Motor Modules . Технические данные. Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на Motor Modules

| | | | | |

Motor Modules

General technical specifications

Electrical specifications
Efficiency	>98.5 %
DC link voltage (up to 2000 m (6562 ft) above sea level)	510 ... 720 V DC (line supply voltage 380 ... 480 V 3 AC) or 675 ... 1035 V DC (line supply voltage 500 ... 690 V 3 AC)
Output frequency ¹⁾
Control mode Servo	0 ... 550 Hz
Control mode Vector	0 ... 550 Hz
Control mode V/f	0 ... 550 Hz
Safety Integrated	Safety Integrity Level 2 (SIL2) acc. to IEC 61508, Performance Level d (PLd) acc. to EN ISO 13849-1 and Control Category 3 acc. to EN ISO 13849?1

¹⁾ Please note:

• The correlation between the maximum output frequency, pulse frequency and current derating. Higher output frequencies on request For further information, see https://support.industry.siemens.com/cs/document/104020669

• The correlation between the minimum output frequency and permissible output current (current derating). Information is provided in the SINAMICS Low Voltage Engineering Manual.

Line voltage 380 ... 480 V 3 AC DC link voltage 510 ... 720 V DC		Motor Modules
		6SL3320-1TE32-1AA3	6SL3320-1TE32-6AA3	6SL3320-1TE33-1AA3	6SL3320-1TE33-8AA3	6SL3320-1TE35-0AA3
Type rating
At I_L (50 Hz 400 V) ¹⁾	kW	110	132	160	200	250
At I_H (50 Hz 400 V) ¹⁾	kW	90	110	132	160	200
At I_L (60 Hz 460 V) ²⁾	hp	150	200	250	300	400
At I_H (60 Hz 460 V) ²⁾	hp	150	200	200	250	350
Output current
Rated current I_{rated O}	A	210	260	310	380	490
Base-load current I_L³⁾	A	205	250	302	370	477
Base-load current I_H⁴⁾	A	178	233	277	340	438
Maximum current I_max A	A	307	375	453	555	715
DC link current
Rated current I_rated DC when supplied via
Basic/Smart Line Module	A	252	312	372	456	588
Active Line Module	A	227	281	335	411	529
Base-load current I_L DC ³⁾ when supplied via
Basic/Smart Line Module	A	245	304	362	444	573
Active Line Module	A	221	273	326	400	515
Base-load current I_{H DC}⁴⁾ when supplied via
Basic/Smart Line Module	A	224	277	331	405	523
Active Line Module	A	202	250	298	365	470
Current demand
24 V DC auxiliary power supply	A	0.8	0.8	0.9	0.9	0.9
400 V AC	A	0.63	1.13	1.8	1.8	1.8
DC link capacitance	?F	4200	5200	6300	7800	9600
Pulse frequency ⁵⁾
Rated frequency	kHz	2	2	2	2	2
Pulse frequency, max.
Without current derating	kHz	2	2	2	2	2
With current derating	kHz	8	8	8	8	8
Power loss, max. ⁶⁾
At 50 Hz 400 V	kW	1.86	2.5	2.96	3.67	4.28
At 60 Hz 460 V	kW	1.94	2.6	3.1	3.8	4.5
Cooling air requirement	m³/s (ft³/s)	0.17 (6.00)	0.23 (8.12)	0.36 (12.7)	0.36 (12.7)	0.36 (12.7)
Sound pressure level L_pA (1 m) at 50/60 Hz	dB	64/67	71/71	69/73	69/73	69/73
DC link connection DCP, DCN		M10 screw	M10 screw	M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 185	2 ? 185	2 ? 240	2 ? 240	2 ? 240
Connection for Braking Module DCPA, DCNA⁷⁾		M6 threaded bolt	M6 threaded bolt	M6 threaded bolt	M6 threaded bolt	M6 threaded bolt
Connection for dv/dt filter DCPS, DCNS		M8 screw	M8 screw	M8 screw	M8 screw	M8 screw
Conductor cross section, max. (IEC)	mm²	1 ? 35	1 ? 35	1 ? 70	1 ? 70	1 ? 70
Motor connection U2, V2, W2		M10 screw	M10 screw	M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 185	2 ? 185	2 ? 240	2 ? 240	2 ? 240
Cable length, max. ⁸⁾
Shielded	m (ft)	300 (984)	300 (984)	300 (984)	300 (984)	300 (984)
Unshielded	m (ft)	450 (1476)	450 (1476)	450 (1476)	450 (1476)	450 (1476)
PE1/GND connection		M10 screw	M10 screw	M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 185	2 ? 185	2 ? 240	2 ? 240	2 ? 240
PE2/GND connection		M10 screw	M10 screw	M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 185	2 ? 185	2 ? 240	2 ? 240	2 ? 240
Degree of protection		IP20	IP20	IP20	IP20	IP20
Dimensions
Width	mm (in)	326 (12.8)	326 (12.8)	326 (12.8)	326 (12.8)	326 (12.8)
Height	mm (in)	1400 (55.1)	1400 (55.1)	1533 (60.3)	1533 (60.3)	1533 (60.3)
Depth	mm (in)	356 (14.0)	356 (14.0)	545 (21.5)	545 (21.5)	545 (21.5)
Weight, approx.	kg (lb)	95 (209)	95 (209)	136 (300)	136 (300)	136 (300)
Frame size		FX	FX	GX	GX	GX

