Rated voltages

380 ... 480 V 3 AC, ±10 % (-15 % < 1 min)

500 ... 690 V 3 AC, ±10 % (-15 % < 1 min)

Line supply types

Grounded TN/TT systems and non-grounded IT systems

Line frequency

47 ... 63 Hz

Overvoltage category

III to EN 61800-5-1

Electronics power supply

24 V DC, -15 % +20 %
implemented as PELV circuit in accordance with EN 61800-5-1
Ground = negative pole grounded via the electronics

Rated short-circuit current SCCR (Short Circuit Current Rating)

according to UL508C (up to 600 V), in conjunction with the specified fuses or circuit breakers

Rated power

• 1.1 ... 447 kW

65 kA

• 448 ... 671 kW

84 kA

• 672 ... 1193 kW

170 kA

• > 1194 kW

200 kA

Control method

Vector/servo control with and without encoder or V/f control

Fixed speeds

15 fixed speeds plus 1 minimum speed, parameterizable (in the default setting, 3 fixed setpoints plus 1 minimum speed are selectable using terminal block/PROFIBUS/PROFINET)

Skipped speed ranges

4, parameterizable

Setpoint resolution

0.001 rpm digital (14 bits + sign)
12 bit analog

Braking operation

With Active Line Modules and Smart Line Modules, four-quadrant operation as standard (energy recovery).

With Basic Line Modules, single-quadrant operation as standard.

Braking when the power fails using an optional braking module.

Degree of protection

IP00 or IP20 dependent on type

Protection class

I acc. to EN 61800-5-1

Touch protection

EN 50274 / BGV A3 (for the intended purpose)

Type of cooling

Liquid cooling with integrated heat exchanger in aluminum or stainless steel version

Cooling circuit

• System pressure with respect to the atmosphere, max.

600 kPa

• Pressure drop at rated volumetric flow

70 kPa

• Recommended pressure range

80 … 200 kPa

• Inlet temperature of liquid coolant

Dependent on the ambient temperature, condensation is not permitted

0 … 45 °C without derating

> 45 … 50 °C, see derating data

Temperature range between 0 °C and 5 °C only with antifreeze

(recommended antifreeze "Antifrogen N" from the Clariant company)

Coolant quality

for aluminum heat sinks

for stainless steel heat sinks

• Coolant basis

Deionized water with reduced conductivity (5 ... 10 ?S/cm), e.g.:

• "Battery water" with 0.2 % inhibitor, Nalco TRAC100 (manufacturer: Nalco) or Antifrogen N with a component X of 20 % < X ? 45 % (manufacturer: Clariant)
• or filtered drinking water with 0.2 % inhibitor, Nalco TRAC100 (manufacturer: Nalco) or Antifrogen N with a component X of 20 % < X ? 45 % (manufacturer: Clariant) with the following quality:

Filtered drinking water with the following quality:

• Chloride ions

< 40 mg/l, if required, achieved by adding deionized water

< 200 mg/l

• Sulfate ions

< 50 mg/l

< 240 mg/l

• Nitrate ions

< 50 mg/l

< 50 mg/l

• pH value

5.5 ... 8.0

6.5 ... 9.0

• Conductivity

< 500 ?S/cm

< 2000 ?S/cm

• Total hardness

< 1.7 mmol/l

< 1.7 mmol/l

• Dissolved substances

< 340 mg/l

< 340 mg/l

• Grain size of particles in the water

< 100 ?m

< 100 ?m

The coolant definition specified here should only be considered as recommendation. For units that have been shipped, the information and data provided in the equipment manual supplied must be observed!

Ambient temperature (air)

-40 ... +70 °C

Class 1K3
acc. to EN 60721-3-1

-40 ... +70 °C

Class  2K4
acc. to EN 60721-3-2

Line-side components, Power Modules, Line Modules and Motor Modules:

0 … 45 °C without derating
> 45 … 50 °C , see derating data

Control Units, supplementary system components, DC link components and Sensor Modules

0 … 50 °C

Relative humidity

Condensation, splashwater, and ice formation not permitted (EN 60204, Part 1)

5 ... 95 %

Class 1K4
acc. to EN 60721-3-1

max. 95 % at 40 °C

Class 2K3
acc. to EN 60721-3-2

5 ... 95 % ²⁾

Class 3K3
acc. to EN 60721-3-3

Environmental class/harmful chemical substances

Class 1C2
acc. to EN 60721-3-1

Class 2C2
acc. to EN 60721-3-2

Class 3C2
acc. to EN 60721-3-3

Organic/biological influences

Class 1B1
acc. to EN 60721-3-1

Class 2B1
acc. to EN 60721-3-2

Class 3B1
acc. to EN 60721-3-3

Degree of pollution

2 acc. to EN 61800-5-1

2 acc. to EN 61800-5-1

2 acc. to EN 61800-5-1

Installation altitude

Up to 2000 m above sea level without derating
> 2000 m above sea level, see derating data

Up to 2000 m above sea level without derating
> 2000 m above sea level, see derating data

Up to 2000 m above sea level without derating
> 2000 m above sea level, see derating data

Mechanical stability

Storage ¹⁾

Transport ¹⁾

Operation

Vibration load

Class  2M2
acc. to EN 60721-3-2

Test values
acc. to EN 60068-2-6 test Fc:

• 10 ... 58 Hz with constant deflection 0.075 mm
• 58 ... 150 Hz with the constant acceleration 9.81 m/s2 (1 ? g)

Shock load Class

Class  2M2
acc. to EN 60721-3-2

Test values
acc. to EN 60068-2-27 test Ea:
98 m/s2 (10 ? g)/20 ms

Compliance with standards

Conformances/approvals, according to

CE (EMC Directive No. 2004/108/EC and Low-Voltage Directive No. 2006/95/EC) cULus (only for devices connected to line supply voltages 380 ... 480 V 3 AC and 500 ... 600 V 3 AC)

Radio interference suppression

SINAMICS drive converter systems are not designed for connection to the public network (first environment). Radio interference suppression is compliant with the EMC product standard for variable-speed drives EN 61800-3, "Second environment" (industrial line supplies). The equipment can cause electromagnetic interference when it is connected to the public network. However, if supplementary measures are taken (e.g. > line filter), it can also be operated in the "first environment".