Digital I/O modules . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на Digital I/O modules

| | | | | |

Article number	6DL1131-6GF00-0PK0	6DL1131-6BH00-0PH1	6DL1131-6DF00-0PK0	6DL1131-6TH00-0PH1
	ET 200SP HA, DI 8X230VAC	ET 200SP HA, DI 16X24VDC	ET 200SP HA, DI 8X24 ... 125VDC	ET 200SP HA, DI 16XNAMUR
General information
Product type designation	DI 8x230VAC HA	DI 16x24VDC HA	DI 8x24 ... 125 V DC HA	DI 16xNAMUR HA
HW functional status	FS01	FS01	FS01	FS01
Firmware version	V1.0	V1.0	V1.0	V1.0
в—Џ FW update possible	Yes	Yes	Yes	Yes
Usable terminal block	TB type K0	TB type H1 and M1	TB type K0	TB type H1 and M1
Color code for module-specific color identification plate	CC42	CC01	CC42	CC01
Product function
в—Џ I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
Engineering with
в—Џ PCS 7 configurable/integrated as of version	V9.0	V9.0	V9.0	V9.0
Operating mode
в—Џ DI	Yes	Yes	Yes	Yes
в—Џ Counter		No	No	No
в—Џ Oversampling		No	No
в—Џ MSI		No	No
Redundancy
в—Џ Redundancy capability	No	Yes; With TB type M1	No	Yes; With TB type M1
Supply voltage
Rated value (DC)		24 V	24 V	24 V
permissible range, lower limit (DC)		19.2 V	19.2 V	19.2 V
permissible range, upper limit (DC)		28.8 V	28.8 V	28.8 V
Rated value (AC)	230 V
Reverse polarity protection		Yes	Yes	Yes
Input current
Current consumption (rated value)		60 mA; without sensor supply	16 mA	95 mA
Current consumption, max.		120 mA; without sensor supply	20 mA	115 mA
Encoder supply
Number of outputs		16		16
Output voltage encoder supply, min.		18.2 V; L+ (-1 V)		8.1 V
Short-circuit protection		Yes; Electronic (response threshold 0.7 A to 1.3 A; for IO redundancy up to 2.6 A) Ensure sufficient low-resistance cable routing to the sensor/actuator in order to attain the response threshold. Depending on the cable cross-section used, there may be constraints regarding the usable length of cable.		Yes
Output current
в—Џ up to 60 °C, max.		2 A; 1 A when mounted vertically; see derating information in Equipment Manual
в—Џ up to 70 °C, max.		1 A; See derating information in Equipment Manual
24 V encoder supply
в—Џ 24 V		Yes
в—Џ Short-circuit protection		Yes; Electronic (response threshold 0.7 A to 1.3 A; for IO redundancy up to 2.6 A) Ensure sufficient low-resistance cable routing to the sensor/actuator in order to attain the response threshold. Depending on the cable cross-section used, there may be constraints regarding the usable length of cable.
Power
Power available from the backplane bus	105 mW	80 mW		74 mW
Power loss
Power loss, typ.	1.8 W; Active power, load voltage 230 V, all inputs connected with 230 V, 50 Hz	3.6 W; Maximum value (taking the max. encoder current and the max. operating voltage into account)	3.75 W	2.4 W
Address area
Address space per module
в—Џ Address space per module, max.	1 byte; + 1 byte for QI information	2 byte; + 2 bytes for QI information (additional 18 bytes when using high-precision time stamping)	1 byte; + 1 byte for QI information	2 byte; + 2 bytes for QI information
Hardware configuration
Automatic encoding
в—Џ Mechanical coding element	Yes	Yes
Digital inputs
Number of digital inputs	8; Isolated	16	8	16; NAMUR
Digital inputs, parameterizable		Yes		Yes
Source/sink input		Yes; P-reading	Yes; P-reading
Input characteristic curve in accordance with IEC 61131, type 1		Yes	Yes
Input characteristic curve in accordance with IEC 61131, type 2		No
Input characteristic curve in accordance with IEC 61131, type 3	Yes	Yes	Yes
Pulse extension		Yes		Yes; 0.5 s, 1 s, 2 s
в—Џ Length		Off, 50 ms, 100 ms, 200 ms, 500 ms, 1 s, 2 s
Time stamping		Yes; Resolution 10 ms	Yes; Resolution 10 ms	Yes
Time stamp (with precision of 1 ms)		Yes; Resolution 1ms	Yes; Resolution 1ms	No
Edge evaluation		Yes; rising edge, falling edge, edge change		Yes; rising edge, falling edge, edge change
Signal change flutter				Yes; 2 to 32 signal changes
Flutter observation window				Yes; 0.5 s, 1 s to 100 s in 1-s steps
Input voltage
в—Џ Type of input voltage	120/230 V AC (47 Hz to 63 Hz)	DC	DC	DC
в—Џ Rated value (DC)		24 V		8.2 V
в—Џ Rated value (AC)	230 V
в—Џ for signal "0"	0V AC to 40V AC	-30 to +5V	-125 ... +5 V
