SIPLUS S7-300 CPU 315F-2 PN/DP . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS S7-300 CPU 315F-2 PN/DP

| | | | | | |

Article number	6AG1315-2FJ14-2AB0	6AG1315-2FJ14-2AY0
	SIPLUS S7-300 CPU315F-2PN/DP	SIPLUS S7-300 CPU315F-2PN/DP EN50155
General information
HW functional status	01	01
Firmware version	V3.2	V3.2
Engineering with
в—Џ Programming package	STEP 7 V5.5 or higher, Distributed Safety V5.4 SP4	STEP 7 V5.5 or higher, Distributed Safety V5.4 SP4
Supply voltage
Rated value (DC)
в—Џ 24 V DC	Yes	Yes; A power supply according to EN 50155 shall be used
permissible range, lower limit (DC)	20.4 V	20.4 V
permissible range, upper limit (DC)	28.8 V	28.8 V
external protection for power supply lines (recommendation)	2 A min.	2 A min.
Mains buffering
в—Џ Mains/voltage failure stored energy time	5 ms	5 ms
в—Џ Repeat rate, min.	1 s	1 s
Input current
Current consumption (rated value)	750 mA	750 mA
Current consumption (in no-load operation), typ.	150 mA	150 mA
Inrush current, typ.	4 A	4 A
IІt	1 AІ·s	1 AІ·s
Power loss
Power loss, typ.	4.65 W	4.65 W
Memory
Work memory
в—Џ integrated	512 kbyte	512 kbyte
в—Џ expandable	No	No
в—Џ Size of retentive memory for retentive data blocks	128 kbyte	128 kbyte
Load memory
в—Џ Plug-in (MMC)	Yes	Yes
в—Џ Plug-in (MMC), max.	8 Mbyte	8 Mbyte
в—Џ Data management on MMC (after last programming), min.	10 y	10 y
Backup
в—Џ present	Yes; Guaranteed by MMC (maintenance-free)	Yes; Guaranteed by MMC (maintenance-free)
в—Џ without battery	Yes; Program and data	Yes; Program and data
CPU processing times
for bit operations, typ.	0.05 µs	0.05 µs
for word operations, typ.	0.09 µs	0.09 µs
for fixed point arithmetic, typ.	0.12 µs	0.12 µs
for floating point arithmetic, typ.	0.45 µs	0.45 µs
CPU-blocks
Number of blocks (total)	1 024; (DBs, FCs, FBs); the maximum number of loadable blocks can be reduced by the MMC used.	1 024; (DBs, FCs, FBs); the maximum number of loadable blocks can be reduced by the MMC used.
DB
в—Џ Number, max.	1 024; Number range: 1 to 16000	1 024; Number range: 1 to 16000
в—Џ Size, max.	64 kbyte	64 kbyte
FB
в—Џ Number, max.	1 024; Number range: 0 to 7999	1 024; Number range: 0 to 7999
в—Џ Size, max.	64 kbyte	64 kbyte
FC
в—Џ Number, max.	1 024; Number range: 0 to 7999	1 024; Number range: 0 to 7999
в—Џ Size, max.	64 kbyte	64 kbyte
OB
в—Џ Size, max.	64 kbyte	64 kbyte
в—Џ Number of free cycle OBs	1; OB 1	1; OB 1
в—Џ Number of time alarm OBs	1; OB 10	1; OB 10
в—Џ Number of delay alarm OBs	2; OB 20, 21	2; OB 20, 21
в—Џ Number of cyclic interrupt OBs	4; OB 32, 33, 34, 35	4; OB 32, 33, 34, 35
в—Џ Number of process alarm OBs	1; OB 40	1; OB 40
в—Џ Number of DPV1 alarm OBs	3; OB 55, 56, 57	3; OB 55, 56, 57
в—Џ Number of isochronous mode OBs	1; OB 61	1; OB 61
в—Џ Number of startup OBs	1; OB 100	1; OB 100
в—Џ Number of asynchronous error OBs	6; OB 80, 82, 83, 85, 86, 87 (OB83 only for PROFINET IO)	6; OB 80, 82, 83, 85, 86, 87 (OB83 only for PROFINET IO)
в—Џ Number of synchronous error OBs	2; OB 121, 122	2; OB 121, 122
Nesting depth
в—Џ per priority class	16	16
в—Џ additional within an error OB	4	4
Counters, timers and their retentivity
S7 counter
в—Џ Number	256	256
Retentivity
вЂ” adjustable	Yes	Yes
вЂ” lower limit	0	0
