Motor protection

Motor protection with PTC thermistors with 1 (for motors 1LE10 FS 80 and 90) or 3 embedded temperature sensors for tripping

A11

Motor protection with PTC thermistors with 6 embedded temperature sensors for alarm and tripping

A12

Motor temperature detection with embedded temperature sensor KTY 84-130

A23

Motor temperature detection with embedded temperature sensors 2 x KTY 84‑130

A25

Temperature detectors for tripping

A31

Installation of 3 PT100 resistance thermometers

A60

Motor connection and connection box

ECOFAST motor connector Han-Drive 10e for 230 VО”/400 VY

G55

ECOFAST motor connector EMC Han-Drive 10e for 230 VО”/400 VY

G56

Connection box on RHS

K09

Connection box on LHS

K10

One metal cable gland

K54

Cable gland, max. configuration

K55

Rotation of the connection box through 90°, entry from DE

K83

Rotation of the connection box through 90°, entry from NDE

K84

Rotation of the connection box through 180°

K85

Next larger connection box

L00

External grounding

L13

3 cables protruding, 0.5 m long

L44

3 cables protruding, 1.5 m long

L45

6 cables protruding, 0.5 m long

L47

6 cables protruding, 1.5 m long

L48

6 cables protruding, 3 m long

L49

Connection box on NDE

M64

Terminal strip for main and auxiliary terminals

M69

Windings and insulation

Temperature class 155 (F), used acc. to 155 (F), with service factor (SF)

C11

Temperature class 155 (F), used acc. to 155 (F), with increased output

C12

Temperature class 155 (F), used acc. to 155 (F), with increased coolant

temperature

C13

Temperature class 180 (H) at rated output and max. CT 60 °C

C18

Increased air humidity/ temperature with 30 to 60 g water per m³ of air

C19

Temperature class 155  (F), used acc. to 130  (B), coolant temperature 45 °C, derating approx. 4 %

C22

Temperature class 155  (F), used acc. to 130  (B), coolant temperature 50 °C, derating approx. 8 %

C23

Temperature class 155  (F), used acc. to 130  (B), coolant temperature 55 °C, derating approx. 13 %

C24

Temperature class 155  (F), used acc. to 130  (B), coolant temperature 60 °C, derating approx.18 %

C25

Increased air humidity/ temperature with 60 to 100 g water per m³ of air

C26

Temperature class 155  (F), used acc. to 130  (B), with higher coolant temperature and/or site altitude

Y50 вЂў and specified output, CT .. °C or SA  вЂ¦. m above sea level

Temperature class 155  (F), used acc. to 155  (F), other requirements

Y52 вЂў and specified output, CT .. °C or SA  вЂ¦. m above sea level

Colors and paint finish

Special finish in RAL 7030 stone gray

–

Special finish in other standard RAL colors

Y54 вЂў and special finish RAL вЂ¦.

Special finish in special RAL colors

Y51 вЂў and special finish RAL вЂ¦.

Special finish sea air resistant

M94

Unpainted (only cast-iron parts primed)

K23

Unpainted, only primed

K24

Modular technology – Basic versions

Mounting of separately driven fan

G17

Mounting of brake

G26

Mounting of 1XP8001-1 (HTL) rotary pulse encoder

H57

Mounting of 1XP8001-2 (TTL) rotary pulse encoder

H58

Modular technology – Combinations of basic versions

Mounting of separately driven fan and 1XP8001-1 rotary pulse encoder

H61

Mounting of brake and 1XP8001-1 rotary pulse encoder

H62

Mounting of brake and separately driven fan

H63

Mounting of brake, separately driven fan and 1XP8001-1 rotary pulse encoder

H64

Mounting of separately driven fan and 1XP8001-2 rotary pulse encoder

H97

Mounting of brake and 1XP8001-2 rotary pulse encoder

H98

Mounting of brake, separately driven fan and 1XP8001-2 rotary pulse Encoder

H99

Modular technology – Additional versions

Brake supply voltage 24 V DC

C00

Brake supply voltage 400 V AC

C01

Brake supply voltage 180 V DC, for operation on MICROMASTER 411-ECOFAST

C02

Mechanical manual brake release with lever (no locking)

