Ordering and technology . Технические данные. Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на Ordering and technology

| | | | |

General technical data

Coolant temperature and installation altitude

Current derating

The permissible coolant temperatures and installation altitudes for SINAMICS DC MASTER Cabinet as well as the associated maximum permissible load in continuous operation can be taken from the following table (the load is specified as a % of the rated DC current).

Note:

The rated DC current of the drive cabinets corresponds to the rated DC current of the DC converters installed in them. The degree of protection and cooling type of the drive cabinets as well as the coolant temperature and installation altitude influence the max. permissible load in continuous operation. In practice, the rated current of the DC motor lies significantly below the rated DC current of the next largest converter in order to be able to fully utilize the high overload capability of the motor. The derating factors below should be taken into account for the particular application.

Example:
Rated current of the DC motor 450 A, coolant temperature 40 °C, installation altitude of the drive cabinet 2 000 m, selected rated DC current of the converter 600 A, derating factor 81 %.

Result:
The maximum permissible load of the drive cabinet in continuous operation is 486 A, and is therefore sufficient for the motor.

		Maximum permissible load of the drive cabinets in continuous operation (load specified as a % of the rated DC current)
		Installation altitude above sea level (The derating factors for intermediate values can be obtained through interpolation.)
Ambient or coolant temperature	Units	1 000 m					2 000 m					3 000 m					4 000 m					5 000 m
	from 1500 A в‡’					в‡“	в‡’				в‡“	в‡’				в‡“	в‡’				в‡“	в‡’				в‡“
	from 950 A в‡’				в‡“		в‡’			в‡“		в‡’			в‡“		в‡’			в‡“		в‡’			в‡“
	from 720 A в‡’			в‡“			в‡’		в‡“			в‡’		в‡“			в‡’		в‡“			в‡’		в‡“
	from 210 A в‡’		в‡“				в‡’	в‡“				в‡’	в‡“				в‡’	в‡“				в‡’	в‡“
	up to 125 A в‡’	в‡“	в‡“				в‡’ в‡“	в‡“				в‡’ в‡“	в‡“				в‡’ в‡“	в‡“				в‡’ в‡“	в‡“
Degree of protection IP20 up to IP21
25 °C		100%	100%	100%	100%	100%	100%	96%	93%	97%	93%	96%	86%	83%	87%	83%	86%	76%	73%	77%	73%	78%	68%	65%	69%	65%
30 °C		100%	100%	100%	100%	100%	100%	91%	88%	92%	88%	90%	81%	78%	82%	78%	80%	71%	68%	72%	68%
35 °C		100%	100%	95%	99%	95%	94%	86%	83%	87%	83%	84%	76%	73%	77%	73%
40 °C		100%	95%	90%	94%	90%	88%	81%	78%	82%	78%
45 °C		94%	90%	85%	89%	85%	82%	76%	73%	77%	73%
50 °C		88%
Degree of protection IP23, IP43, IP54
25 °C		100%	100%	100%	100%	100%	100%	98%	96%	98%	98%	96%	88%	86%	88%	88%	86%	78%	76%	78%	78%	78%	70%	68%	70%	70%
30 °C		100%	100%	100%	100%	100%	100%	93%	91%	93%	93%	90%	83%	81%	83%	83%	80%	73%	71%	73%	73%
35 °C		100%	100%	98%	100%	100%	94%	88%	86%	88%	88%	84%	78%	76%	78%	78%
40 °C		100%	95%	93%	95%	95%	88%	83%	81%	83%	83%
45 °C		94%	90%	88%	90%	90%	82%	78%	76%	78%	78%
50 °C		88%

Voltage derating

The cabinets can be operated up to an installation altitude of 4 000 m above sea level with the specified rated supply voltages. The line supply voltages may have overvoltage category III with respect to ground. For installation altitudes above 4 000 m, in some cases, it will be necessary to reduce the supply voltage or ensure that overvoltage category II is maintained. Detailed information is provided in the Operating Instructions.

Installation location

In their basic version (IP20), SINAMICS DC MASTER Cabinet drive cabinets are intended for use in closed electrical rooms (according to EN 61800-5-1).

These rooms must be dry and dust free, in order to prevent deposits of dirt accumulating, which in conjunction with moisture, could result in a conductive connection between live parts.

In plants, frequently electrical operating rooms have central power and fresh air supplies, which fulfill these requirements. If this is not the case, then the drive cabinet must be ordered with a higher degree of protection by specifying the appropriate options (M21, M23, M43, M54 and M58).

