500 m (1 640.42 ft)

Generation of analog input values

Measuring principle

Sigma delta

Integration and conversion time/resolution per channel

• Resolution with overrange (bits including sign), max.

28 bits, 16 bits with oversampling

• Interference voltage suppression for interference frequency f1 in Hz

60 / 50 / off

• Conversion time (per channel)

100 Ојs

Measured value smoothing

• IIR low-pass filter ordinal

0.1 ... 6 553.5 Hz, adjustable

• Moving average value filter

0.1 ... 655.35 Hz, adjustable

• Notch filter

0.1 ... 1 000.0 Hz, adjustable

Encoders

Connection of sensors

• For voltage measurement

Yes

• Supply voltage

4.85 V DC, +/- 3%

• Resistance of full bridge strain gauge min.

80 ohms

• Resistance of full bridge strain gauge max.

5 000 ohms

Errors/accuracies

Linearity error (in relation to input range), (+/-)

≤ 0.025%

Temperature error (in relation to input range), (+/-) 6-wire connection

≤ 5 ppm/contactor relay

Temperature error (in relation to input range), (+/-) 4-wire connection

≤ 10 ppm/contactor relay

Temperature error zero point (+/-)

≤ 0.25 µV/contactor relay

Error limit according to DIN 1319-1 at 20 °C +/-10 K

• Voltage, related to input range, (+/-)

≤ 0.05 %

Isochronous mode

Isochronous mode (application synchronized up to terminal)

Yes

Filter and processing (TWE), min.

87 Ојs

Bus cycle time (TDP), min.

125 Ојs

Interrupts/diagnostics/status information

Interrupts

• Diagnostic interrupt

Yes

• Limit alarms

Yes, two high and two low limits

Diagnostic messages

• Monitoring of supply voltage

Yes

• Wire break

Yes

• Short circuit

Yes

• Group error

Yes

• Overflow/underflow

Yes

Diagnostics LED

• Monitoring of supply voltage (PWR LED)

Yes, green PWR LED

• Channel status display

Yes, green LED

• For channel diagnostics

Yes, red LED

• For module diagnostics

Yes, green/red DIAG LED

Galvanic isolation

Galvanic isolation of channels

• Between channels

No

• Between channels and backplane bus

Yes

• Between channels and electronics power supply

Yes

Insulation

Insulation tested with

707 V DC (type test)

Degree of protection and protection class

Degree of protection

IP20

Standards, approvals and certificates

Suitable for safety functions

No

Equipment designation according to DIN EN 81346-2

K

Use in hazardous areas

• Explosion protection category for gas

No

• Explosion protection category for dust

No

Ambient conditions

Ambient temperature in operation

• Horizontal mounting, min.

-25 °C

• Horizontal mounting, max.

-60 °C

• Vertical mounting, min.

-25 °C

• Vertical mounting, max.

-50 °C

Connections

Design of electrical connection

Push-in terminals

Dimensions

Width

15 mm

Height

73 mm

Depth

58 mm

Weight

Weight, approx.

45 g