вЂ” upper limit	255	255
вЂ” preset	Z 0 to Z 7	Z 0 to Z 7
Counting range
вЂ” can be set	Yes	Yes
вЂ” lower limit	0	0
вЂ” upper limit	999	999
IEC counter
в—Џ Number	Unlimited (limited only by RAM capacity)	Unlimited (limited only by RAM capacity)
S7 times
в—Џ Number	256	256
Retentivity
вЂ” adjustable	Yes	Yes
вЂ” lower limit	0	0
вЂ” upper limit	255	255
вЂ” preset	No retentivity	No retentivity
Time range
вЂ” lower limit	10 ms	10 ms
вЂ” upper limit	9 990 s	9 990 s
IEC timer
в—Џ present	Yes	Yes
в—Џ Type	SFB	SFB
в—Џ Number	Unlimited (limited only by RAM capacity)	Unlimited (limited only by RAM capacity)
Data areas and their retentivity
retentive data area in total	All, 128 KB max.	All, 128 KB max.
Flag
в—Џ Number, max.	2 048 byte	2 048 byte
в—Џ Retentivity available	Yes; MB 0 to MB 2047	Yes; MB 0 to MB 2047
в—Џ Retentivity preset	MB 0 to MB 15	MB 0 to MB 15
в—Џ Number of clock memories	8; 1 memory byte	8; 1 memory byte
Data blocks
в—Џ Retentivity adjustable	Yes; via non-retain property on DB	Yes; via non-retain property on DB
в—Џ Retentivity preset	Yes	Yes
Local data
в—Џ per priority class, max.	32 768 byte; Max. 2048 bytes per block	32 768 byte; Max. 2048 bytes per block
Address area
I/O address area
в—Џ Inputs	2 048 byte	2 048 byte
в—Џ Outputs	2 048 byte	2 048 byte
of which distributed
вЂ” Inputs	2 048 byte	2 048 byte
вЂ” Outputs	2 048 byte	2 048 byte
Process image
в—Џ Inputs	2 048 byte	2 048 byte
в—Џ Outputs	2 048 byte	2 048 byte
в—Џ Inputs, adjustable	2 048 byte	2 048 byte
в—Џ Outputs, adjustable	2 048 byte	2 048 byte
в—Џ Inputs, default	128 byte	128 byte
в—Џ Outputs, default	128 byte	128 byte
Subprocess images
в—Џ Number of subprocess images, max.	1; With PROFINET IO, the length of the user data is limited to 1600 bytes	1; With PROFINET IO, the length of the user data is limited to 1600 bytes
Digital channels
в—Џ Inputs	16 384	16 384
вЂ” of which central	1 024	1 024
в—Џ Outputs	16 384	16 384
вЂ” of which central	1 024	1 024
Analog channels
в—Џ Inputs	1 024	1 024
вЂ” of which central	256	256
в—Џ Outputs	1 024	1 024
вЂ” of which central	256	256
Hardware configuration
Number of expansion units, max.	3	3
Number of DP masters
в—Џ integrated	1	1
в—Џ via CP	4	4
Number of operable FMs and CPs (recommended)
в—Џ FM	8	8
в—Џ CP, PtP	8	8
в—Џ CP, LAN	10	10
Rack
в—Џ Racks, max.	4	4
в—Џ Modules per rack, max.	8	8
Time of day
Clock
в—Џ Hardware clock (real-time)	Yes	Yes
в—Џ retentive and synchronizable	Yes	Yes
в—Џ Backup time	6 wk; At 40 °C ambient temperature	6 wk; At 40 °C ambient temperature
в—Џ Deviation per day, max.	10 s; Typ.: 2 s	10 s; Typ.: 2 s
в—Џ Behavior of the clock following POWER-ON	Clock continues running after POWER OFF	Clock continues running after POWER OFF
в—Џ Behavior of the clock following expiry of backup period	Clock continues to run with the time at which the power failure occurred	Clock continues to run with the time at which the power failure occurred
Operating hours counter
в—Џ Number	1	1
в—Џ Number/Number range	0	0
в—Џ Range of values	0 to 2^31 hours (when using SFC 101)	0 to 2^31 hours (when using SFC 101)
в—Џ Granularity	1 hour	1 hour
в—Џ retentive	Yes; Must be restarted at each restart	Yes; Must be restarted at each restart
Clock synchronization
