Milltronics MUS . Технические данные. Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на Milltronics MUS

| | | | | | | |

Technical specifications
Mode of operation
Measuring principle	Heavy duty strain gauge load cells measuring load on belt conveyor idlers
Typical applications	Monitor fractionated stone on secondary surge belts and recirculating loads Track daily production totals
Measurement accuracy
Accuracy¹⁾	± 0.5 вЂ¦ 1 % of totalization over 25 вЂ¦ 100 % operating range, application dependent
Repeatability	± 0.1 %
Medium conditions
Max. material temperature	65 °C (150 °F)
Belt design
Belt width	Standard duty up to 1 000 mm (CEMA width up to 42 inch) Heavy-duty up to 1 524 mm (CEMA width up to 60 inch) Refer to outline dimension section
Belt speed	Up to 3.0 m/s (600 fpm)²⁾
Capacity	Up to 5 000 t/h at maximum belt speed
Conveyor incline	± 20° from horizontal, fixed incline Up to ± 30° with reduced accuracy³⁾
Idlers
Idler profile	Flat to 35° To 45° with reduced accuracy³⁾
Idler diameter	50 вЂ¦ 180 mm (2 вЂ¦ 7 inch)
Idler spacing	0.6 вЂ¦ 1.5 m (2.0 вЂ¦ 5.0 ft)
Load cell
Construction	Nickel plated alloy steel Strain gauge protection: silicon
Degree of protection	IP66
Cable length	3 m (10 ft)
Excitation	10 V DC nominal, 15 V DC max.
Output	2 mV/V excitation at rated load cell capacity
Non-linearity and hysteresis	0.02 % of rated output
Non-repeatability	0.01 % of rated output
Capacity
Standard duty ranges	20, 30, 50, 75, 100 kg (44, 66, 110, 165, 220 lb)
Heavy-duty ranges	50, 100, 150, 200, 500 kg (110, 220, 330, 440, 1 100 lb)
Overload	150 % of rated capacity, ultimate 200 % of rated capacity
Temperature	-40 вЂ¦ +65 °C (-40 вЂ¦ +150 °F) operating range -10 вЂ¦ +40 °C (15 вЂ¦ 105 °F) compensated
Weight	Standard duty up to 44 lb (20 kg), 22 lb (10 kg) per side Heavy-duty up to 64 lb (30 kg), 32 lb (15 kg) per side
Interconnection wiring (to integrator)	< 150 m (500 ft) 18 AWG (0.75 mmІ) 6 conductor shielded cable > 150 m вЂ¦ 300 m (500 вЂ¦ 1 000 ft) 18 вЂ¦ 22 AWG (0.75 вЂ¦ 0.34 mmІ) 8 conductor shielded cable
Hazardous locations	Consult the factory
Approvals	CE, RCM, EAC, CMC, KCC

¹⁾ Accuracy subject to: on factory approved installations the belt scale systemвЂ™s totalized weight will be within the specified accuracy when compared to a known weighed material test sample. The test rate must be within the specified range of the design capacity and held constant for the duration of the test. The minimum material test sample must be equivalent to a sample obtained at the test flow rate for three revolutions of the belt or at least ten minutes running time, whichever is greater.

²⁾ Contact Siemens application engineering (factorysupport.smpi@siemens.com) for consideration of higher belt speeds.

³⁾ Review by Siemens application engineer required.