¹⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 400 V 3 AC 50 Hz.

²⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 460 V 3 AC 60 Hz.

³⁾ The base-load current I_L is based on a duty cycle of 110 % for 60 s or 150 % for 10 s with a duty cycle duration of 300 s.

⁴⁾ The base-load current I_H is based on a duty cycle of 150 % for 60 s or 160 % for 10 s with a duty cycle duration of 300 s.

⁵⁾Information regarding the correlation between the pulse frequency and maximum output current/output frequency is provided in the SINAMICS Low Voltage Engineering Manual.

⁶⁾ The specified power loss represents the maximum value at 100% utilization. The value is lower under normal operating conditions.

⁷⁾ The connecting cables are included in the scope of supply of the Braking Module.

⁸⁾ Total of all motor cables and DC link. Longer cable lengths for specific configurations are available on request. For additional information, please refer to the SINAMICS Low Voltage Engineering Manual.

Line voltage 380 ... 480 V 3 AC DC link voltage 510 ... 720 V DC		Motor Modules
		6SL3320-1TE36-1AA3	6SL3320-1TE37-5AA3	6SL3320-1TE38-4AA3
Type rating
At I_L (50 Hz 400 V) ¹⁾	kW	315	400	450
At I_H (50 Hz 400 V) ¹⁾	kW	250	315	400
At I_L (60 Hz 460 V) ²⁾	hp	500	600	700
At I_H (60 Hz 460 V) ²⁾	hp	350	450	600
Output current
Rated current I_{rated O}	A	605	745	840
Base-load current I_L³⁾	A	590	725	820
Base-load current I_H⁴⁾	A	460	570	700
Maximum current I_max A	A	885	1087	1230
DC link current
Rated current I_rated DC when supplied via
Basic/Smart Line Module	A	726	894	1008
Active Line Module	A	653	805	907
Base-load current I_L DC ³⁾ when supplied via
Basic/Smart Line Module	A	707	871	982
Active Line Module	A	636	784	884
Base-load current I_{H DC}⁴⁾ when supplied via
Basic/Smart Line Module	A	646	795	897
Active Line Module	A	581	716	807
Current demand
24 V DC auxiliary power supply	A	1.0	1.0	1.0
400 V AC	A	3.6	3.6	3.6
DC link capacitance	?F	12600	15600	16800
Pulse frequency ⁵⁾
Rated frequency	kHz	1.25	1.25	1.25
Pulse frequency, max.
Without current derating	kHz	1.25	1.25	1.25
With current derating	kHz	7.5	7.5	7.5
Power loss, max. ⁶⁾
At 50 Hz 400 V	kW	5.84	6.68	7.15
At 60 Hz 460 V	kW	6.3	7.3	7.8
Cooling air requirement	m³/s (ft³/s)	0.78 (27.5)	0.78 (27.5)	0.78 (27.5)
Sound pressure level L_pA (1 m) at 50/60 Hz	dB	70/73	70/73	70/73
DC link connection DCP, DCN		4 ? hole for M10 Busbar	4 ? hole for M10 Busbar	4 ? hole for M10 Busbar
Connection for Braking Module DCPA, DCNA⁷⁾		Connection for connection clip	Connection for connection clip	Connection for connection clip
Connection for dv/dt filter DCPS, DCNS		M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	1 ? 185	1 ? 185	1 ? 185
Motor connection U2, V2, W2		2 ? M12 screw	2 ? M12 screw	2 ? M12 screw
Conductor cross section, max. (IEC)	mm²	4 ? 240	4 ? 240	4 ? 240
Cable length, max. ⁸⁾
Shielded	m (ft)	300 (984)	300 (984)	300 (984)
Unshielded	m (ft)	450 (1476)	450 (1476)	450 (1476)
PE1/GND connection		M12 screw	M12 screw	M12 screw
Conductor cross section, max. (IEC)	mm²	240	240	240
PE2/GND connection		2 ? M12 screw	2 ? M12 screw	2 ? M12 screw
Conductor cross section, max. (IEC)	mm²	2 ? 240	2 ? 240	2 ? 240
Degree of protection		IP00	IP00	IP00
Dimensions
Width	mm (in)	503 (19.8)	503 (19.8)	503 (19.8)
Height	mm (in)	1475 (58.1)	1475 (58.1)	1475 (58.1)
Depth	mm (in)	547 (21.5)	547 (21.5)	547 (21.5)
Weight, approx.	kg (lb)	290 (639)	290 (639)	290 (639)
Frame size		HX	HX	HX