в—Џ supported	Yes	Yes
в—Џ to MPI, master	Yes	Yes
в—Џ to MPI, slave	Yes	Yes
в—Џ to DP, master	Yes; With DP slave only slave clock	Yes; With DP slave only slave clock
в—Џ to DP, slave	Yes	Yes
в—Џ in AS, master	Yes	Yes
в—Џ in AS, slave	Yes	Yes
в—Џ on Ethernet via NTP	Yes; As client	Yes; As client
Digital inputs
Number of digital inputs	0	0
Digital outputs
Number of digital outputs	0	0
Analog inputs
Number of analog inputs	0	0
Analog outputs
Number of analog outputs	0	0
Interfaces
Number of industrial Ethernet interfaces	1	1
Number of PROFINET interfaces	1	1
Number of RS 485 interfaces	1	1
Number of RS 422 interfaces	0	0
1. Interface
Interface type	Integrated RS 485 interface	Integrated RS 485 interface
Physics	RS 485	RS 485
Isolated	Yes	Yes
Power supply to interface (15 to 30 V DC), max.	200 mA	200 mA
Functionality
в—Џ MPI	Yes	Yes
в—Џ PROFIBUS DP master	Yes	Yes
в—Џ PROFIBUS DP slave	Yes	Yes
в—Џ Point-to-point connection	No	No
MPI
в—Џ Transmission rate, max.	12 Mbit/s	12 Mbit/s
Services
вЂ” PG/OP communication	Yes	Yes
вЂ” Routing	Yes	Yes
вЂ” Global data communication	Yes	Yes
вЂ” S7 basic communication	Yes	Yes
вЂ” S7 communication	Yes	Yes
вЂ” S7 communication, as client	No; but via CP and loadable FB	No; but via CP and loadable FB
вЂ” S7 communication, as server	Yes	Yes
DP master
в—Џ Transmission rate, max.	12 Mbit/s	12 Mbit/s
в—Џ Number of DP slaves, max.	124	124
Services
вЂ” PG/OP communication	Yes	Yes
вЂ” Routing	Yes	Yes
вЂ” Global data communication	No	No
вЂ” S7 basic communication	Yes; I blocks only	Yes; I blocks only
вЂ” S7 communication	Yes	Yes
вЂ” S7 communication, as client	No	No
вЂ” S7 communication, as server	Yes	Yes
вЂ” Equidistance	Yes	Yes
вЂ” Isochronous mode	Yes; OB 61; isochronous mode can only be used alternatively on PROFIBUS DP or PROFINET IO	Yes; OB 61; isochronous mode can only be used alternatively on PROFIBUS DP or PROFINET IO
вЂ” SYNC/FREEZE	Yes	Yes
вЂ” Activation/deactivation of DP slaves	Yes	Yes
вЂ” Number of DP slaves that can be simultaneously activated/deactivated, max.	8	8
вЂ” Direct data exchange (slave-to-slave communication)	Yes; As subscriber	Yes; As subscriber
вЂ” DPV1	Yes	Yes
Address area
вЂ” Inputs, max.	2 kbyte	2 kbyte
вЂ” Outputs, max.	2 kbyte	2 kbyte
User data per DP slave
вЂ” Inputs, max.	244 byte	244 byte
вЂ” Outputs, max.	244 byte	244 byte
DP slave
в—Џ Transmission rate, max.	12 Mbit/s	12 Mbit/s
в—Џ automatic baud rate search	Yes; only with passive interface	Yes; only with passive interface
в—Џ Address area, max.	32	32
в—Џ User data per address area, max.	32 byte	32 byte
Services
вЂ” PG/OP communication	Yes	Yes
вЂ” Routing	Yes; Only with active interface	Yes; Only with active interface
вЂ” Global data communication	No	No
вЂ” S7 basic communication	No	No
вЂ” S7 communication	Yes	Yes
вЂ” S7 communication, as client	No	No
вЂ” S7 communication, as server	Yes; Connection configured on one side only	Yes; Connection configured on one side only
вЂ” Direct data exchange (slave-to-slave communication)	Yes	Yes
вЂ” DPV1	No	No
Transfer memory
вЂ” Inputs	244 byte	244 byte
вЂ” Outputs	244 byte	244 byte
2. Interface
Interface type	PROFINET	PROFINET
Physics	Ethernet RJ45	Ethernet RJ45
Isolated	Yes	Yes