в—Џ for signal "1"	74 V AC to 264 V AC	+11 to +30V	+11 ... +125 V
Input current
в—Џ for signal "1", typ.	10.8 mA	2.5 mA	3.1 mA
for 10 k switched contact
вЂ” for signal "0"				0.35 to 1.2 mA
вЂ” for signal "1"				2.1 ... 6.4 mA
for unswitched contact
вЂ” for signal "0", max. (permissible quiescent current)				0.5 mA
вЂ” for signal "1"				typ. 8 mA
for NAMUR encoders
вЂ” for signal "0"				0.35 to 1.2 mA
вЂ” for signal "1"				2.1 ... 6.4 mA
Input delay (for rated value of input voltage)
в—Џ tolerated changeover time for changeover contacts				300 ms
for standard inputs
вЂ” parameterizable		Yes; none / 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms	Yes; 0.05 / 0.1 / 0.4 / 0.8 / 1.6 / 3.2 / 12.8 / 20 ms (in each case + delay of 30 to 500 µs, depending on line length)
вЂ” at "0" to "1", min.	1.5 ms
вЂ” at "0" to "1", max.	4 ms
вЂ” at "1" to "0", min.	10 ms
вЂ” at "1" to "0", max.	10 ms
for NAMUR inputs
вЂ” at "0" to "1", max.				17 ms
вЂ” at "1" to "0", max.				25 ms
Cable length
в—Џ shielded, max.	1 000 m	1 000 m	1 000 m	600 m
в—Џ unshielded, max.	600 m	600 m	600 m	200 m
Encoder
Connectable encoders
в—Џ NAMUR encoder/changeover contact according to EN 60947				Yes
в—Џ Single contact / changeover contact unconnected				Yes
в—Џ Single contact / changeover contact connected with 10 kО©				Yes
в—Џ 2-wire sensor	Yes	Yes	Yes	Yes; Acc. to NAMUR
вЂ” permissible quiescent current (2-wire sensor), max.		1.5 mA	1.5 mA	1.2 mA
Interrupts/diagnostics/status information
Diagnostics function		Yes
Alarms
в—Џ Diagnostic alarm	Yes	Yes; channel by channel	Yes	Yes; channel by channel
в—Џ Hardware interrupt		Yes; channel by channel	Yes; Parameterizable, channels 0 to 7, rising/falling edge	Yes; Parameterizable, channels 0 to 15, rising/falling edge
Diagnostic messages
в—Џ Diagnostic information readable	Yes	Yes	Yes	Yes
в—Џ Monitoring the supply voltage		Yes; Module-wise	Yes	Yes
вЂ” parameterizable		Yes		Yes
в—Џ Monitoring of encoder power supply		Yes		Yes
в—Џ Wire-break		Yes; Channel-by-channel, optional protective circuit for preventing wire-break diagnostics in the case of simple encoder contacts: 15 kOhm to 18 kOhm	Yes; channel by channel	Yes
в—Џ Short-circuit				Yes
в—Џ Short-circuit to M		Yes; Encoder supply to M, channel by channel
в—Џ Group error			Yes	Yes
в—Џ Changeover contact error				Yes
Diagnostics indication LED
в—Џ MAINT LED	Yes; yellow LED	Yes; yellow LED	Yes; yellow LED	Yes; yellow LED
в—Џ Monitoring of the supply voltage (PWR-LED)		Yes; green PWR LED	Yes; green PWR LED	Yes; green PWR LED
в—Џ Channel status display	Yes; Green LED	Yes; Green LED	Yes; Green LED	Yes; Green LED
в—Џ for channel diagnostics		Yes; Red LED	Yes; Red LED	Yes; Red LED
в—Џ for module diagnostics	Yes; green/red DIAG LED	Yes; Green/red LED	Yes; green/red DIAG LED	Yes; green/red DIAG LED
Potential separation
Potential separation channels
в—Џ between the channels	Yes	No	No	No
в—Џ between the channels, in groups of	2
в—Џ between the channels and backplane bus	Yes	Yes	Yes	Yes
в—Џ Between the channels and load voltage L+				Yes
в—Џ between the channels and the power supply of the electronics		No
Permissible potential difference
between different circuits	Between channels: 230 V AC (same system phase) / 120 V AC (different system phase); between groups: 230 V AC (different system phase)		250 V AC/300 V DC
between channels and backplane bus/supply voltage	230 V AC
Isolation
Isolation tested with		1 500 V DC/1 min, type test	3 500 V DC/1 min, type test	1 500 V DC/1 min, type test
tested with
в—Џ between channels and backplane bus/supply voltage	4 200 V DC/1 min, type test
Ambient conditions
Ambient temperature during operation
в—Џ horizontal installation, min.	-40 °C	-40 °C	-40 °C	-40 °C
в—Џ horizontal installation, max.	70 °C	70 °C	70 °C	70 °C
в—Џ vertical installation, min.	-40 °C	-40 °C	-40 °C	-40 °C
в—Џ vertical installation, max.	60 °C	60 °C	60 °C	60 °C
Dimensions
Width	22.5 mm	22.5 mm	22.5 mm	22.5 mm
Height	115 mm	115 mm	115 mm	115 mm
Depth	138 mm	138 mm	138 mm	138 mm
Weights
Weight, approx.	148 g	135 g	165 g	153 g