¹⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 400 V 3 AC 50 Hz.

²⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 460 V 3 AC 60 Hz.

³⁾ The base-load current I_L is based on a duty cycle of 110 % for 60 s or 150 % for 10 s with a duty cycle duration of 300 s.

⁴⁾ The base-load current I_H is based on a duty cycle of 150 % for 60 s or 160 % for 10 s with a duty cycle duration of 300 s.

⁵⁾ Information regarding the correlation between the pulse frequency and maximum output current/output frequency is provided in the SINAMICS Low Voltage Engineering Manual.

⁶⁾ The specified power loss represents the maximum value at 100% utilization. The value is lower under normal operating conditions.

⁷⁾ The connecting cables are included in the scope of supply of the Braking Module.

Line voltage 380 ... 480 V 3 AC DC link voltage 510 ... 720 V DC		Motor Modules
		6SL3320-1TE41-0AA3	6SL3320-1TE41-2AA3	6SL3320-1TE41-4AA3
Type rating
At I_L (50 Hz 400 V) ¹⁾	kW	560	710	800
At I_H (50 Hz 400 V) ¹⁾	kW	450	560	710
At I_L (60 Hz 460 V) ²⁾	hp	800	1000	1150
At I_H (60 Hz 460 V) ²⁾	hp	700	900	1000
Output current
Rated current I_{rated O}	A	985	1260	1405
Base-load current I_L³⁾	A	960	1230	1370
Base-load current I_H⁴⁾	A	860	1127	1257
Maximum current I_max A	A	1440	1845	2055
DC link current
Rated current I_rated DC when supplied via
Basic/Smart Line Module	A	1182	1512	1686
Active Line Module	A	1064	1361	1517
Base-load current I_L DC ³⁾ when supplied via
Basic/Smart Line Module	A	1152	1474	1643
Active Line Module	A	1037	1326	1479
Base-load current I_{H DC}⁴⁾ when supplied from
Basic/Smart Line Module	A	1051	1345	1500
Active Line Module	A	946	1211	1350
Current demand
24 V DC auxiliary power supply	A	1.25	1.4	1.4
400 V AC	A	5.4	5.4	5.4
DC link capacitance	?F	18900	26100	28800
Pulse frequency ⁵⁾
Rated pulse frequency	kHz	1.25	1.25	1.25
Pulse frequency, max.
Without current derating	kHz	1.25	1.25	1.25
With current derating	kHz	7.5	7.5	7.5
Power loss, max. ⁶⁾
At 50 Hz 400 V	kW	9.5	11.1	12.0
At 60 Hz 460 V	kW	10.2	12.0	13.0
Cooling air requirement	m³/s (ft³/s)	1.08 (38.1)	1.08 (38.1)	1.08 (38.1)
Sound pressure level L_pA (1 m) at 50/60 Hz	dB	71/73	71/73	71/73
DC link connection DCP, DCN		4 ? hole for M10 Busbar	4 ? hole for M10 Busbar	4 ? hole for M10 Busbar
Connection for Braking Module DCPA, DCNA⁷⁾		Connection for connection clip	Connection for connection clip	Connection for connection clip
Connection for dv/dt filter DCPS, DCNS		2 x M10 screw	2 x M10 screw	2 x M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 185	2 ? 185	2 ? 185
Motor connection U2, V2, W2		3 ? M12 screw	3 ? M12 screw	3 ? M12 screw
Conductor cross section, max. (IEC)	mm²	6 ? 240	6 ? 240	6 ? 240
Cable length, max. ⁸⁾
Shielded	m (ft)	300 (984)	300 (984)	300 (984)
Unshielded	m (ft)	450 (1476)	450 (1476)	450 (1476)
PE1/GND connection		M12 screw	M12 screw	M12 screw
Conductor cross section, max. (IEC)	mm²	240	240	240
PE2/GND connection		3 ? M12 screw	3 ? M12 screw	3 ? M12 screw
Conductor cross section, max. (IEC)	mm²	3 ? 240	3 ? 240	3 ? 240
Degree of protection		IP00	IP00	IP00
Dimensions
Width	mm (in)	704 (27.7)	704 (27.7)	704 (27.7)
Height	mm (in)	1475 (58.1)	1475 (58.1)	1475 (58.1)
Depth	mm (in)	549 (21.6)	549 (21.6)	549 (21.6)
Weight, approx.	kg (lb)	450 (992)	450 (992)	450 (992)
Frame size		JX	JX	JX