automatic detection of transmission rate	Yes; 10/100 Mbit/s	Yes; 10/100 Mbit/s
Autonegotiation	Yes	Yes
Autocrossing	Yes	Yes
Change of IP address at runtime, supported	Yes	Yes
Interface types
в—Џ Number of ports	2	2
в—Џ integrated switch	Yes	Yes
Media redundancy
в—Џ supported	Yes	Yes
в—Џ Switchover time on line break, typ.	200 ms; PROFINET MRP	200 ms; PROFINET MRP
в—Џ Number of stations in the ring, max.	50	50
Functionality
в—Џ MPI	No	No
в—Џ PROFINET IO Controller	Yes; Also simultaneously with IO-Device functionality	Yes; Also simultaneously with IO-Device functionality
в—Џ PROFINET IO Device	Yes; Also simultaneously with IO Controller functionality	Yes; Also simultaneously with IO Controller functionality
в—Џ PROFINET CBA	Yes	Yes
в—Џ PROFIBUS DP master	No	No
в—Џ PROFIBUS DP slave	No	No
в—Џ Open IE communication	Yes; Via TCP/IP, ISO on TCP, and UDP	Yes; Via TCP/IP, ISO on TCP, and UDP
в—Џ Web server	Yes; only read function	Yes; only read function
PROFINET IO Controller
в—Џ Transmission rate, max.	100 Mbit/s	100 Mbit/s
Services
вЂ” PG/OP communication	Yes	Yes
вЂ” Routing	Yes	Yes
вЂ” S7 communication	Yes; With loadable FBs, max. configurable connections: 14, max. number of instances: 32	Yes; With loadable FBs, max. configurable connections: 14, max. number of instances: 32
вЂ” Isochronous mode	Yes; OB 61; isochronous mode can only be used alternatively on PROFIBUS DP or PROFINET IO	Yes; OB 61; isochronous mode can only be used alternatively on PROFIBUS DP or PROFINET IO
вЂ” Open IE communication	Yes; Via TCP/IP, ISO on TCP, and UDP	Yes; Via TCP/IP, ISO on TCP, and UDP
вЂ” IRT	Yes	Yes
вЂ” Shared device	Yes	Yes
вЂ” Prioritized startup	Yes	Yes
вЂ” Number of IO devices with prioritized startup, max.	32	32
вЂ” Number of connectable IO Devices, max.	128	128
вЂ” Of which IO devices with IRT, max.	64	64
вЂ” of which in line, max.	64	64
вЂ” Number of IO Devices with IRT and the option "high flexibility"	128	128
вЂ” of which in line, max.	61	61
вЂ” Number of connectable IO Devices for RT, max.	128	128
вЂ” of which in line, max.	128	128
вЂ” Activation/deactivation of IO Devices	Yes	Yes
вЂ” Number of IO Devices that can be simultaneously activated/deactivated, max.	8	8
вЂ” IO Devices changing during operation (partner ports), supported	Yes	Yes
вЂ” Number of IO Devices per tool, max.	8	8
вЂ” Device replacement without swap medium	Yes	Yes
вЂ” Send cycles	250 Ојs, 500 Ојs,1 ms; 2 ms, 4 ms (not in the case of IRT with "high flexibility" option)	250 Ојs, 500 Ојs,1 ms; 2 ms, 4 ms (not in the case of IRT with "high flexibility" option)
вЂ” Updating time	250 µs to 512 ms (depending on the operating mode, see Manual "S7-300 CPU 31xC and CPU 31x, Technical Data" for more details)	250 µs to 512 ms (depending on the operating mode, see Manual "S7-300 CPU 31xC and CPU 31x, Technical Data" for more details)
Address area
вЂ” Inputs, max.	2 kbyte	2 kbyte
вЂ” Outputs, max.	2 kbyte	2 kbyte
вЂ” User data consistency, max.	1 024 byte	1 024 byte
PROFINET IO Device
Services
вЂ” PG/OP communication	Yes	Yes
вЂ” Routing	Yes	Yes
вЂ” S7 communication	Yes; With loadable FBs, max. configurable connections: 14, max. number of instances: 32	Yes; With loadable FBs, max. configurable connections: 14, max. number of instances: 32