Article number	6DL1132-6BH00-0PH1	6DL1132-6HD50-0PK0
	ET 200SP HA, DQ 16X24VDC/0,5A	ET 200SP HA, RQ 4X120VDC-230VAC/5A CO
General information
Product type designation	DQ 16x24VDC/0.5A HA	RQ 4x120 V UC ... 230 V AC/5 A CO HA
HW functional status	FS01	FS01
Firmware version	V1.0	V1.0
в—Џ FW update possible	Yes	Yes
Usable terminal block	TB type H1 and M1	TB type K0
Color code for module-specific color identification plate	CC02	CC40
Product function
в—Џ I&M data	Yes; I&M0 to I&M3	Yes; I&M0 to I&M3
Engineering with
в—Џ PCS 7 configurable/integrated as of version	V9.0	V9.0
Operating mode
в—Џ DQ	Yes
в—Џ DQ with energy-saving function	No
в—Џ PWM	No
в—Џ Oversampling	No
в—Џ MSO	No
Redundancy
в—Џ Redundancy capability	Yes; With TB type M1	No
Supply voltage
Rated value (DC)	24 V	24 V
permissible range, lower limit (DC)	19.2 V	19.2 V
permissible range, upper limit (DC)	28.8 V	28.8 V
Reverse polarity protection	Yes	Yes
Input current
Current consumption (rated value)	60 mA; without load	50 mA; At 24 V and energized changeover coils
Current consumption, max.	70 mA; without load	60 mA; At 19.2 V and energized changeover coils
Output voltage
Rated value (DC)	24 V
Power loss
Power loss, typ.	1.2 W; minimum - typ. specification not possible because load-dependent	2.8 W; At 24 V, energized changeover coils and 5 A current across each changeover contact
Address area
Address space per module
в—Џ Address space per module, max.	2 byte; + 2 bytes for QI information	1 byte; + 1 byte for QI information
Digital outputs
Number of digital outputs	16	4
Current-sinking	No
Current-sourcing	Yes
Short-circuit protection	Yes; Ensure sufficient low-resistance cable routing to the sensor/actuator in order to attain the response threshold. Depending on the cable cross-section used, there may be constraints regarding the usable length of cable.
в—Џ Response threshold, typ.	0.7 A to 1.3 A (for IO redundancy up to max 2.6 A)
Open-circuit detection	Yes; 0.7 mA test current for wire-break diagnostics; this value is doubled in the case of IO redundancy
Overload protection	Yes
Limitation of inductive shutdown voltage to	L+ -(37 to 41V)
Controlling a digital input	Yes
Switching capacity of the outputs
в—Џ with resistive load, max.	0.5 A
в—Џ on lamp load, max.	5 W
Load resistance range
в—Џ lower limit	48 в„¦
в—Џ upper limit	12 kв„¦
Output current
в—Џ for signal "1" rated value	0.5 A
в—Џ for signal "0" residual current, max.	0.7 mA; Test current for wire-break diagnostics; this value is doubled in the case of IO redundancy
Output delay with resistive load
в—Џ "0" to "1", typ.	50 µs
в—Џ "1" to "0", typ.	100 µs
Parallel switching of two outputs
в—Џ for uprating	No
в—Џ for redundant control of a load	Yes
Switching frequency
в—Џ with resistive load, max.	100 Hz	2 Hz
в—Џ with inductive load, max.	2 Hz	0.5 Hz
в—Џ on lamp load, max.	10 Hz	2 Hz
Total current of the outputs
в—Џ Current per channel, max.	0.5 A	5 A
в—Џ Current per module, max.	8 A	20 A