¹⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 400 V 3 AC 50 Hz.

²⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 460 V 3 AC 60 Hz.

³⁾ The base-load current I_L is based on a duty cycle of 110 % for 60 s or 150 % for 10 s with a duty cycle duration of 300 s.

⁴⁾ The base-load current I_H is based on a duty cycle of 150 % for 60 s or 160 % for 10 s with a duty cycle duration of 300 s.

⁵⁾Information regarding the correlation between the pulse frequency and maximum output current/output frequency is provided in the SINAMICS Low Voltage Engineering Manual.

⁶⁾ The specified power loss represents the maximum value at 100% utilization. The value is lower under normal operating conditions.

⁷⁾ The connecting cables are included in the scope of supply of the Braking Module.

Line voltage 500 ... 690 V 3 AC DC link voltage 675 ... 1035 V DC		Motor Modules
		6SL3320-1TG28-5AA3	6SL3320-1TG31-0AA3	6SL3320-1TG31-2AA3	6SL3320-1TG31-5AA3
Type rating
At I_L (50 Hz 690 V) ¹⁾	kW	75	90	110	132
At I_H (50 Hz 690 V) ¹⁾	kW	55	75	90	110
At I_L (50 Hz 500 V) ¹⁾	kW	55	55	75	90
At I_H (50 Hz 500 V) ¹⁾	kW	45	55	75	90
At I_L (60 Hz 575 V) ²⁾	hp	75	75	100	150
At I_H (60 Hz 575 V) ²⁾	hp	75	75	100	125
Output current
Rated current I_{rated O}	A	85	100	120	150
Base-load current I_L³⁾	A	80	95	115	142
Base-load current I_H⁴⁾	A	76	89	107	134
Maximum current I_max A	A	120	142	172	213
DC link current
Rated current I_rated DC when supplied via
Basic/Smart Line Module	A	102	120	144	180
Active Line Module	A	92	108	130	162
Base-load current I_L DC ³⁾ when supplied via
Basic/Smart Line Module	A	99	117	140	175
Active Line Module	A	89	105	126	157
Base-load current I_{H DC}⁴⁾ when supplied via
Basic/Smart Line Module	A	90	106	128	160
Active Line Module	A	81	96	115	144
Current demand
24 V DC auxiliary power supply	A	0.8	0.8	0.8	0.8
500 V AC	A	0.7	0.7	0.7	0.7
690 V AC	A	0.4	0.4	0.4	0.4
DC link capacitance	?F	1200	1200	1600	2800
Pulse frequency ⁵⁾
Rated frequency	kHz	1.25	1.25	1.25	1.25
Pulse frequency, max.
Without current derating	kHz	1.25	1.25	1.25	1.25
With current derating	kHz	7.5	7.5	7.5	7.5
Power loss, max. ⁶⁾
At 50 Hz 690 V	kW	1.17	1.43	1.89	1.8
At 60 Hz 575 V	kW	1.1	1.3	1.77	1.62
Cooling air requirement	m³/s (ft³/s)	0.17 (6.00)	0.17 (6.00)	0.17 (6.00)	0.17 (6.00)
Sound pressure level L_pA (1 m) at 50/60 Hz	dB	64/67	64/67	64/67	64/67
DC link connection DCP, DCN		M10 screw	M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 185	2 ? 185	2 ? 185	2 ? 185
Connection for Braking Module DCPA, DCNA⁷⁾		M6 stud	M6 stud	M6 stud	M6 stud
Connection for dv/dt filter DCPS, DCNS		M8 screw	M8 screw	M8 screw	M8 screw
Conductor cross section, max. (IEC)	mm²	1 ? 70	1 ? 70	1 ? 70	1 ? 70
Motor connection U2, V2, W2		M10 screw	M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 185	2 ? 185	2 ? 185	2 ? 185
Cable length, max. ⁸⁾
Shielded	m (ft)	300 (984)	300 (984)	300 (984)	300 (984)
Unshielded	m (ft)	450 (1476)	450 (1476)	450 (1476)	450 (1476)
PE1/GND connection		M10 screw	M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 185	2 ? 185	2 ? 185	2 ? 185
PE2/GND connection		M10 screw	M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 185	2 ? 185	2 ? 185	2 ? 185
Degree of protection		IP20	IP20	IP20	IP20
Dimensions
Width	mm (in)	326 (12.8)	326 (12.8)	326 (12.8)	326 (12.8)
Height	mm (in)	1400 (55.1)	1400 (55.1)	1400 (55.1)	1400 (55.1)
Depth	mm (in)	356 (14.0)	356 (14.0)	356 (14.0)	356 (14.0)
Weight, approx.	kg (lb)	95 (209)	95 (209)	95 (209)	95 (209)
Frame size		FX	FX	FX	FX