Relevant standards
EN 50274	Low-voltage switchgear and controlgear assemblies: Protection against electric shock – protection against accidental, direct contact with dangerous live parts, option M60 provides additional touch protection in accordance with BGV A3
EN 60529	Degrees of protection provided by the enclosures (IP code)
EN 61800-3	Adjustable speed electrical power drive systems, Part 3 – EMC product standard including specific test methods
EN 61800вЂ‘5вЂ‘1	Adjustable speed electrical power drive systems – Part 5вЂ‘1: Requirements regarding safety – electrical, thermal, and energy requirements
EN 62477вЂ‘1 (product standard, combines safety-relevant standards such as IEC 61800вЂ‘5вЂ‘1, IEC 60204вЂ‘1)	Safety requirements for power semiconductor converter systems – Part 1: General information
EN 60204вЂ‘1 (VDE 0113вЂ‘1) where applicable	Safety of machinery – Electrical equipment of machines – Part 1: General requirements
The following standards are applicable for the SINAMICS DC MASTER DC Converter chassis units	EN 60146вЂ‘1вЂ‘1; EN 61800вЂ‘5вЂ‘1; IEC 62103 (identical with EN 50178). Additional information is provided in Catalog D 23.1.
Electrical data
Overvoltage category	Category ll according to EN 61800вЂ‘5вЂ‘1 within line supply circuits Category lll according to EN 61800вЂ‘5вЂ‘1 for line supply circuits with respect to the surroundings (other line supply circuits, enclosure, electronics)
Overvoltage strength	Class 1 acc. to EN 50178
Radio interference suppression	SINAMICS DC MASTER Cabinet are operated in industrial environments and fulfill the requirements of EN 61800вЂ‘3, Categories C3 and C4. Radio interference suppression filters are required for use in Category C2 (option L00)
Auxiliary power supply	400 V 3 AC at 50 Hz, optional: 60 Hz and/or other voltages
Overload capability	x Г— I_n 1.8
Mechanical data
Degree of protection	IP20 according to EN 60529; optional: IP21, IP23, IP43 and IP54
Protection class	Class 1 acc. to EN 61140
Cooling type	Increased air cooling with integrated fan 0 up to 55 °C; the derating depends on the ambient temperature and installation altitude; see the table on the current derating
Closed-loop control constancy
for pulse encoder operation and digital setpoint	О”_n = 0.006 % of the rated motor speed
for analog tachometer and analog setpoint¹⁾	О”_n = 0.1 % of the rated motor speed
Environmental compatibility	Materials free of hazardous substances have been used for all of the essential parts. Only very few materials containing halogens are used for cable insulation and cable ducts (alternative designs available on request). All of the materials correspond to the RoHS criteria, with the exception of the backup battery in the AOP30. Environmental compatibility is also a key criterion in selecting supplier parts.
Environmental conditions
Permissible ambient temperature during storage and transport	–25 ... +70 °C
Permissible humidity	Relative air humidity в‰¤ 95 % (75 % at 17 °C as annual average, 95 % at 24 °C max., condensation is not permissible)
Climate class	3K3 according to EN 60721вЂ‘3вЂ‘3
Insulation	Pollution degree 2 according to EN 61800вЂ‘5вЂ‘1 Condensation not permissible
Installation altitude	в‰¤ 1 000 m above sea level (100 % load capability) > 1 000 ... 5 000 m above sea level (see under "Coolant temperature and installation altitude")
Mechanical stability	Storage	Transport	Operation
Vibratory load	1M2 according to EN 60721вЂ‘3вЂ‘1 (toppling not permissible)	1.5 mm at 2 ... 9 Hz, 5 m/s² at 9 ... 200 Hz acc. to EN 60721вЂ‘3вЂ‘2 (toppling not permissible)	3M2 according to EN 60721-3-3
Shock load	1M2 according to EN 60721вЂ‘3вЂ‘1 (toppling not permissible)	40 m/s² at 11 ms acc. to acc. to EN 60721вЂ‘3вЂ‘2 (toppling not permissible)	3M2 according to EN 60721-3-3
Approvals
Version according to UL	A converter cabinet design according to UL can be ordered by specifying option U09. Certification must be separately carried out.
Marine version	With option M66, the cabinet is provided in a marine design for onboard applications. Certification by the appropriate authorities must be carried out separately.

¹⁾ Conditions:
The closed-loop control (PI control) constancy is referred to the rated motor speed and applies when the SINAMICS DC MASTER is in the warm operating condition. This is based on the following preconditions:

Temperature changes of ± 10 °C
Line supply voltage changes of +10 %/–5 % of the rated input voltage
Temperature coefficient of tachometer generator with temperature compensation: 0.15 every 10 °C (for analog tachometer generator only)
Constant setpoint

Notes on dimensioning the fault current and insulation monitoring:

The basic version does not include any fault current monitoring devices. However, these can be ordered as option (L82 for grounded line supplies). Insulation monitoring according to the applicable regulations must be provided for operation in non-grounded IT line supplies. Options L87 or L88 are available to realize this.

Notes on touch protection:

In the standard version of the SINAMICS DC MASTER Cabinet, in compliance with the current standards, finger and back of hand protection is ensured when the cabinet doors are open. With option M60 "Additional touch protection", the drive cabinets are equipped with additional touch protection corresponding to BGV A3.

Notes on the armature circuit busbars:

Aluminum armature busbars are used for cabinets with rated DC currents of 1 500, 1 600, 1 900, 2 000 and 2 200 A. When selecting option M11, nickel-plated copper busbars are supplied.

SINAMICS DC MASTER Cabinet for 400 V 3 AC, 60 to 210 A, two-quadrant operation

		Type
		6RM8025- 6DS22вЂ‘0AA0	6RM8028- 6DS22вЂ‘0AA0	6RM8031- 6DS22вЂ‘0AA0	6RM8075- 6DS22вЂ‘0AA0
Rated armature supply voltage	V	3 AC 400 (+15 %/–20 %)
Rated armature input current	A	49.8	74.7	103.75	174.3
Cooling air requirement	mі/h	800	800	800	800
Sound pressure level	dB (A)	72	72	72	72
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	485	485	485	485
Rated DC current	A	60	90	125	210
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	29.1	43.65	60.625	101.85
Power loss at rated DC current	W	463	592	691	1 152
Rated DC field voltage	V	max. 325	max. 325	max. 325	max. 325
Rated DC field current	A	10	10	10	15
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	1 Г— 16	1 Г— 25	1 Г— 50	1 Г— 95
Armature circuit connection	Number Г— mm²	1 Г— 16	1 Г— 25	1 Г— 50	1 Г— 95
Field circuit connection	Number Г— mm²	1 Г— 1.5	1 Г— 1.5	1 Г— 1.5	1 Г— 2.5
Auxiliary power supply	mm²	2.5	2.5	2.5	4
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	63	80	125	200
Max. permissible short-circuit current	kA	50²⁾	50²⁾	50²⁾	50³⁾
Auxiliary power supply	A	16	16	16	25
Max. permissible short-circuit current	kA	30	30	30	30
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	600	600	600	600
Height	mm	2 326	2 326	2 326	2 326
Depth	mm	600	600	600	600
Size		BC	BC	BC	BC
Weight, approx.	kg	233	233	240	263

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 43 kA.

³⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 25 kA.