вЂ” Isochronous mode	No	No
вЂ” Open IE communication	Yes; Via TCP/IP, ISO on TCP, and UDP	Yes; Via TCP/IP, ISO on TCP, and UDP
вЂ” IRT	Yes	Yes
вЂ” PROFIenergy	Yes; With SFB 73 / 74 prepared for loadable PROFIenergy standard FB for I-Device	Yes; With SFB 73 / 74 prepared for loadable PROFIenergy standard FB for I-Device
вЂ” Shared device	Yes	Yes
вЂ” Number of IO Controllers with shared device, max.	2	2
Transfer memory
вЂ” Inputs, max.	1 440 byte; Per IO Controller with shared device	1 440 byte; Per IO Controller with shared device
вЂ” Outputs, max.	1 440 byte; Per IO Controller with shared device	1 440 byte; Per IO Controller with shared device
Submodules
вЂ” Number, max.	64	64
вЂ” User data per submodule, max.	1 024 byte	1 024 byte
PROFINET CBA
в—Џ acyclic transmission	Yes	Yes
в—Џ cyclic transmission	Yes	Yes
Open IE communication
в—Џ Number of connections, max.	8	8
в—Џ Local port numbers used at the system end	0, 20, 21, 25, 80, 102, 135, 161, 8080, 34962, 34963, 34964, 65532, 65533, 65534, 65535	0, 20, 21, 25, 80, 102, 135, 161, 8080, 34962, 34963, 34964, 65532, 65533, 65534, 65535
в—Џ Keep-alive function, supported	Yes	Yes
Protocols
Open IE communication
в—Џ TCP/IP	Yes; via integrated PROFINET interface and loadable FBs	Yes; via integrated PROFINET interface and loadable FBs
вЂ” Data length for connection type 01H, max.	1 460 byte	1 460 byte
вЂ” Data length for connection type 11H, max.	32 768 byte	32 768 byte
вЂ” several passive connections per port, supported	Yes	Yes
в—Џ ISO-on-TCP (RFC1006)	Yes; via integrated PROFINET interface and loadable FBs	Yes; via integrated PROFINET interface and loadable FBs
вЂ” Data length, max.	32 768 byte	32 768 byte
в—Џ UDP	Yes; via integrated PROFINET interface and loadable FBs	Yes; via integrated PROFINET interface and loadable FBs
вЂ” Data length, max.	1 472 byte	1 472 byte
Web server
в—Џ User-defined websites	Yes	Yes
в—Џ Number of HTTP clients	5	5
Isochronous mode
Isochronous operation (application synchronized up to terminal)	Yes; Via PROFIBUS DP or PROFINET interface	Yes; Via PROFIBUS DP or PROFINET interface
Communication functions
PG/OP communication	Yes	Yes
Data record routing	Yes	Yes
Global data communication
в—Џ supported	Yes	Yes
в—Џ Number of GD loops, max.	8	8
в—Џ Number of GD packets, max.	8	8
в—Џ Number of GD packets, transmitter, max.	8	8
в—Џ Number of GD packets, receiver, max.	8	8
в—Џ Size of GD packets, max.	22 byte	22 byte
в—Џ Size of GD packet (of which consistent), max.	22 byte	22 byte
S7 basic communication
в—Џ supported	Yes	Yes
в—Џ User data per job, max.	76 byte	76 byte
в—Џ User data per job (of which consistent), max.	76 byte; 76 bytes (with X_SEND or X_RCV); 64 bytes (with X_PUT or X_GET as server)	76 byte; 76 bytes (with X_SEND or X_RCV); 64 bytes (with X_PUT or X_GET as server)
S7 communication
в—Џ supported	Yes	Yes
в—Џ as server	Yes	Yes
в—Џ as client	Yes; via integrated PROFINET interface and loadable FB or via CP and loadable FB	Yes; via integrated PROFINET interface and loadable FB or via CP and loadable FB
в—Џ User data per job, max.	See online help of STEP 7 (shared parameters of the SFBs/FBs and of the SFCs/FCs of S7 Communication)	See online help of STEP 7 (shared parameters of the SFBs/FBs and of the SFCs/FCs of S7 Communication)
