SIPLUS ET 200S fail-safe electronic modules . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS ET 200S fail-safe electronic modules

| | | |

Article number		6AG1138-4FA05-2AB0
		SIPLUS ET200S EM F-DI 24V Profisafe
Supply voltage
Rated value (DC)
в—Џ 24 V DC		Yes
Encoder supply
Number of outputs		2
Type of output voltage		min. L+ (-1.5 V)
Short-circuit protection		Yes; Electronic (response threshold 0.7 A to 1.8 A)
Output current
в—Џ Rated value		300 mA
в—Џ permissible range, lower limit		0 mA
в—Џ permissible range, upper limit		300 mA
Power loss
Power loss, typ.		4 W
Address area
Occupied address area
в—Џ Inputs		6 byte
в—Џ Outputs		4 byte
Digital inputs
Number of digital inputs		8; 8 (one-channel); 4 (two-channel)
Input characteristic curve in accordance with IEC 61131, type 1		Yes
Number of simultaneously controllable inputs
в—Џ Number of simultaneously controllable inputs		8
Input voltage
в—Џ Type of input voltage		DC
в—Џ Rated value (DC)		24 V
Input current
в—Џ for signal "1", typ.		3.7 mA
Input delay (for rated value of input voltage)
for standard inputs
вЂ” parameterizable		Yes
вЂ” at "0" to "1", min.		0.3 ms
вЂ” at "0" to "1", max.		17 ms
вЂ” at "1" to "0", min.		0.3 ms
вЂ” at "1" to "0", max.		17 ms
Cable length
в—Џ shielded, max.		500 m
в—Џ unshielded, max.		500 m
Encoder
Connectable encoders
в—Џ 2-wire sensor		No
вЂ” permissible quiescent current (2-wire sensor), max.		0.6 mA; max.
Interrupts/diagnostics/status information
Diagnostic functions		Yes
Alarms
в—Џ Diagnostic alarm		Yes
Diagnostic messages
в—Џ Diagnostic information readable		Yes
в—Џ Short-circuit		Yes
Diagnostics indication LED
в—Џ Group error SF (red)		Yes
в—Џ Status indicator digital input (green)		Yes
Potential separation
Potential separation digital inputs
в—Џ between the channels		No
в—Џ between the channels and backplane bus		Yes
в—Џ Between the channels and load voltage L+		No
Standards, approvals, certificates
Highest safety class achievable in safety mode
в—Џ acc. to EN 954		4
в—Џ Performance level according to ISO 13849-1		PLe
в—Џ SIL acc. to IEC 61508		SIL 2 (single-channel), SIL 3 (two-channel)
Ambient conditions
Ambient temperature during operation
в—Џ min.		-25 °C
в—Џ max.		60 °C
в—Џ At cold restart, min.		-25 °C
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3		Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width		30 mm
Height		81 mm
Depth		52 mm
Weights
Weight, approx.		78 g

Article number		6AG1138-4FB04-2AB0
		SIPLUS ET200S EM F-DO 24V Profisafe
Supply voltage
Load voltage L+
в—Џ Rated value (DC)		24 V
в—Џ Reverse polarity protection		No
Input current
From load voltage L+ (no load), typ.		100 mA
from backplane bus 3.3 V DC, max.		28 mA
Power loss
Power loss, typ.		3.5 W
Digital outputs
Number of digital outputs		4
Short-circuit protection		Yes
Limitation of inductive shutdown voltage to		Typ. (2L+) -47 V
Controlling a digital input		No
Switching capacity of the outputs
в—Џ on lamp load, max.		10 W
Load resistance range
в—Џ lower limit		12 в„¦
в—Џ upper limit		1 kв„¦
Output voltage
в—Џ for signal "1", min.		L+ (-2,0 V), current sourcing switch: L+ (-1,5 V), voltage drop on current sinking switch: max. 0.5 V
Output current
в—Џ for signal "1" rated value		2 A
в—Џ for signal "1" permissible range, min.		20 mA
в—Џ for signal "1" permissible range, max.		2.4 A
в—Џ for signal "0" residual current, max.		0.5 mA; Current-sourcing and current-sinking switches
Parallel switching of two outputs
в—Џ for uprating		No
в—Џ for redundant control of a load		No
Switching frequency
в—Џ with resistive load, max.		30 Hz; Symmetrical
в—Џ with inductive load, max.		0.1 Hz; Symmetrical
в—Џ on lamp load, max.		10 Hz; Symmetrical
Total current of the outputs
в—Џ Current per module, max.		6 A
Total current of the outputs (per group)
horizontal installation
вЂ” up to 40 °C, max.		6 A
вЂ” up to 55 °C, max.		5 A
вЂ” up to 60 °C, max.		4 A
vertical installation
вЂ” up to 40 °C, max.		4 A
Cable length
в—Џ shielded, max.		500 m
в—Џ unshielded, max.		500 m
Interrupts/diagnostics/status information
Diagnostic functions		Yes
Diagnostic messages
в—Џ Wire-break		Yes
в—Џ Short-circuit		Yes
Diagnostics indication LED
в—Џ Group error SF (red)		Yes
в—Џ Status indicator digital output (green)		Yes
Potential separation
Potential separation digital outputs
в—Џ between the channels		No
в—Џ between the channels and backplane bus		Yes
в—Џ Between the channels and load voltage L+		No
Isolation
tested with
в—Џ Load voltage L+ against backplane bus		2 545 V DC
Standards, approvals, certificates
Highest safety class achievable in safety mode
в—Џ acc. to EN 954		4
в—Џ Performance level according to ISO 13849-1		PLe
в—Џ SIL acc. to IEC 61508		SIL 3
Ambient conditions
Ambient temperature during operation
в—Џ min.		-25 °C
в—Џ max.		60 °C
в—Џ At cold restart, min.		-25 °C
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request
вЂ” to chemically active substances according to EN 60721-3-3		Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width		30 mm
Height		81 mm
Depth		52 mm
Weights
Weight, approx.		85 g