Standard functions |
Speed, max. | 15000 rpm | 10000 rpm |
Enclosure | Cartridge with flange mounting | Cartridge with flange mounting |
Operating position | Horizontal/vertical | Horizontal/vertical |
Tool holder | HSK A63 | SK 40 for tools with asymmetrical slot nuts |
Tool clamping device | - Release using pneumatic cylinder, 6 bar
- Clamp using cup-spring assembly
| - Release using pneumatic cylinder, 6 bar
- Clamp using cup-spring assembly
|
Tool taper cleaning | Compressed air through draw-bar 5 ... 6 bar | Compressed air through draw-bar 5 ... 6 bar |
Cooling with water | - Max. 5 bar, 10 l/min (2.64 US gallons/min)
- Max. 25 % corrosion protection agent
Clariant Antifrogen N or Tyfocor - Filter grade 100 μm
| - Max. 5 bar, 10 l/min (2.64 US gallons/min)
- Max. 25 % corrosion protection agent
Clariant Antifrogen N or Tyfocor - Filter grade 100 μm
|
Recommended coolant inlet temperature, approx. | 25 °C (77 °F)
(depending on the ambient temperature) | 25 °C (77 °F)
(depending on the ambient temperature) |
Standard protection -
temperature monitoring | - Motor thermal sensor KTY84-130
- PTC for full thermal protection
- NTC PT3-51F
- NTC K227
| - Motor thermal sensor KTY84-130
|
Stator winding insulation in accordance with
EN 60034-1 (IEC 600034-1) | Temperature class 155 (F) for a coolant inlet temperature of 25 °C (77 °F) | Temperature class 155 (F) for a coolant inlet temperature of 25 °C (77 °F) |
Degree of protection
in accordance with IEC 60034-5 | IP64 (in working area)
IP53 (behind the spindle flange) | IP64 (in working area)
IP53 (behind the spindle flange) |
Bearing lubrication | Grease, permanent lubrication | Grease, permanent lubrication |
Front bearing seal | Sealing air 1 ... 1.5 m3/h, filter grade 8 µm | Sealing air 1 ... 1.5 m3/h, filter grade 8 µm |
Encoder system | Hollow-shaft measuring system, incremental, sin/cos 1 Vpp 256 S/R with zero mark | Hollow-shaft measuring system, incremental, sin/cos 1 Vpp 256 S/R with zero mark |
Clamping status monitoring | | |
| - Tool clamped
- Draw-bar in the release position
- Clamped without tool
| – |
| - Position of release piston
| - Tool clamped
- Draw-bar in the release position
- Clamped without tool
|
Connections for the media | | |
| 2 × hose plug-in connector, Ø 12 mm/10 mm (0.47 in/0.39 in) | 2 × G 1/2“ (Ø 9 mm) (0.35 in)) |
| 1 × G 1/8“ radial/Ø 5 mm (0.20 in) axial | 1 × G 1/8“ (Ø 8 mm) (0.31 in)) |
| 1 × G 1/4“ | 1 × G 1/4“ |
| 1 × G 1/4“ | 1 × M16 × 1,5 |
| 1 × G 1/8“ | 1 × G 1/8“ |
Electrical connections | - Power via cable 1.5 m (4.92 ft)
- Sensors through signal plug
| - Power via cable 1.5 m (4.92 ft)
- Sensors through signal plug
|
Options |
Increased max. speed | 18000 rpm | 15000 rpm (with HSK A63) |
Internal tool cooling | - 50 bar, up to 54 l/min(11.89 US gallons/min)
- Filter grade 50 μm according to -/16/13 ISO 4406
- 1 × G1/4“ coolant
- 1 × G1/8“ leakage
| - 50 bar, up to 54 l/min (11.89 US gallons/min)
- Filter grade 50 μm according to -/16/13 ISO 4406
- 1 × G1/4“ coolant
- 1 × G1/8“ leakage
|
External tool cooling | - Ring with 6 adjustable nozzles
- 5 bar
- Filter grade 50 μm in according to -/16/13 ISO 4406
| – |
Tool clamping device | - Release using hydraulic cylinder, 80 bar
- Clamping using cup-spring assembly
- 1 × G 1/4“, release tool
- 1 × G 1/4“, clamp tool
| – |
Tool interface | – | BT 40, CAT 40, HSK A63 |