SINAMICS DC MASTER Cabinet for 400 V 3 AC, 280 to 850 A, two-quadrant operation

		Type
		6RM8078- 6DS22вЂ‘0AA0	6RM8081- 6DS22вЂ‘0AA0	6RM8085- 6DS22вЂ‘0AA0	6RM8087- 6DS22вЂ‘0AA0
Rated armature supply voltage	V	3 AC 400 (+15 %/–20 %)
Rated armature input current	A	232.4	332	498	705.5
Cooling air requirement	mі/h	800	600	600	600
Sound pressure level	dB (A)	72	74	74	74
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	485	485	485	485
Rated DC current	A	280	400	600	850
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	135.8	194	291	412.25
Power loss at rated DC current	W	1 482	2 131	2 884	3 759
Rated DC field voltage	V	max. 325	max. 325	max. 325	max. 325
Rated DC field current	A	15	25	25	30
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	1 Г— 120	1 Г— 185	2 Г— 150	2 Г— 240
Armature circuit connection	Number Г— mm²	2 Г— 50	1 Г— 185	2 Г— 150	4 Г— 95
Field circuit connection	Number Г— mm²	1 Г— 2.5	1 Г— 4	1 Г— 4	1 Г— 4
Auxiliary power supply	mm²	4	10	10	16
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	250	355	500	710
Max. permissible short-circuit current	kA	50²⁾	50	50	50
Auxiliary power supply	A	25	50	50	63
Max. permissible short-circuit current	kA	30	30	30	30
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	600	800	800	1 200
Height	mm	2 326	2 200	2 200	2 200
Depth	mm	600	600	600	600
Size		BC	CC	CC	DC
Weight, approx.	kg	273	320	340	490

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 25 kA.

SINAMICS DC MASTER Cabinet for 400 V 3 AC, 1 200 to 3 000 A, two-quadrant operation

		Type
		6RM8091- 6DS22вЂ‘0AA0	6RM8093- 4DS22вЂ‘0AA0	6RM8095- 4DS22вЂ‘0AA0	6RM8098- 4DS22вЂ‘0AA0
Rated armature supply voltage	V	3 AC 400 (+15 %/–20 %)
Rated armature input current	A	996	1 328	1 660	2 490
Cooling air requirement	mі/h	1 000	3 000	3 000	3 000
Sound pressure level	dB (A)	76	78	78	78
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	485	485	485	485
Rated DC current	A	1 200	1 600	2 000	3 000
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	582	776	970	1 455
Power loss at rated DC current	W	4 697	6 430	7 618	11 747
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	30	40	40	40
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	4 Г— 150	6 Г— 150	6 Г— 185	8 Г— 240
Armature circuit connection	Number Г— mm²	4 Г— 185	8 Г— 95	8 Г— 150	8 Г— 240
Field circuit connection	Number Г— mm²	1 Г— 4	1 Г— 6	1 Г— 6	1 Г— 6
Auxiliary power supply	mm²	16	35	35	35
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	–²⁾	–²⁾	–²⁾	–²⁾
Max. permissible short-circuit current	kA	65	75	75	75
Auxiliary power supply	A	63	100	100	100
Max. permissible short-circuit current	kA	30	50	50	50
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	1 200	1 400	1 400	1 400
Height	mm	2 200	2 200	2 200	2 200
Depth	mm	600	600	600	600
Size		DC	EC	EC	EC
Weight, approx.	kg	570	760	800	930

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

SINAMICS DC MASTER Cabinet for 480 V 3 AC, 60 to 280 A, two-quadrant operation

		Type
		6RM8025- 6FS22вЂ‘0AA0	6RM8028- 6FS22вЂ‘0AA0	6RM8031- 6FS22вЂ‘0AA0	6RM8075- 6FS22вЂ‘0AA0	6RM8078- 6FS22вЂ‘0AA0
Rated armature supply voltage	V	3 AC 480 (+10 %/–20 %)
Rated armature input current	A	49.8	74.7	103.75	174.3	232.4
Cooling air requirement	mі/h	800	800	800	800	800
Sound pressure level	dB (A)	72	72	72	72	72
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	575	575	575	575	575
Rated DC current	A	60	90	125	210	280
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8	1.8
Rated power	kW	34.5	51.75	71.875	120.75	161
Power loss at rated DC current	W	512	614	713	1 225	1 481
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	10	10	10	15	15
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	1 Г— 16	1 Г— 25	1 Г— 50	1 Г— 95	1 Г— 120
Armature circuit connection	Number Г— mm²	1 Г— 16	1 Г— 25	1 Г— 50	1 Г— 95	2 Г— 50
Field circuit connection	Number Г— mm²	1 Г— 1.5	1 Г— 1.5	1 Г— 1.5	1 Г— 2.5	1 Г— 2.5
Auxiliary power supply	mm²	2.5	2.5	2.5	4	4
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	63	80	125	200	250
Max. permissible short-circuit current	kA	50²⁾	50²⁾	50²⁾	50³⁾	50³⁾
Auxiliary power supply	A	16	16	16	25	25
Max. permissible short-circuit current	kA	30	30	30	30	30
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	600	600	600	600	600
Height	mm	2 326	2 326	2 326	2 326	2 326
Depth	mm	600	600	600	600	600
Size		BC	BC	BC	BC	BC
Weight, approx.	kg	233	238	240	273	273

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 43 kA.

³⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 25 kA.

SINAMICS DC MASTER Cabinet for 480 V 3 AC, 450 to 1 200 A, two-quadrant operation

		Type
		6RM8082- 6FS22вЂ‘0AA0	6RM8085- 6FS22вЂ‘0AA0	6RM8087- 6FS22вЂ‘0AA0	6RM8091- 6FS22вЂ‘0AA0
Rated armature supply voltage	V	3 AC 480 (+10 %/–20 %)
Rated armature input current	A	373.5	498	705.5	996
Cooling air requirement	mі/h	600	600	600	1 000
Sound pressure level	dB (A)	74	74	74	76
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	575	575	575	575
Rated DC current	A	450	600	850	1 200
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	258.75	345	488.75	690
Power loss at rated DC current	W	2 377	3 097	3 983	4 857
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	25	25	30	30
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	2 Г— 120	2 Г— 150	2 Г— 240	4 Г— 150
Armature circuit connection	Number Г— mm²	2 Г— 95	2 Г— 150	4 Г— 95	4 Г— 185
Field circuit connection	Number Г— mm²	1 Г— 4	1 Г— 4	1 Г— 4	1 Г— 4
Auxiliary power supply	mm²	10	10	16	16
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	400	500	710	–²⁾
Max. permissible short-circuit current	kA	50	50	50	65
Auxiliary power supply	A	50	50	63	63
Max. permissible short-circuit current	kA	30	30	30	30
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	800	800	1 200	1 200
Height	mm	2 200	2 200	2 200	2 200
Depth	mm	600	600	600	600
Size		CC	CC	DC	DC
Weight, approx.	kg	340	355	500	570