¹⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 500 V or 690 V 3 AC 50 Hz.

²⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 575 V 3 AC 60 Hz.

³⁾ The base-load current I_L is based on a duty cycle of 110 % for 60 s or 150 % for 10 s with a duty cycle duration of 300 s.

⁴⁾ The base-load current I_H is based on a duty cycle of 150 % for 60 s or 160 % for 10 s with a duty cycle duration of 300 s.

⁵⁾ Information regarding the correlation between the pulse frequency and maximum output current/output frequency is provided in the SINAMICS Low Voltage Engineering Manual.

⁶⁾ The specified power loss represents the maximum value at 100% utilization. The value is lower under normal operating conditions.

⁷⁾ The connecting cables are included in the scope of supply of the Braking Module.

Line voltage 500 ... 690 V 3 AC DC link voltage 675 ... 1035 V DC		Motor Modules
		6SL3320-1TG31-8AA3	6SL3320-1TG32-2AA3	6SL3320-1TG32-6AA3	6SL3320-1TG33-3AA3
Type rating
At I_L (50 Hz 690 V) ¹⁾	kW	160	200	250	315
At I_H (50 Hz 690 V) ¹⁾	kW	132	160	200	250
At I_L (50 Hz 500 V) ¹⁾	kW	110	132	160	200
At I_H (50 Hz 500 V) ¹⁾	kW	90	110	132	160
At I_L (60 Hz 575 V) ²⁾	hp	150	200	250	300
At I_H (60 Hz 575 V) ²⁾	hp	150	200	200	250
Output current
Rated current I_{rated O}	A	175	215	260	330
Base-load current I_L³⁾	A	171	208	250	320
Base-load current I_H⁴⁾	A	157	192	233	280
Maximum current I_max A	A	255	312	375	480
DC link current
Rated current I_rated DC when supplied via
Basic/Smart Line Module	A	210	258	312	396
Active Line Module	A	189	232	281	356
Base-load current I_L DC ³⁾ when supplied via
Basic/Smart Line Module	A	204	251	304	386
Active Line Module	A	184	226	273	347
Base-load current I_{H DC}⁴⁾ when supplied via
Basic/Smart Line Module	A	186	229	277	352
Active Line Module	A	168	206	250	316
Current demand
24 V DC auxiliary power supply	A	0.9	0.9	0.9	0.9
500 V AC	A	1.5	1.5	1.5	1.5
690 V AC	A	1.0	1.0	1.0	1.0
DC link capacitance	?F	2800	2800	3900	4200
Pulse frequency ⁵⁾
Rated frequency	kHz	1.25	1.25	1.25	1.25
Pulse frequency, max.
Without current derating	kHz	1.25	1.25	1.25	1.25
With current derating	kHz	7.5	7.5	7.5	7.5
Power loss, max. ⁶⁾
At 50 Hz 690 V	kW	2.67	3.09	3.62	4.34
At 60 Hz 575 V	kW	2.5	2.91	3.38	3.98
Cooling air requirement	m³/s (ft³/s)	0.36 (12.7)	0.36 (12.7)	0.36 (12.7)	0.36 (12.7)
Sound pressure level L_pA (1 m) at 50/60 Hz	dB	69/73	69/73	69/73	69/73
DC link connection DCP, DCN		M10 screw	M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 240	2 ? 240	2 ? 240	2 ? 240
Connection for Braking Module DCPA, DCNA⁷⁾		M6 stud	M6 stud	M6 stud	M6 stud
Connection for dv/dt filter DCPS, DCNS		M8 screw	M8 screw	M8 screw	M8 screw
Conductor cross section, max. (IEC)	mm²	1 ? 70	1 ? 70	1 ? 70	1 ? 70
Motor connection U2, V2, W2		M10 screw	M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 240	2 ? 240	2 ? 240	2 ? 240
Cable length, max. ⁸⁾
Shielded	m (ft)	300 (984)	300 (984)	300 (984)	300 (984)
Unshielded	m (ft)	450 (1476)	450 (1476)	450 (1476)	450 (1476)
PE1/GND connection		M10 screw	M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 240	2 ? 240	2 ? 240	2 ? 240
PE2/GND connection		M10 screw	M10 screw	M10 screw	M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 240	2 ? 240	2 ? 240	2 ? 240
Degree of protection		IP20	IP20	IP20	IP20
Dimensions
Width	mm (in)	326 (12.8)	326 (12.8)	326 (12.8)	326 (12.8)
Height	mm (in)	1533 (60.3)	1533 (60.3)	1533 (60.3)	1533 (60.3)
Depth	mm (in)	545 (21.4)	545 (21.4)	545 (21.4)	545 (21.4)
Weight, approx.	kg (lb)	136 (300)	136 (300)	136 (300)	136 (300)
Frame size		GX	GX	GX	GX

