The electromagnetic double‑disc spring‑set brake KFB, see picture "KFB spring‑set brake with manual lever", is intended to operate solely as a holding brake for this application. With the exception of emergency braking, it may only be operated as a dynamically loaded operational brake if it is appropriately dimensioned or after consultation with the manufacturer. It is a spring‑loaded, electrically operated, double‑disc brake, which operates when the power is switched off. When the coil (2) is energized with a DC voltage, the brake is released electromagnetically. If the coil (2) is de‑energized, the springs (6) press the armature plate (4) axially against the friction‑lining carrier (5) which in turn presses against the brake flange (7); this sequence provides the braking action. The brake is released when the coil (2) is energized. The magnetic field attracts the armature plate (4) towards the coil form (1), counteracting the spring pressure on the coil form. The air gap can be adjusted within a wide range, ensuring high availability of the brake. The motor and brake are coupled by means of a flange (12). Emergency brake release is possible by means of 2 emergency release screws – optionally with hand lever release.

As a result of the compact design with the enclosed coil form housing and appropriate sealing from the shaft, the brake has degree of protection IP67 when the housing is closed.

All the brake connections such as coil, microswitch, etc. are taken to the motor terminal box.

KFB spring‑set brake with manual lever

Protective element

The brakes should be connected at the DC end, i.e. between the rectifier and coil (see circuit diagram below). This ensures a significantly shorter closing time than if the brake were connected at the AC end. A protective element (varistor + spark quenching) must be fitted in parallel to each brake coil. This protects the brake coil against excessively high de‑energization voltages on the one hand, and the contactor contacts on the other. These protective elements must be installed close to the brake coils where possible, e.g. in the motor terminal box or in a distribution board on the subframes in the case of traversing gear. Protective elements PE‑400/150/5 are directly available from the manufacturer¹⁾ under Article No. 008099300249.

Technical specifications

Special versions

Emergency release with hand lever, option J25

In addition to brake release at zero current via 2 emergency release screws, it is also possible to release the brake by means of a hand lever permanently mounted on the brake housing. The lever is lockable.

Microswitch for "brake released" monitoring, option J26

The brake can be fitted with a microswitch for monitoring the "brake released" state. The contact is rated for:

• < 30 V DC, 5.0 A
• < 125 V DC, 0.5 A
• < 250 V AC, 5.0 A

Microswitch for air gap monitoring/wear, option J24

A 2nd microswitch can be fitted to monitor the "maximum air gap" function. Tripping of this contact indicates that full braking power is no longer available and the air gap must be adjusted immediately. The contact load rating is identical to that of the "brake released" microswitch.

Standstill heater, option J27

The installation of a heater can prevent the formation of condensate, e.g. caused by fluctuations in temperature and air humidity, inside the brake. This heater must not be switched on when the motor is operating. The heater is designed for a supply voltage of 230 V AC and a heat output of 40 W.

Encoder mounting, option J28/J29

An encoder (e.g. POG 10) can be mounted on the brake. Additional mounting components and other measures are required on the brake to fit an encoder.

Tacho socket T2 with coupling and mounting components is ordered with option J28 (see section "Design").

If an encoder is to be fitted at a later date, the brake can be supplied prepared for encoder mounting. This is possible with option J29. Option J29 does not include the coupling and mounting components.

It is also possible to retrofit an encoder by replacing the brake housing (the parts required, such as new housing, coupling, etc., can be ordered directly from the manufacturer¹⁾) using the brake serial number as a reference).

Brake control unit BCU

A brake control unit (BCU) can also be used to supply and monitor the brake on single drives. For technical specifications, price, etc., please contact the manufacturer¹⁾ directly.

Rectifier in terminal box, option C07/C01

The brake motors can also be supplied with a bridge rectifier installed.

Note:

It must, however, be noted that the closing time for the brake can be a factor of 10 longer than the values specified in the tables (see section "Technical specifications" below) because it is connected at the AC current side.

Three‑phase asynchronous motors 1LP4, 1LP6, 60 Hz variant​

The motor types 1LP4 and 1LP6 are also available in a 60 Hz variant.

The following must be stated in addition to the Article No.:

• 400 VО” 1LP....-...9. L5K
• 460 VО” 1LP....-...9. L5L
• 500 VО” 1LP....-...9. L5M

Technical specifications on request.

¹⁾
PINTSCH BUBENZER GmbH
Werk Dinslaken
HГјnxer Str. 149
D‑46537 Dinslaken
Phone +49 (0) 2064 / 602‑0
Fax +49 (0) 2064 / 602-515

http://www.pintschbubenzer.de

Email: info@pintschbubenzer.de