SINAMICS S120 Cabinet Modules . Технические данные. Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SINAMICS S120 Cabinet Modules

| | | | | | |

SINAMICS S120 Cabinet Modules

The most important directives and standards are listed below. These are used as basis for the SINAMICS S120 Cabinet Modules drive system and they must be carefully observed to achieve an EMC-compliant configuration that is safe both functionally and in operation.

European directives
2006/95/EC	Low-voltage directive: Legal guidelines of the EU member states concerning electrical equipment for use within specified voltage limits
2004/108/EC	EMC directive: Legal guidelines of the EU member states for electromagnetic compatibility
European standards
EN 954?1 ¹⁾	Safety of machinery – safety-related parts of control systems; Part 1: General design principles
EN ISO 13849?1	Safety of machinery – safety-related parts of control systems; Part 1: General design guidelines (ISO 13849-1: 2006) (replaces EN 954-1)
EN 60146?1?1	Semiconductor converters – General requirements and line-commutated converters Part 1-1: Specification of basic requirements
EN 60204?1	Safety of machinery – Electrical equipment of machines; Part 1: General requirements
EN 60529	Degrees of protection provided by enclosures (IP code)
EN 61508?1	Functional safety of electrical/electronic/programmable electronic safety-related systems Part 1: General requirements
EN 61800?2	Variable-speed electric drives Part 2: General requirements – Rating specifications for low-voltage adjustable frequency AC power drive systems
EN 61800?3	Variable-speed electric drives Part 3: EMC requirements including specific test methods
EN 61800?5?1	Adjustable-speed electrical power drive systems Part 5: Safety requirements Main section 1: Electrical and thermal requirements
EN 61800?5?2	Adjustable speed electrical power drive systems Part 5-2: Safety requirements – Functional safety (IEC 61800-5-2:) 2007)

¹⁾ Will be replaced by EN ISO 13849-1 at the end of 2011.

General technical specifications

Electrical specifications
Line voltages	380 … 480 V 3 AC, ±10 % (-15 % < 1 min) 500 … 690 V 3 AC, ±10 % (-15 % < 1 min)
Line supply types	Grounded TN/TT systems and non-grounded IT systems
Line frequency	47 … 63 Hz
Output frequency ¹⁾
Control type Servo	0 … 650 Hz
Control type Vector	0 … 600 Hz
Control type V/f	0 … 600 Hz
Line power factor Fundamental
Basic Line Module	> 0.96
Smart Line Module	> 0.96
Active Line Module	Adjustable (factory-set to cos ? = 1)
Efficiency
Basic Line Module	> 99.0 %
Smart Line Module	> 98.5 %
Active Line Module	> 97.5 % (including Active Interface Module)
Motor Module	> 98.5 %
Overvoltage category	III to EN 61800?5?1
Control method	Vector/servo control with and without encoder or V/f control
Fixed speeds	15 fixed speeds plus 1 minimum speed, parameterizable (in the default setting, 3 fixed setpoints plus 1 minimum speed are selectable using terminal block/PROFIBUS/PROFINET)
Skipped speed ranges	4, parameterizable
Setpoint resolution	0.001 rpm digital (14 bit + sign) 12 bit analog
Braking operation	With Active Line Modules and Smart Line Modules, four-quadrant operation as standard (energy recovery). With Basic Line Modules, single-quadrant operation as standard. Braking when the power fails using an optional braking module.
Mechanical specifications
Degree of protection	IP20 (higher degrees of protection up to IP54 optional)
Protection class	I acc. to EN 61800?5?1
Touch protection	EN 50274/BGV A3 for the intended purpose
Cabinet system	Rittal TS 8, doors with double-barb lock, three-section base plates for cable entry
Paint finish	RAL 7035 (indoor requirements)
Type of cooling	Forced air cooling AF to EN 60146
Ambient conditions	Storage ²⁾	Transport ²⁾		Operation
Ambient temperature	-25 ... +55 °C	-25 ... +70 °C from -40 °C³⁾ for 24 hours		0 ... +40 °C to +50 °C, see derating data
Relative humidity (condensation not permissible)	5 ... 95 % ³⁾ Class 1K4 acc. to IEC 60721?3?1	5 ... 95 % at 40 °C Class 2K3 acc. to IEC 60721?3?2		5 ... 95 % ³⁾ Class 3K3 acc. to IEC 60721?3?3
Environmental class/harmful chemical substances	Class 1C2 acc. to EN 60721?3?1	Class 2C2 acc. to EN 60721?3?2		Class 3C2 acc. to EN 60721?3?3
Organic/biological influences	Class 1B1 acc. to EN 60721?3?1	Class 2B1 acc. to EN 60721?3?2		Class 3B1 acc. to EN 60721?3?3
Degree of pollution	2 acc. to EN 61800?5?1	2 acc. to EN 61800?5?1		2 acc. to EN 61800?5?1
Installation altitude	Cabinet Modules, chassis format: up to 2000 m above sea level, without derating, > 2000 m, see characteristic curves/derating data For Motor Modules Booksize Cabinet Kit format as well as Central Braking Modules: up to 1000 m above sea level without derating, > 1000 m, see characteristic curves/derating data
Mechanical stability	Storage ²⁾	Transport ²⁾		Operation
Vibration load	Class 1M1 acc. to EN 60721?3?1	Class 2M1 acc. to EN 60721?3?2		–
Deflection	1.5 mm at 5 ... 9 Hz	3.1 mm at 5 ... 9 Hz		0.075 mm at 10 ... 58 Hz
Acceleration	5 m/s? at > 9 ... 200 Hz	10 m/s? at > 9 ... 200 Hz		9.8 m/s? at > 58 ... 200 Hz
Shock load	Class 1M1 acc. to EN 60721?3?1		Class 2M1 acc. to EN 60721?3?2	Class 3M1 acc. to EN 60721?3?3
Acceleration	40 m/s? at 22 ms	100 m/s? at 11 ms		100 m/s? at 11 ms
Compliance with standards
Conformances/approvals, according to	CE (EMC Directive No. 2004/108/EC and Low-Voltage Directive No. 2006/95/EC)
Radio interference suppression	SINAMICS drive converter systems are not designed for connection to the public network (first environment). Radio interference suppression is compliant with the EMC product standard for variable-speed drives EN 61800-3, "Second environment" (industrial line supplies). The equipment can cause electromagnetic interference when it is connected to the public network. However, if supplementary measures are taken (e.g. > line filter), it can also be operated in the "first environment".

¹⁾ Please note:
- The correlation between the maximum output frequency, pulse frequency and current derating. Higher output frequencies for specific configurations are available on request.

- The correlation between the minimum output frequency and permissible output current (current derating).
Information is provided in the SINAMICS Low Voltage Engineering Manual.

²⁾ In transport packaging.

³⁾ Deviations with respect to the specified class are underlined.