S5 compatible communication
в—Џ supported	Yes; via CP and loadable FC	Yes; via CP and loadable FC
Web server
в—Џ supported	Yes; only read function	Yes; only read function
PROFINET CBA (at set setpoint communication load)
в—Џ Setpoint for the CPU communication load	50 %	50 %
в—Џ Number of remote interconnection partners	32	32
в—Џ Number of functions, master/slave	30	30
в—Џ Total of all master/slave connections	1 000	1 000
в—Џ Data length of all incoming connections master/slave, max.	4 000 byte	4 000 byte
в—Џ Data length of all outgoing connections master/slave, max.	4 000 byte	4 000 byte
в—Џ Number of device-internal and PROFIBUS interconnections	500	500
в—Џ Data length of device-internal und PROFIBUS interconnections, max.	4 000 byte	4 000 byte
в—Џ Data length per connection, max.	1 400 byte	1 400 byte
Remote interconnections with acyclic transmission
вЂ” Sampling frequency: Sampling time, min.	500 ms	500 ms
вЂ” Number of incoming interconnections	100	100
вЂ” Number of outgoing interconnections	100	100
вЂ” Data length of all incoming interconnections, max.	2 000 byte	2 000 byte
вЂ” Data length of all outgoing interconnections, max.	2 000 byte	2 000 byte
вЂ” Data length per connection, max.	1 400 byte	1 400 byte
Remote interconnections with cyclic transmission
вЂ” Transmission frequency: Transmission interval, min.	10 ms	10 ms
вЂ” Number of incoming interconnections	200	200
вЂ” Number of outgoing interconnections	200	200
вЂ” Data length of all incoming interconnections, max.	2 000 byte	2 000 byte
вЂ” Data length of all outgoing interconnections, max.	2 000 byte	2 000 byte
вЂ” Data length per connection, max.	450 byte	450 byte
HMI variables via PROFINET (acyclic)
вЂ” Number of stations that can log on for HMI variables (PN OPC/iMap)	3; 2x PN OPC/1x iMap	3; 2x PN OPC/1x iMap
вЂ” HMI variable updating	500 ms	500 ms
вЂ” Number of HMI variables	200	200
вЂ” Data length of all HMI variables, max.	2 000 byte	2 000 byte
PROFIBUS proxy functionality
вЂ” supported	Yes	Yes
вЂ” Number of linked PROFIBUS devices	16	16
вЂ” Data length per connection, max.	240 byte; Slave-dependent	240 byte; Slave-dependent
Number of connections
в—Џ overall	16	16
в—Џ usable for PG communication	15	15
вЂ” reserved for PG communication	1	1
вЂ” adjustable for PG communication, min.	1	1
вЂ” adjustable for PG communication, max.	15	15
в—Џ usable for OP communication	15	15
вЂ” reserved for OP communication	1	1
вЂ” adjustable for OP communication, min.	1	1
вЂ” adjustable for OP communication, max.	15	15
в—Џ usable for S7 basic communication	14	14
вЂ” reserved for S7 basic communication	0	0
вЂ” adjustable for S7 basic communication, min.	0	0
вЂ” adjustable for S7 basic communication, max.	14	14
в—Џ usable for S7 communication	14	14
вЂ” reserved for S7 communication	0	0
вЂ” adjustable for S7 communication, min.	0	0
вЂ” adjustable for S7 communication, max.	14	14
в—Џ total number of instances, max.	32	32
в—Џ usable for routing	X1 as MPI: max. 10; X1 as DP master: max. 24; X1 as DP slave (active): max. 14; X2 as PROFINET: 24 max.	X1 as MPI: max. 10; X1 as DP master: max. 24; X1 as DP slave (active): max. 14; X2 as PROFINET: 24 max.