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

SINAMICS DC MASTER Cabinet for 575 V 3 AC, 60 to 400 A, two-quadrant operation

		Type
		6RM8025- 6GS22вЂ‘0AA0	6RM8031- 6GS22вЂ‘0AA0	6RM8075- 6GS22вЂ‘0AA0	6RM8081- 6GS22вЂ‘0AA0
Rated armature supply voltage	V	3 AC 575 (+10 %/–20 %)
Rated armature input current	A	49.8	103.75	174.3	332
Cooling air requirement	mі/h	800	800	800	600
Sound pressure level	dB (A)	72	72	72	74
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	690	690	690	690
Rated DC current	A	60	125	210	400
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	41.4	86.25	144.9	276
Power loss at rated DC current	W	487	762	1 284	2 439
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	10	10	15	25
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	1 Г— 16	1 Г— 50	1 Г— 95	1 Г— 185
Armature circuit connection	Number Г— mm²	1 Г— 16	1 Г— 50	1 Г— 95	1 Г— 185
Field circuit connection	Number Г— mm²	1 Г— 1.5	1 Г— 1.5	1 Г— 2.5	1 Г— 4
Auxiliary power supply	mm²	2.5	2.5	4	10
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	63	125	200	355
Max. permissible short-circuit current	kA	50²⁾	50²⁾	50³⁾	50
Auxiliary power supply	A	16	16	25	50
Max. permissible short-circuit current	kA	30	30	30	30
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	600	600	600	800
Height	mm	2 326	2 326	2 326	2 200
Depth	mm	600	600	600	600
Size		BC	BC	BC	CC
Weight, approx.	kg	233	240	273	335

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 43 kA.

³⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 25 kA.

SINAMICS DC MASTER Cabinet for 575 V 3 AC, 600 to 1 600 A, two-quadrant operation

		Type
		6RM8085- 6GS22вЂ‘0AA0	6RM8087- 6GS22вЂ‘0AA0	6RM8090- 6GS22вЂ‘0AA0	6RM8093- 4GS22вЂ‘0AA0
Rated armature supply voltage	V	3 AC 575 (+10 %/–20 %)
Rated armature input current	A	498	664	913	1 328
Cooling air requirement	mі/h	600	600	1 000	3 000
Sound pressure level	dB (A)	74	74	76	78
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	690	690	690	690
Rated DC current	A	600	800	1 100	1 600
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	414	552	759	1 104
Power loss at rated DC current	W	3 190	3 932	4 583	6 988
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	25	30	30	40
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	2 Г— 150	2 Г— 240	4 Г— 150	6 Г— 150
Armature circuit connection	Number Г— mm²	2 Г— 150	4 Г— 95	4 Г— 120	8 Г— 95
Field circuit connection	Number Г— mm²	1 Г— 4	1 Г— 4	1 Г— 4	1 Г— 6
Auxiliary power supply	mm²	10	16	16	35
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	500	710	–²⁾	–²⁾
Max. permissible short-circuit current	kA	50	50	65	75
Auxiliary power supply	A	50	63	63	100
Max. permissible short-circuit current	kA	30	30	30	50
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	800	1 200	1 200	1 400
Height	mm	2 200	2 200	2 200	2 200
Depth	mm	600	600	600	600
Size		CC	DC	DC	EC
Weight, approx.	kg	355	515	600	775

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

SINAMICS DC MASTER Cabinet for 575 V 3 AC, 2 000 to 2 800 A, two-quadrant operation

		Type
		6RM8095- 4GS22вЂ‘0AA0	6RM8096- 4GS22вЂ‘0AA0	6RM8097- 4GS22вЂ‘0AA0
Rated armature supply voltage	V	3 AC 575 (+10 %/–20 %)
Rated armature input current	A	1 660	1 826	2 324
Cooling air requirement	mі/h	3 000	3 000	3 000
Sound pressure level	dB (A)	78	78	78
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	690	690	690
Rated DC current	A	2 000	2 200	2 800
Overload capability	x Г— I_n	1.8	1.8	1.8
Rated power	kW	1 380	1 518	1 932
Power loss at rated DC current	W	8 090	8 408	11 937
Rated DC field voltage	V	max. 390	max. 390	max. 390
Rated DC field current	A	40	40	40
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	6 Г— 185	8 Г— 150	8 Г— 240
Armature circuit connection	Number Г— mm²	8 Г— 150	8 Г— 185	8 Г— 240
Field circuit connection	Number Г— mm²	1 Г— 6	1 Г— 6	1 Г— 6
Auxiliary power supply	mm²	35	35	35
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	–²⁾	–²⁾	–²⁾
Max. permissible short-circuit current	kA	75	75	75
Auxiliary power supply	A	100	100	100
Max. permissible short-circuit current	kA	50	50	50
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	1 400	1 400	1 400
Height	mm	2 200	2 200	2 200
Depth	mm	600	600	600
Size		EC	EC	EC
Weight, approx.	kg	830	930	1 010

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

SINAMICS DC MASTER Cabinet for 690 V 3 AC, 720 to 2 600 A, two-quadrant operation