¹⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 500 V or 690 V 3 AC 50 Hz.

²⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 575 V 3 AC 60 Hz.

³⁾ The base-load current I_L is based on a duty cycle of 110 % for 60 s or 150 % for 10 s with a duty cycle duration of 300 s.

⁴⁾ The base-load current I_H is based on a duty cycle of 150 % for 60 s or 160 % for 10 s with a duty cycle duration of 300 s.

⁵⁾ Information regarding the correlation between the pulse frequency and maximum output current/output frequency is provided in the SINAMICS Low Voltage Engineering Manual.

⁶⁾ The specified power loss represents the maximum value at 100% utilization. The value is lower under normal operating conditions.

⁷⁾ The connecting cables are included in the scope of supply of the Braking Module.

Line voltage 500 ... 690 V 3 AC DC link voltage 675 ... 1035 V DC		Motor Modules
		6SL3320-1TG34-1AA3	6SL3320-1TG34-7AA3	6SL3320-1TG35-8AA3	6SL3320-1TG37-4AA3
Type rating
At I_L (50 Hz 690 V) ¹⁾	kW	400	450	560	710
At I_H (50 Hz 690 V) ¹⁾	kW	315	400	450	630
At I_L (50 Hz 500 V) ¹⁾	kW	250	315	400	500
At I_H (50 Hz 500 V) ¹⁾	kW	200	250	315	450
At I_L (60 Hz 575 V) ²⁾	hp	400	450	600	700
At I_H (60 Hz 575 V) ²⁾	hp	350	450	500	700
Output current
Rated current I_{rated O}	A	410	465	575	735
Base-load current I_L³⁾	A	400	452	560	710
Base-load current I_H⁴⁾	A	367	416	514	657
Maximum current I_max A	A	600	678	840	1065
DC link current
Rated current I_rated DC when supplied via
Basic/Smart Line Module	A	492	558	690	882
Active Line Module	A	443	502	621	794
Base-load current I_L DC ³⁾ when supplied via
Basic/Smart Line Module	A	479	544	672	859
Active Line Module	A	431	489	605	774
Base-load current I_{H DC}⁴⁾ when supplied via
Basic/Smart Line Module	A	437	496	614	784
Active Line Module	A	394	446	552	706
Current demand
24 V DC auxiliary power supply	A	1.0	1.0	1.0	1.25
500 V AC	A	3.0	3.0	3.0	4.4
690 V AC	A	2.1	2.1	2.1	3.1
DC link capacitance	?F	7400	7400	7400	11100
Pulse frequency ⁵⁾
Rated frequency	kHz	1.25	1.25	1.25	1.25
Pulse frequency, max.
Without current derating	kHz	1.25	1.25	1.25	1.25
With current derating	kHz	7.5	7.5	7.5	7.5
Power loss, max. ⁶⁾
At 50 Hz 690 V	kW	6.13	6.80	10.3	10.9