S7 message functions
Number of login stations for message functions, max.	16; Depending on the configured connections for PG/OP and S7 basic communication	16; Depending on the configured connections for PG/OP and S7 basic communication
Process diagnostic messages	Yes	Yes
simultaneously active Alarm-S blocks, max.	300	300
Test commissioning functions
Status block	Yes; Up to 2 simultaneously	Yes; Up to 2 simultaneously
Single step	Yes	Yes
Number of breakpoints	4	4
Status/control
в—Џ Status/control variable	Yes	Yes
в—Џ Variables	Inputs, outputs, memory bits, DB, times, counters	Inputs, outputs, memory bits, DB, times, counters
в—Џ Number of variables, max.	30	30
вЂ” of which status variables, max.	30	30
вЂ” of which control variables, max.	14	14
Forcing
в—Џ Forcing	Yes	Yes
в—Џ Forcing, variables	Inputs, outputs	Inputs, outputs
в—Џ Number of variables, max.	10	10
Diagnostic buffer
в—Џ present	Yes	Yes
в—Џ Number of entries, max.	500	500
вЂ” adjustable	No	No
вЂ” of which powerfail-proof	100	100
в—Џ Number of entries readable in RUN, max.	499	499
вЂ” can be set	Yes	Yes
вЂ” preset	10	10
Service data
в—Џ can be read out	Yes	Yes
Isolation
Isolation tested with		500V AC for 1 minute
Standards, approvals, certificates
CE mark	Yes	Yes
UL approval	Yes; File E239877	Yes; File E239877
FM approval	Yes; CofC 3028431	Yes; CofC 3028431
RCM (formerly C-TICK)	Yes	Yes
KC approval	Yes	Yes
EAC (formerly Gost-R)	Yes	Yes
Railway application
в—Џ EN 50155		Yes; Sections 4, 5 and 12; no further agreements apply; T1, Category 1, Class A/B
Marine approval
в—Џ American Bureau of Shipping (ABS)	Yes
Use in hazardous areas
в—Џ ATEX	Yes	Yes
Ambient conditions
Ambient temperature during operation
в—Џ min.	-25 °C; = Tmin	-25 °C; = Tmin
в—Џ max.	60 °C; = Tmax	60 °C; = Tmax; the rated temperature range of -25 ... +55 °C (T1) applies for the use on railway vehicles according to EN50155
Ambient temperature during storage/transportation
в—Џ min.	-40 °C	-40 °C
в—Џ max.	70 °C	70 °C
Altitude during operation relating to sea level
в—Џ Ambient air temperature-barometric pressure-altitude	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
в—Џ With condensation, tested in accordance with IEC 60068-2-38, max.	100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation	100 %; RH incl. condensation / frost (no commissioning in bedewed state), horizontal installation
Resistance
Use in stationary industrial systems
вЂ” to biologically active substances according to EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna); Class 3B3 on request	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation in corrosive atmospheres!
вЂ” to chemically active substances according to EN 60721-3-3	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
вЂ” to mechanically active substances according to EN 60721-3-3	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Configuration
Configuration software
в—Џ STEP 7	Yes; V5.5 or higher	Yes; V5.5 or higher
Programming
в—Џ Command set	see instruction list	see instruction list
в—Џ Nesting levels	8	8
в—Џ System functions (SFC)	see instruction list	see instruction list
в—Џ System function blocks (SFB)	see instruction list	see instruction list
Programming language
вЂ” LAD	Yes	Yes
вЂ” FBD	Yes	Yes
вЂ” STL	Yes	Yes
вЂ” SCL	Yes	Yes
вЂ” CFC	Yes	Yes
вЂ” GRAPH	Yes	Yes
вЂ” HiGraph®	Yes	Yes
Know-how protection
в—Џ User program protection/password protection	Yes	Yes
в—Џ Block encryption	Yes; With S7 block Privacy	Yes; With S7 block Privacy
Dimensions
Width	40 mm	40 mm
Height	125 mm	125 mm
Depth	130 mm	130 mm
Weights
Weight, approx.	340 g	340 g

skener.ru

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
Бесконтактные выключатели Конечные выключатели Оптические датчики Энкодеры

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FS - Установка умягчения

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FK - Установка обезжелезивания