		Type
		6RM8086- 6KS22вЂ‘0AA0	6RM8090- 6KS22вЂ‘0AA0	6RM8093- 4KS22вЂ‘0AA0	6RM8095- 4KS22вЂ‘0AA0	6RM8097- 4KS22вЂ‘0AA0
Rated armature supply voltage	V	3 AC 690 (+10 %/–20 %)
Rated armature input current	A	597.6	830	1 245	1 660	2 158
Cooling air requirement	mі/h	600	1 000	3 000	3 000	3 000
Sound pressure level	dB (A)	74	76	78	78	78
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	830	830	830	830	830
Rated DC current	A	720	1 000	1 500	2 000	2 600
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8	1.8
Rated power	kW	597.6	830	1 245	1 660	2 158
Power loss at rated DC current	W	4 012	4 642	7 627	9 175	12 007
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	30	30	40	40	40
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	2 Г— 240	4 Г— 120	6 Г— 120	6 Г— 185	8 Г— 240
Armature circuit connection	Number Г— mm²	4 Г— 95	4 Г— 120	8 Г— 95	8 Г— 150	8 Г— 240
Field circuit connection	Number Г— mm²	1 Г— 4	1 Г— 4	1 Г— 6	1 Г— 6	1 Г— 6
Auxiliary power supply	mm²	16	16	35	35	35
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	630	–²⁾	–²⁾	–²⁾	–²⁾
Max. permissible short-circuit current	kA	50	65	75	75	75
Auxiliary power supply	A	63	63	100	100	100
Max. permissible short-circuit current	kA	30	30	50	50	50
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	1 200	1 200	1 400	1 400	1 600
Height	mm	2 200	2 200	2 200	2 200	2 200
Depth	mm	600	600	600	600	600
Size		DC	DC	EC	EC	FC
Weight, approx.	kg	515	600	795	830	1 050

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

SINAMICS DC MASTER Cabinet for 830 V 3 AC, 950 to 1 900 A and 950 V 3 AC, 2 200 A, two-quadrant operation

		Type
		6RM8088- 6LS22вЂ‘0AA0	6RM8093- 4LS22вЂ‘0AA0	6RM8095- 4LS22вЂ‘0AA0	6RM8096- 4MS22вЂ‘0AA0
Rated armature supply voltage	V	3 AC 830 (+10 %/–20 %)			3 AC 950 (+15 %/–20 %)
Rated armature input current	A	788.5	1 245	1 577	1 826
Cooling air requirement	mі/h	1 000	3 000	3 000	3 000
Sound pressure level	dB (A)	76	78	78	78
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	1 000	1 000	1 000	1 140
Rated DC current	A	950	1 500	1 900	2 200
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	950	1 500	1 900	2 508
Power loss at rated DC current	W	4 911	8 039	9 986	12 957
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	30	40	40	40
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	4 Г— 120	6 Г— 120	6 Г— 185	8 Г— 150
Armature circuit connection	Number Г— mm²	4 Г— 120	8 Г— 95	8 Г— 150	8 Г— 185
Field circuit connection	Number Г— mm²	1 Г— 4	1 Г— 6	1 Г— 6	1 Г— 6
Auxiliary power supply	mm²	16	35	35	35
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	–²⁾	–²⁾	–²⁾	–²⁾
Max. permissible short-circuit current	kA	50	50	50	50
Auxiliary power supply	A	63	100	100	100
Max. permissible short-circuit current	kA	30	50	50	50
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	1 200	1 400	1 400	1 600
Height	mm	2 200	2 200	2 200	2 200
Depth	mm	600	600	600	600
Size		DC	EC	EC	FC
Weight, approx.	kg	600	825	905	1 050

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

SINAMICS DC MASTER Cabinet for 400 V 3 AC, 15 to 90 A, four-quadrant operation

		Type
		6RM8013- 6DV62вЂ‘0AA0	6RM8018- 6DV62вЂ‘0AA0	6RM8025- 6DV62вЂ‘0AA0	6RM8028- 6DV62вЂ‘0AA0
Rated armature supply voltage	V	3 AC 400 (+15 %/–20 %)
Rated armature input current	A	12	25	50	75
Cooling air requirement	mі/h	800	800	800	800
Sound pressure level	dB (A)	72	72	72	72
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	420	420	420	420
Rated DC current	A	15	30	60	90
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	6.3	12.6	25.2	37.8
Power loss at rated DC current	W	292	372	485	587
Rated DC field voltage	V	max. 325	max. 325	max. 325	max. 325
Rated DC field current	A	3	5	10	10
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	1 Г— 2.5	1 Г— 6	1 Г— 16	1 Г— 25
Armature circuit connection	Number Г— mm²	1 Г— 2.5	1 Г— 6	1 Г— 16	1 Г— 25
Field circuit connection	Number Г— mm²	1 Г— 1.5	1 Г— 1.5	1 Г— 1.5	1 Г— 1.5
Auxiliary power supply	mm²	2.5	2.5	2.5	2.5
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	20	32	63	80
Max. permissible short-circuit current	kA	50²⁾	50²⁾	50²⁾	50²⁾
Auxiliary power supply	A	16	16	16	16
Max. permissible short-circuit current	kA	30	30	30	30
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	600	600	600	600
Height	mm	2 326	2 326	2 326	2 326
Depth	mm	600	600	600	600
Size		BC	BC	BC	BC
Weight, approx.	kg	233	213	233	233

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 43 kA.

SINAMICS DC MASTER Cabinet for 400 V 3 AC, 125 to 400 A, four-quadrant operation

		Type
		6RM8031- 6DV62вЂ‘0AA0	6RM8075- 6DV62вЂ‘0AA0	6RM8078- 6DV62вЂ‘0AA0	6RM8081- 6DV62вЂ‘0AA0
Rated armature supply voltage	V	3 AC 400 (+15 %/–20 %)
Rated armature input current	A	104	174	232	332
Cooling air requirement	mі/h	800	800	800	600
Sound pressure level	dB (A)	72	72	72	74
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	420	420	420	420
Rated DC current	A	125	210	280	400
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	52.5	88.2	117.6	168
Power loss at rated DC current	W	726	1 202	1 557	2 226
Rated DC field voltage	V	max. 325	max. 325	max. 325	max. 325
Rated DC field current	A	10	15	15	25
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	1 Г— 50	1 Г— 95	1 Г— 120	1 Г— 185
Armature circuit connection	Number Г— mm²	1 Г— 50	1 Г— 95	2 Г— 50	1 Г— 185
Field circuit connection	Number Г— mm²	1 Г— 1.5	1 Г— 2.5	1 Г— 2.5	1 Г— 4
Auxiliary power supply	mm²	2.5	4	4	10
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	125	200	250	355
Max. permissible short-circuit current	kA	50²⁾	50³⁾	50³⁾	50
Auxiliary power supply	A	16	25	25	50
Max. permissible short-circuit current	kA	30	30	30	30
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	600	600	600	800
Height	mm	2 326	2 326	2 326	2 200
Depth	mm	600	600	600	600
Size		BC	BC	BC	CC
Weight, approx.	kg	240	263	273	320

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 43 kA.

³⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 25 kA.

SINAMICS DC MASTER Cabinet for 400 V 3 AC, 600 to 1 600 A, four-quadrant operation

		Type
		6RM8085- 6DV62вЂ‘0AA0	6RM8087- 6DV62вЂ‘0AA0	6RM8091- 6DV62вЂ‘0AA0	6RM8093- 4DV62вЂ‘0AA0
Rated armature supply voltage	V	3 AC 400 (+15 %/–20 %)
Rated armature input current	A	498	706	996	1 328
Cooling air requirement	mі/h	600	600	1 000	3 000
Sound pressure level	dB (A)	74	74	76	78
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	420	420	420	420
Rated DC current	A	600	850	1 200	1 600
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	252	357	504	672
Power loss at rated DC current	W	2 984	3 939	4 697	6 430
Rated DC field voltage	V	max. 325	max. 325	max. 390	max. 390
Rated DC field current	A	25	30	30	40
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	2 Г— 150	2 Г— 240	4 Г— 150	6 Г— 150
Armature circuit connection	Number Г— mm²	2 Г— 150	4 Г— 95	4 Г— 185	8 Г— 95
Field circuit connection	Number Г— mm²	1 Г— 4	1 Г— 4	1 Г— 4	1 Г— 6
Auxiliary power supply	mm²	10	16	16	35
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	500	710	–²⁾	–²⁾
Max. permissible short-circuit current	kA	50	50	65	75
Auxiliary power supply	A	50	63	63	100
Max. permissible short-circuit current	kA	30	30	30	50
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	800	1 200	1 200	1 400
Height	mm	2 200	2 200	2 200	2 200
Depth	mm	600	600	600	600
Size		CC	DC	DC	EC
Weight, approx.	kg	340	490	570	780

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

SINAMICS DC MASTER Cabinet for 400 V 3 AC, 2 000 to 3 000 A, four-quadrant operation

		Type
		6RM8095- 4DV62вЂ‘0AA0	6RM8098- 4DV62вЂ‘0AA0
Rated armature supply voltage	V	3 AC 400 (+15 %/–20 %)
Rated armature input current	A	1 660	2 490
Cooling air requirement	mі/h	3 000	3 000
Sound pressure level	dB (A)	78	78
Rated frequency	Hz	45 ... 65	45 ... 65
Rated DC voltage	V	420	420
Rated DC current	A	2 000	3 000
Overload capability	x Г— I_n	1.8	1.8
Rated power	kW	840	1 260
Power loss at rated DC current	W	7 618	11 747
Rated DC field voltage	V	max. 390	max. 390
Rated DC field current	A	40	40
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	6 Г— 185	8 Г— 240
Armature circuit connection	Number Г— mm²	8 Г— 150	8 Г— 240
Field circuit connection	Number Г— mm²	1 Г— 6	1 Г— 6
Auxiliary power supply	mm²	35	35
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	–²⁾	–²⁾
Max. permissible short-circuit current	kA	75	75
Auxiliary power supply	A	100	100
Max. permissible short-circuit current	kA	50	50
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	1 400	1 400
Height	mm	2 200	2 200
Depth	mm	600	600
Size		EC	EC
Weight, approx.	kg	820	950

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

SINAMICS DC MASTER Cabinet for 480 V 3 AC, 15 to 90 A, four-quadrant operation

		Type
		6RM8013- 6FV62вЂ‘0AA0	6RM8018- 6FV62вЂ‘0AA0	6RM8025- 6FV62вЂ‘0AA0	6RM8028- 6FV62вЂ‘0AA0
Rated armature supply voltage	V	3 AC 480 (+10 %/–20 %)
Rated armature input current	A	12	25	50	75
Cooling air requirement	mі/h	800	800	800	800
Sound pressure level	dB (A)	72	72	72	72
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	500	500	500	500
Rated DC current	A	15	30	60	90
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	6.3	15	30	45
Power loss at rated DC current	W	292	377	534	609
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	3	5	10	10
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	1 Г— 2.5	1 Г— 6	1 Г— 16	1 Г— 25
Armature circuit connection	Number Г— mm²	1 Г— 2.5	1 Г— 6	1 Г— 16	1 Г— 25
Field circuit connection	Number Г— mm²	1 Г— 1.5	1 Г— 1.5	1 Г— 1.5	1 Г— 1.5
Auxiliary power supply	mm²	2.5	2.5	2.5	2.5
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	20	32	63	80
Max. permissible short-circuit current	kA	50²⁾	50²⁾	50²⁾	50²⁾
Auxiliary power supply	A	16	16	16	16
Max. permissible short-circuit current	kA	30	30	30	30
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	600	600	600	600
Height	mm	2 326	2 326	2 326	2 326
Depth	mm	600	600	600	600
Size		BC	BC	BC	BC
Weight, approx.	kg	210	215	233	238

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 43 kA.