K82

Special technology

Prepared for mounting of MMI

H15

Mounting of LL 861 900 220 rotary pulse encoder

H70

Mounting of HOG 9 D 024 I rotary pulse encoder

H72

Mounting of HOG 10 D 1024 I rotary pulse encoder

H73

Prepared for mounting of LL 861 900 220

H78

Prepared for mounting of HOG 9 D 1024 I

H79

Prepared for mounting of HOG 10 D 1024 I

H80

Mechanical design and degrees of protection

Drive-end seal for flangemounting motors, oil-tight to 0.1 bar

K17

With two additional eyebolts for IM V1/IM V3

K32

Low-noise version for 2-pole motors with clockwise direction of rotation

K37

Low-noise version for 2-pole motors with counterclockwise direction of rotation

K38

IP65 degree of protection

K50

IP56 degree of protection

K52

Vibration-proof version

L03

Condensation drainage holes

L12

Rust-resistant screws (externally)

M27

Mechanical protection for encoder

M68

Coolant temperature and site altitude

Coolant temperature –40 to +40 °C

D03

Coolant temperature –30 to +40 °C

D04

Designs in accordance with standards and specifications

CCC China Compulsory Certification

D01

IE1 motor without CE marking for export outside EEA (see EU Directive 640/2009)

D22

New!

Electrical according to NEMA MG1-12

D30

Design according to UL with "Recognition Mark

D31

Certified for Korea acc. to KS C4202

D33

China Energy Efficiency Label

D34

New!

Canadian regulations (CSA)

D40

NEMA Energy Efficient, North America version according to NEMA MG1, Table 12-11, incl. UL and CSA

D42

New!

PSE mark for Japan

D46

VIK version

K30

Ex nA II on VIK rating plate

C27

Bearings and lubrication

Measuring nipple for SPM shock pulse measurement for bearing inspection

G50

Bearing design for increased cantilever forces

K20

Regreasing device

K40

Located bearing DE

K94

Located bearing NDE

L04

Balance and vibration quantity

Vibration quantity level A

–

Vibration quantity level B

K02

Full-key balancing

L68

Balancing without key

M37

Shaft and rotor

Concentricity of shaft extension, coaxiality and linear movement in accordance with DIN 42955 Tolerance R for flange-mounting motors

K04

Second standard shaft extension

K16

Shaft extension with standard dimensions, without feather keyway

K42

Concentricity of shaft extension in accordance with DIN 42955 Tolerance R

L39

Standard shaft made of stainless steel

M65

Non-standard cylindrical shaft extension

Y55 вЂў and identification code

Heating and ventilation

Fan cover for textile industry

H17

Metal external fan

K35

Anti-condensation heating for 230 V

K45

Anti-condensation heating for 115 V

K46

Rating plate and extra rating plates

Second lubrication plate, loose

B06

Extra rating plate for voltage tolerance

B07

New!

Second rating plate, loose

K31

Rating plate, stainless steel

M40

New!

Extra rating plate or rating plate with deviating rating plate data

Y80 вЂў and identification code

Extra rating plate with identification codes

Y82 вЂў and identification code

Additional information on rating plate and on package label (max. 20 characters)

Y84 вЂў and identification code

Packaging, safety notes, documentation and test certificates

With one safety and start-up guide per box pallet

B01

Acceptance test certificate 3.1 in acc. with EN 10204

B02

Printed German/English Operating Instructions (Compact) enclosed

–

Printed German/English Operating Instructions enclosed

B23

Type test with heat run for horizontal motors, with acceptance

F83

Wire-lattice pallet

L99

Connected in star for dispatch

M32

Connected in delta for dispatch

M33