At 60 Hz 575 V	kW	5.71	6.32	9.7	10
Cooling air requirement	m³/s (ft³/s)	0.78 (27.5)	0.78 (27.5)	0.78 (27.5)	1.08 (38.1)
Sound pressure level L_pA (1 m) at 50/60 Hz	dB	70/73	70/73	70/73	71/73
DC link connection DCP, DCN		4 ? hole for M10 Busbar	4 ? hole for M10 Busbar	4 ? hole for M10 Busbar	4 ? hole for M10 Busbar
Connection for Braking Module DCPA, DCNA⁷⁾		M8 stud	M8 stud	M8 stud	M8 stud
Connection for dv/dt filter DCPS, DCNS		M10 screw	M10 screw	M10 screw	2 x M10 screw
Conductor cross section, max. (IEC)	mm²	1 ? 185	1 ? 185	1 ? 185	2 ? 185
Motor connection U2, V2, W2		2 ? M12 screw	2 ? M12 screw	2 ? M12 screw	3 ? M12 screw
Conductor cross section, max. (IEC)	mm²	4 ? 240	4 ? 240	4 ? 240	6 ? 240
Cable length, max. ⁸⁾
Shielded	m (ft)	300 (984)	300 (984)	300 (984)	300 (984)
Unshielded	m (ft)	450 (1476)	450 (1476)	450 (1476)	450 (1476)
PE1/GND connection		M12 screw	M12 screw	M12 screw	M12 screw
Conductor cross section, max. (IEC)	mm²	240	240	240	240
PE2/GND connection		2 ? M12 screw	2 ? M12 screw	2 ? M12 screw	3 ? M12 screw
Conductor cross section, max. (IEC)	mm²	2 ? 240	2 ? 240	2 ? 240	3 ? 240
Degree of protection		IP00	IP00	IP00	IP00
Dimensions
Width	mm (in)	503 (19.8)	503 (19.8)	503 (19.8)	704 (27.7)
Height	mm (in)	1475 (58.1)	1475 (58.1)	1475 (58.1)	1475 (58.1)
Depth	mm (in)	547 (21.5)	547 (21.5)	547 (21.5)	550 (21.6)
Weight, approx.	kg (lb)	290 (639)	290 (639)	290 (639)	450 (992)
Frame size		HX	HX	HX	JX

¹⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 500 V or 690 V 3 AC 50 Hz.

²⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 575 V 3 AC 60 Hz.

³⁾ The base-load current I_L is based on a duty cycle of 110 % for 60 s or 150 % for 10 s with a duty cycle duration of 300 s.

⁴⁾ The base-load current I_H is based on a duty cycle of 150 % for 60 s or 160 % for 10 s with a duty cycle duration of 300 s.

⁵⁾ Information regarding the correlation between the pulse frequency and maximum output current/output frequency is provided in the SINAMICS Low Voltage Engineering Manual.

⁶⁾ The specified power loss represents the maximum value at 100% utilization. The value is lower under normal operating conditions.

⁷⁾ The connecting cables are included in the scope of supply of the Braking Module.