SINAMICS DC MASTER Cabinet for 480 V 3 AC, 125 to 450 A, four-quadrant operation

		Type
		6RM8031- 6FV62вЂ‘0AA0	6RM8075- 6FV62вЂ‘0AA0	6RM8078- 6FV62вЂ‘0AA0	6RM8082- 6FV62вЂ‘0AA0
Rated armature supply voltage	V	3 AC 480 (+10 %/–20 %)
Rated armature input current	A	104	174	232	374
Cooling air requirement	mі/h	800	800	800	600
Sound pressure level	dB (A)	72	72	72	74
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	500	500	500	500
Rated DC current	A	125	210	280	450
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	62.5	105	140	225
Power loss at rated DC current	W	748	1 275	1 556	2 467
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	10	15	15	25
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	1 Г— 50	1 Г— 95	1 Г— 120	2 Г— 120
Armature circuit connection	Number Г— mm²	1 Г— 50	1 Г— 95	2 Г— 50	2 Г— 95
Field circuit connection	Number Г— mm²	1 Г— 1.5	1 Г— 2.5	1 Г— 2.5	1 Г— 4
Auxiliary power supply	mm²	2.5	4	4	10
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	125	200	250	400
Max. permissible short-circuit current	kA	50²⁾	50³⁾	50³⁾	50
Auxiliary power supply	A	16	25	25	50
Max. permissible short-circuit current	kA	30	30	30	30
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	600	600	600	800
Height	mm	2 326	2 326	2 326	2 200
Depth	mm	600	600	600	600
Size		BC	BC	BC	CC
Weight, approx.	kg	240	273	273	340

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 43 kA.

³⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 25 kA.

SINAMICS DC MASTER Cabinet for 480 V 3 AC, 600 to 1 200 A, four-quadrant operation

		Type
		6RM8085- 6FV62вЂ‘0AA0	6RM8087- 6FV62вЂ‘0AA0	6RM8091- 6FV62вЂ‘0AA0
Rated armature supply voltage	V	3 AC 480 (+10 %/–20 %)
Rated armature input current	A	498	706	996
Cooling air requirement	mі/h	600	600	1 000
Sound pressure level	dB (A)	74	74	76
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	500	500	500
Rated DC current	A	600	850	1 200
Overload capability	x Г— I_n	1.8	1.8	1.8
Rated power	kW	300	425	600
Power loss at rated DC current	W	3 197	4 303	4 857
Rated DC field voltage	V	max. 390	max. 390	max. 390
Rated DC field current	A	25	30	30
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	2 Г— 150	2 Г— 240	4 Г— 150
Armature circuit connection	Number Г— mm²	2 Г— 150	4 Г— 95	4 Г— 185
Field circuit connection	Number Г— mm²	1 Г— 4	1 Г— 4	1 Г— 4
Auxiliary power supply	mm²	10	16	16
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	500	710	–²⁾
Max. permissible short-circuit current	kA	50	50	65
Auxiliary power supply	A	50	63	63
Max. permissible short-circuit current	kA	30	30	30
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	800	1 200	1 200
Height	mm	2 200	2 200	2 200
Depth	mm	600	600	600
Size		CC	DC	DC
Weight, approx.	kg	355	500	570

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

SINAMICS DC MASTER Cabinet for 575 V 3 AC, 60 to 400 A, four-quadrant operation

		Type
		6RM8025- 6GV62вЂ‘0AA0	6RM8031- 6GV62вЂ‘0AA0	6RM8075- 6GV62вЂ‘0AA0	6RM8081- 6GV62вЂ‘0AA0
Rated armature supply voltage	V	3 AC 575 (+10 %/–20 %)
Rated armature input current	A	50	104	174	332
Cooling air requirement	mі/h	800	800	800	600
Sound pressure level	dB (A)	72	72	72	74
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	600	600	600	600
Rated DC current	A	60	125	210	400
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	36	75	126	240
Power loss at rated DC current	W	509	797	1 320	2 534
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	10	10	15	25
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	1 Г— 16	1 Г— 50	1 Г— 95	1 Г— 185
Armature circuit connection	Number Г— mm²	1 Г— 16	1 Г— 50	1 Г— 95	1 Г— 185
Field circuit connection	Number Г— mm²	1 Г— 1.5	1 Г— 2.5	1 Г— 2.5	1 Г— 4
Auxiliary power supply	mm²	2.5	2.5	4	10
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	63	125	200	355
Max. permissible short-circuit current	kA	50²⁾	50²⁾	50³⁾	50
Auxiliary power supply	A	16	16	25	50
Max. permissible short-circuit current	kA	30	30	30	30
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	600	600	600	800
Height	mm	2 326	2 326	2 326	2 200
Depth	mm	600	600	600	600
Size		BC	BC	BC	CC
Weight, approx.	kg	233	240	273	335

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 43 kA.

³⁾ With option L00 (radio interference suppression filter), the maximum permissible short-circuit current is reduced to 25 kA.

SINAMICS DC MASTER Cabinet for 575 V 3 AC, 600 to 1 600 A, four-quadrant operation

		Type
		6RM8085- 6GV62вЂ‘0AA0	6RM8087- 6GV62вЂ‘0AA0	6RM8090- 6GV62вЂ‘0AA0	6RM8093- 4GV62вЂ‘0AA0
Rated armature supply voltage	V	3 AC 575 (+10 %/–20 %)
Rated armature input current	A	498	706	913	1 328
Cooling air requirement	mі/h	600	600	1 000	3 000
Sound pressure level	dB (A)	74	74	76	78
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	600	600	600	600
Rated DC current	A	600	850	1 100	1 600
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	360	510	660	960
Power loss at rated DC current	W	3 290	4 112	4 583	6 988
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	25	30	30	40
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	2 Г— 150	2 Г— 240	4 Г— 150	6 Г— 150
Armature circuit connection	Number Г— mm²	2 Г— 150	4 Г— 95	4 Г— 120	8 Г— 95
Field circuit connection	Number Г— mm²	1 Г— 4	1 Г— 4	1 Г— 4	1 Г— 6
Auxiliary power supply	mm²	10	16	16	35
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	500	710	–²⁾	–²⁾
Max. permissible short-circuit current	kA	50	50	65	75
Auxiliary power supply	A	50	63	63	100
Max. permissible short-circuit current	kA	30	30	30	50
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	800	1 200	1 200	1 400
Height	mm	2 200	2 200	2 200	2 200
Depth	mm	600	600	600	600
Size		CC	DC	DC	EC
Weight, approx.	kg	355	515	600	795

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

SINAMICS DC MASTER Cabinet for 575 V 3 AC, 2 000 to 2 800 A, four-quadrant operation