Total current of the outputs (per module)
horizontal installation
вЂ” up to 30 °C, max.	8 A
вЂ” up to 40 °C, max.	8 A
вЂ” up to 50 °C, max.	8 A
вЂ” up to 60 °C, max.	5.5 A
вЂ” up to 70 °C, max.	3 A	20 A
vertical installation
вЂ” up to 30 °C, max.	8 A
вЂ” up to 40 °C, max.	6.33 A
вЂ” up to 50 °C, max.	4.67 A
вЂ” up to 60 °C, max.	3 A	20 A
Relay outputs
в—Џ Number of relay outputs		4
в—Џ external protection for relay outputs		yes; 6 A, see data in manual
Switching capacity of contacts
вЂ” with inductive load, max.		2 A; 2 A (24 V DC), 0.5 A (60 V DC), 0.1 A (120 V DC)
вЂ” with resistive load, max.		5 A; 5 A (30 V DC), 5 A (230 V AC)
вЂ” Switching current, min.		8 mA
вЂ” Rated switching voltage (DC)		24 V; 24 V DC to 120 V DC
вЂ” Rated switching voltage (AC)		230 V; 24V AC to 230V AC
Cable length
в—Џ shielded, max.	1 000 m	1 000 m
в—Џ unshielded, max.	600 m	200 m
Interrupts/diagnostics/status information
Diagnostics function	Yes	Yes
Substitute values connectable	Yes	Yes
Alarms
в—Џ Diagnostic alarm	Yes	Yes
Diagnostic messages
в—Џ Monitoring the supply voltage	Yes	Yes
вЂ” parameterizable		Yes
в—Џ Wire-break	Yes; channel by channel
в—Џ Short-circuit to M	Yes; channel by channel
в—Џ Short-circuit to L+	Yes; channel by channel
в—Џ Group error	Yes
Diagnostics indication LED
в—Џ MAINT LED	Yes; yellow LED	Yes; yellow LED
в—Џ Monitoring of the supply voltage (PWR-LED)	Yes; green PWR LED	Yes; green PWR LED
в—Џ Channel status display	Yes; Green LED	Yes; Green LED
в—Џ for channel diagnostics	Yes; Red LED
в—Џ for module diagnostics	Yes; green/red DIAG LED	Yes; green/red DIAG LED
Potential separation
Potential separation channels
в—Џ between the channels	No	Yes
в—Џ between the channels and backplane bus	Yes	Yes
в—Џ Between the channels and load voltage L+		Yes
Permissible potential difference
between different circuits		Between channels: 230 V AC (different system phase)
between channels and backplane bus/supply voltage		230 V AC
Isolation
Isolation tested with	1 500 V DC/1 min, type test
tested with
в—Џ between channels and backplane bus/supply voltage		4 200 V DC/1 min, type test
в—Џ between backplane bus and supply voltage		1 500 V DC/1 min, type test
Ambient conditions
Ambient temperature during operation
в—Џ horizontal installation, min.	-40 °C	-40 °C; No icing
в—Џ horizontal installation, max.	70 °C	70 °C
в—Џ vertical installation, min.	-40 °C	-40 °C; No icing
в—Џ vertical installation, max.	60 °C	60 °C
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude		3 000 m due to converter type used
Dimensions
Width	22.5 mm	22.5 mm
Height	115 mm	115 mm
Depth	138 mm	138 mm
Weights
Weight, approx.	137 g	162 g

skener.ru

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
Бесконтактные выключатели Конечные выключатели Оптические датчики Энкодеры

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FS - Установка умягчения

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FK - Установка обезжелезивания