Line voltage 500 ... 690 V 3 AC DC link voltage 675 ... 1035 V DC		Motor Modules
		6SL3320-1TG38-1AA3	6SL3320-1TG38-8AA3	6SL3320-1TG41-0AA3	6SL3320-1TG41-3AA3
Type rating
At I_L (50 Hz 690 V) ¹⁾	kW	800	900	1000	1200
At I_H (50 Hz 690 V) ¹⁾	kW	710	800	900	1000
At I_L (50 Hz 500 V) ¹⁾	kW	560	630	710	900
At I_H (50 Hz 500 V) ¹⁾	kW	500	560	630	800
At I_L (60 Hz 575 V) ²⁾	hp	800	900	1000	1250
At I_H (60 Hz 575 V) ²⁾	hp	700	800	900	1000
Output current
Rated current I_{rated O}	A	810	910	1025	1270
Base-load current I_L³⁾	A	790	880	1000	1230
Base-load current I_H⁴⁾	A	724	814	917	1136
Maximum current I_max A	A	1185	1320	1500	1845
DC link current
Rated current I_rated DC when supplied via
Basic/Smart Line Module	A	972	1092	1230	1524
Active Line Module	A	875	983	1107	1372
Base-load current I_L DC ³⁾ when supplied via
Basic/Smart Line Module	A	947	1064	1199	1485
Active Line Module	A	853	958	1079	1337
Base-load current I_{H DC}⁴⁾ when supplied via
Basic/Smart Line Module	A	865	971	1094	1356
Active Line Module	A	778	874	985	1221
Current demand
24 V DC auxiliary power supply	A	1.25	1.4	1.4	1.4
500 V AC	A	4.4	4.4	4.4	4.4
690 V AC	A	3.1	3.1	3.1	3.1
DC link capacitance	?F	11100	14400	14400	19200
Pulse frequency ⁵⁾
Rated frequency	kHz	1.25	1.25	1.25	1.25
Pulse frequency, max.
Without current derating	kHz	1.25	1.25	1.25	1.25
With current derating	kHz	7.5	7.5	7.5	7.5
Power loss, max. ⁶⁾
At 50 Hz 690 V	kW	11.5	11.7	13.2	16.0
At 60 Hz 575 V	kW	10.5	10.6	12.0	14.2
Cooling air requirement	m³/s (ft³/s)	1.08 (38.1)	1.08 (38.1)	1.08 (38.1)	1.08 (38.1)
Sound pressure level L_pA (1 m) at 50/60 Hz	dB	71/73	71/73	71/73	71/73
DC link connection DCP, DCN		4 ? hole for M10 Busbar	4 ? hole for M10 Busbar	4 ? hole for M10 Busbar	4 ? hole for M10 Busbar
Connection for Braking Module DCPA, DCNA⁷⁾		M8 stud	M8 stud	M8 stud	M8 stud
Connection for dv/dt filter DCPS, DCNS		2 x M10 screw	2 x M10 screw	2 x M10 screw	2 x M10 screw
Conductor cross section, max. (IEC)	mm²	2 ? 185	2 ? 185	2 ? 185	2 ? 185
Motor connection U2, V2, W2		3 ? M12 screw	3 ? M12 screw	3 ? M12 screw	3 ? M12 screw
Conductor cross section, max. (IEC)	mm²	6 ? 240	6 ? 240	6 ? 240	6 ? 240
Cable length, max. ⁸⁾
Shielded	m (ft)	300 (984)	300 (984)	300 (984)	300 (984)
Unshielded	m (ft)	450 (1476)	450 (1476)	450 (1476)	450 (1476)
PE1/GND connection		M12 screw	M12 screw	M12 screw	M12 screw
Conductor cross section, max. (IEC)	mm²	240	240	240	240
PE2/GND connection		3 ? M12 screw	3 ? M12 screw	3 ? M12 screw	3 ? M12 screw
Conductor cross section, max. (IEC)	mm²	3 ? 240	3 ? 240	3 ? 240	3 ? 240
Degree of protection		IP00	IP00	IP00	IP00
Dimensions
Width	mm (in)	704 (27.7)	704 (27.7)	704 (27.7)	704 (27.7)
Height	mm (in)	1475 (58.1)	1475 (58.1)	1475 (58.1)	1475 (58.1)
Depth	mm (in)	550 (21.6)	550 (21.6)	550 (21.6)	550 (21.6)
Weight, approx.	kg (lb)	450 (992)	450 (992)	450 (992)	450 (992)
Frame size		JX	JX	JX	JX

¹⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 500 V or 690 V 3 AC 50 Hz.

²⁾ Rated output of a typical 6-pole standard induction motor based on I_L or I_H for 575 V 3 AC 60 Hz.

³⁾ The base-load current I_L is based on a duty cycle of 110 % for 60 s or 150 % for 10 s with a duty cycle duration of 300 s.

⁴⁾ The base-load current I_H is based on a duty cycle of 150 % for 60 s or 160 % for 10 s with a duty cycle duration of 300 s.

⁵⁾ Information regarding the correlation between the pulse frequency and maximum output current/output frequency is provided in the SINAMICS Low Voltage Engineering Manual.

⁶⁾ The specified power loss represents the maximum value at 100% utilization. The value is lower under normal operating conditions.

⁷⁾ The connecting cables are included in the scope of supply of the Braking Module.

skener.ru

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
Бесконтактные выключатели Конечные выключатели Оптические датчики Энкодеры

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FS - Установка умягчения

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FK - Установка обезжелезивания