		Type
		6RM8095- 4GV62вЂ‘0AA0	6RM8096- 4GV62вЂ‘0AA0	6RM8097- 4GV62вЂ‘0AA0
Rated armature supply voltage	V	3 AC 575 (+10 %/–20 %)
Rated armature input current	A	1 660	1 826	2 324
Cooling air requirement	mі/h	3 000	3 000	3 000
Sound pressure level	dB (A)	78	78	78
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	600	600	600
Rated DC current	A	2 000	2 200	2 800
Overload capability	x Г— I_n	1.8	1.8	1.8
Rated power	kW	1 200	1 320	1 680
Power loss at rated DC current	W	8 090	8 408	11 937
Rated DC field voltage	V	max. 390	max. 390	max. 390
Rated DC field current	A	40	40	40
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	6 Г— 185	8 Г— 150	8 Г— 240
Armature circuit connection	Number Г— mm²	8 Г— 150	8 Г— 185	8 Г— 240
Field circuit connection	Number Г— mm²	1 Г— 6	1 Г— 6	1 Г— 6
Auxiliary power supply	mm²	35	35	35
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	–²⁾	–²⁾	–²⁾
Max. permissible short-circuit current	kA	75	75	75
Auxiliary power supply	A	100	100	100
Max. permissible short-circuit current	kA	50	50	50
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	1 400	1 400	1 400
Height	mm	2 200	2 200	2 200
Depth	mm	600	600	600
Size		EC	EC	EC
Weight, approx.	kg	850	950	1 030

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

SINAMICS DC MASTER Cabinet for 690 V 3 AC, 760 to 2 600 A, four-quadrant operation

		Type
		6RM8086- 6KV62вЂ‘0AA0	6RM8090- 6KV62вЂ‘0AA0	6RM8093- 4KV62вЂ‘0AA0	6RM8095- 4KV62вЂ‘0AA0	6RM8097- 4KV62вЂ‘0AA0
Rated armature supply voltage	V	3 AC 690 (+10 %/–20 %)
Rated armature input current	A	631	830	1 245	1 660	2 158
Cooling air requirement	mі/h	600	1 000	3 000	3 000	3 000
Sound pressure level	dB (A)	74	76	78	78	78
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	725	725	725	725	725
Rated DC current	A	760	1 000	1 500	2 000	2 600
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8	1.8
Rated power	kW	551	725	1 087.5	1 450	1 885
Power loss at rated DC current	W	4 352	4 642	7 627	9 175	12 007
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	30	30	40	40	40
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	2 Г— 240	4 Г— 120	6 Г— 120	6 Г— 185	8 Г— 240
Armature circuit connection	Number Г— mm²	4 Г— 95	4 Г— 120	8 Г— 95	8 Г— 150	8 Г— 240
Field circuit connection	Number Г— mm²	1 Г— 4	1 Г— 4	1 Г— 6	1 Г— 6	1 Г— 6
Auxiliary power supply	mm²	16	16	35	35	35
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	630	–²⁾	–²⁾	–²⁾	–²⁾
Max. permissible short-circuit current	kA	50	65	75	75	75
Auxiliary power supply	A	63	63	100	100	100
Max. permissible short-circuit current	kA	30	30	50	50	50
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	1 200	1 200	1 400	1 400	1 600
Height	mm	2 200	2 200	2 200	2 200	2 200
Depth	mm	600	600	600	600	600
Size		DC	DC	EC	EC	FC
Weight, approx.	kg	515	600	815	850	1 070

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

SINAMICS DC MASTER Cabinet for 830 V 3 AC, 950 to 1 900 A and 950 V 3 AC, 2 200 V, four-quadrant operation

		Type
		6RM8088- 6LV62вЂ‘0AA0	6RM8093- 4LV62вЂ‘0AA0	6RM8095- 4LV62вЂ‘0AA0	6RM8096- 4MV62вЂ‘0AA0
Rated armature supply voltage	V	3 AC 830 (+10 %/–20 %)			3 AC 950 (+15%/–20%)
Rated armature input current	A	789	1 245	1 577	1 826
Cooling air requirement	mі/h	1 000	3 000	3 000	3 000
Sound pressure level	dB (A)	76	78	78	78
Rated frequency	Hz	45 ... 65	45 ... 65	45 ... 65	45 ... 65
Rated DC voltage	V	875	875	875	1 000
Rated DC current	A	950	1 500	1 900	2 200
Overload capability	x Г— I_n	1.8	1.8	1.8	1.8
Rated power	kW	831.25	1 312.5	1 662.5	2 200
Power loss at rated DC current	W	4 911	8 039	9 986	12 957
Rated DC field voltage	V	max. 390	max. 390	max. 390	max. 390
Rated DC field current	A	30	40	40	40
Max. connection cross-sections¹⁾
Line connection (3 phases and PE)	Number Г— mm²	4 Г— 120	6 Г— 120	6 Г— 185	8 Г— 150
Armature circuit connection	Number Г— mm²	4 Г— 150	8 Г— 95	8 Г— 150	8 Г— 185
Field circuit connection	Number Г— mm²	1 Г— 4	1 Г— 6	1 Г— 6	1 Г— 6
Auxiliary power supply	mm²	16	35	35	35
Max. permissible fusing on the customer's side (NH fuse gL/gG)
Power connections	A	–²⁾	–²⁾	–²⁾	–²⁾
Max. permissible short-circuit current	kA	50	50	50	50
Auxiliary power supply	A	63	100	100	100
Max. permissible short-circuit current	kA	30	50	50	50
Normal ambient temperature in operation	°C	See the table on installation altitude and ambient temperature
Dimensions
Width	mm	1 200	1 400	1 400	1 600
Height	mm	2 200	2 200	2 200	2 200
Depth	mm	600	600	600	600
Size		DC	EC	EC	FC
Weight, approx.	kg	600	845	925	1 070

¹⁾ With cable lugs according to DIN 46234 or DIN 46235; for units from 2 600 to 3 000 A, motor cables are only directly connected at the DC converter using cable lugs according to DIN 46234.

²⁾ It must be ensured that the maximum permissible short-circuit current at the supply switch of the drive cabinet is not exceeded.

skener.ru

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
Бесконтактные выключатели Конечные выключатели Оптические датчики Энкодеры

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FS - Установка умягчения

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FK - Установка обезжелезивания