1PH4 for SINAMICS S120 for machine tools. Опции. Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на 1PH4 for SINAMICS S120 for machine tools

| | | | | | | |

1PH4 for SINAMICS S120 for machine tools

Description	Order code
Bearing version (view drive end) (standard = duplex bearing)
Single bearing for coupling, for low to medium cantilever forces or planetary gearboxes (e.g. mounting of a ZF gearbox 2LG43...)⁵⁾⁶⁾	K00
Vibration magnitude in accordance with EN 60034-14 (IEC 60034-14) (standard = vibration magnitude grade R, duplex bearing)
Grade S with duplex bearing⁷⁾	K05⁸⁾
Grade S with single bearing⁷⁾	K02⁸⁾
Grade SR with single bearing⁷⁾	K03⁸⁾
Shaft and flange accuracy in accordance with DIN 42955 (IEC 60072-1) (standard = tolerance N)
Tolerance R⁹⁾	K04
Shaft extension DE (standard = full-key balancing with keyway)
Plain shaft	K42
Half-key balancing	L69
Shaft sealDE¹⁰⁾
Radial shaft sealing ring, oil-tight, IP65	K18
Brake⁶⁾
With holding brake mounted on DE	G46
Terminal box location view DE (standard = top)
Right side, cable entry from below⁶⁾	K09¹¹⁾
Left side, cable entry from below⁶⁾	K10¹¹⁾
Rotation of terminal box on its own axis
By 90°, cable entry form drive end¹²⁾	K83
By 90°, cable entry form non-drive end¹²⁾	K84
By 180°, cable entry form above¹²⁾	K85¹¹⁾
Speed¹³⁾
With increased maximum speed and half-key balancing	L37
Other
Second rating plate, separately packed	K31

When ordering a motor with options, -Z should be added to the order number. The order code should also be specified for each additional required option.

Order codes must not be repeated in plain text in the order.

Order No.1PH4135-4NF26-Z

Order codesK05 +K09 +K31

¹⁾ For continuous duty (with 30 %n_max, 60 % 2/3n_max, 10 % standstill) for a duty cycle time of 10 min. For maintenance intervals for motors and components, see the 1PH Motors Configuration Manual.

²⁾ Bearing version for duplex bearing.

³⁾ Bearing version for single bearing.

⁴⁾ Bearing version for increased speed using option L37.

⁵⁾ Vibration magnitude grades S, SR and mounting position IM V35 not possible for integrated gearbox. Use order code K00 + G97 for old ZF gearbox 2LG42... (for gearbox selection, see Gearboxes).

⁶⁾ Options gearbox assembly, brake assembly and terminal box location mutually exclude each other.

⁷⁾ Options K05, K02 and K03 mutually exclude each other.

⁸⁾ Automatically includes option K04.

⁹⁾ Increased shaft accuracy.

¹⁰⁾ Only appropriate if the sealing ring is occasionally lubricated with oil spray/mist.

¹¹⁾ Options K09 or K10 cannot be combined with K85.

¹²⁾ Options K83, K84 and K85 mutually exclude each other.

¹³⁾ Version for increased maximum speed includes vibration magnitude grade SR and half-key balancing. The following option is not possible: Shaft seal.