SIPLUS extreme RAIL analog inputs . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS extreme RAIL analog inputs

| | | | | |

SIPLUS extreme RAIL analog input modules

Article number		6AG2134-6GD00-4BA1
		SIPLUS ET 200SP AI 4XI 2-/4-WIRE TX RAIL
General information
Product type designation		AI 4xI 2-/4-wire ST
Product function
? I&M data		Yes; I&M0 to I&M3
? Measuring range scalable		No
Operating mode
? Oversampling		No
? MSI		No
CiR – Configuration in RUN
Reparameterization possible in RUN		Yes
Calibration possible in RUN		No
Supply voltage
Type of supply voltage		DC
Rated value (DC)		24 V
Reverse polarity protection		Yes
Analog inputs
Number of analog inputs		4; > 60 °C max. 1x +/- 20 mA permissible
permissible input current for current input (destruction limit), max.		50 mA
Cycle time (all channels), min.		Sum of the basic conversion times and additional processing times (depending on the parameterization of the active channels)
Input ranges (rated values), currents
? 0 to 20 mA		Yes
? -20 mA to +20 mA		Yes
? 4 mA to 20 mA		Yes
Cable length
? shielded, max.		1 000 m
Analog value generation for the inputs
Integration and conversion time/resolution per channel
? Resolution with overrange (bit including sign), max.		16 bit
? Integration time, parameterizable		Yes
? Interference voltage suppression for interference frequency f1 in Hz		16.6 / 50 / 60 Hz
? Conversion time (per channel)		180 / 60 / 50 ms
Smoothing of measured values
? Number of smoothing levels		4; None; 4/8/16 times
? parameterizable		Yes
Encoder
Connection of signal encoders
? for voltage measurement		No
? for current measurement as 2-wire transducer		Yes
— Burden of 2-wire transmitter, max.		650 ?
? for current measurement as 4-wire transducer		Yes
Errors/accuracies
Basic error limit (operational limit at 25 °C)
? Current, relative to input range, (+/-)		0.3 %
Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency
? Series mode interference (peak value of interference < rated value of input range), min.		70 dB
? Common mode voltage, max.		10 V
? Common mode interference, min.		90 dB
Isochronous mode
Isochronous operation (application synchronized up to terminal)		No
Interrupts/diagnostics/status information
Diagnostics function		Yes
Alarms
? Diagnostic alarm		Yes
? Limit value alarm		No
Diagnostic messages
? Monitoring the supply voltage		Yes
? Wire-break		Yes; at 4 to 20 mA
? Short-circuit		Yes; 2-wire mode: Short-circuit of the encoder supply to ground or of an input to the encoder supply
? Group error		Yes
? Overflow/underflow		Yes
Diagnostics indication LED
? Monitoring of the supply voltage (PWR-LED)		Yes; Green LED
? Channel status display		Yes; Green LED
? for channel diagnostics		No
? for module diagnostics		Yes; Green/red LED
Potential separation
Potential separation channels
? between the channels and backplane bus		Yes
Isolation
Isolation tested with		707 V DC (type test) and according to EN 50155 (routine test)
Standards, approvals, certificates
Railway application
? EN 50121-3-2		Yes; EMC for rail vehicles
? EN 50121-4		Yes; EMC for signal and telecommunications systems
? EN 50124-1		Yes; Railway applications - overvoltage category OV2; pollution degree PD2; rated surge voltage UNi = 0.5 kV; UNm = 24 V DC
? EN 50125-1		Yes; Rail vehicles - see ambient conditions
? EN 50125-2		Yes; Stationary electrical equipment - see ambient conditions
? EN 50125-3		Yes; Signal and telecommunications systems - see ambient conditions; vibrations and shocks: Application point outside of tracks (1 m to 3 m away from track)
? EN 50155		Yes; Rail vehicles - temperature class Tx, horizontal mounting position, salt spray Class ST2
? EN 61373		Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B
? Fire protection acc. to EN 45545-2		Yes; Rail vehicles - verification on request
Ambient conditions
Ambient temperature during operation
? horizontal installation, min.		-40 °C; = Tmin
? horizontal installation, max.		70 °C; = Tmax; +85 °C for 10 min (Tx acc. to EN 50155)
Extended ambient conditions
? relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against biologically active substances/conformity with EN 60721-3-5		Yes; Class 5B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances/conformity with EN 60721-3-5		Yes; Class 5C3 (RH < 75%) including salt spray according to EN 50155 (ST2). The supplied plug covers must remain in place over the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances/conformity with EN 60721-3-5		Yes; Class 5S3 including sand and dust. The supplied plug covers must remain in place over the unused interfaces during operation!
Dimensions
Width		15 mm
Weights
Weight, approx.		31 g
Other
Note:		For use in railway applications, also observe the product information "SIPLUS extreme RAIL" A5E37661960A Online Support article 109736776

Article number		6AG2134-6PA00-4BD0
		SIPLUS ET 200SP AI ENERGY METER TX RAIL
General information
Product type designation		AI energy meter 400VAC ST
Product function
? Voltage measurement		Yes
? Voltage measurement with voltage transformers		No
? Current measurement		Yes
? Phase current measurement without current transformers		No
? Phase current measurement with current transformers		Yes
? Energy measurement		Yes
? Frequency measurement		Yes
? Power measurement		Yes
? Active power measurement		Yes
? Reactive power measurement		Yes
? I&M data		Yes; I&M0 to I&M3
? Isochronous mode		No
Operating mode
? cyclic measurement		Yes
? acyclic measurement		Yes
? Acyclic measured value access		Yes
? Fixed measured value sets		Yes
? Freely definable measured value sets		No
CiR – Configuration in RUN
Reparameterization possible in RUN		Yes
Calibration possible in RUN		No
Installation type/mounting
Mounting position		Horizontal
Supply voltage
Design of the power supply		Supply via voltage measurement channel L1
Type of supply voltage		100 - 240 V AC
permissible range, lower limit (AC)		90 V
permissible range, upper limit (AC)		264 V
Line frequency
? permissible range, lower limit		47 Hz
? permissible range, upper limit		63 Hz
Address area
Address space per module
? Address space per module, max.		44 byte; 32 byte input / 12 byte output
Analog inputs
Cycle time (all channels), typ.		50 ms; Time for consistent update of all measured and calculated values (cyclic und acyclic data)
Interrupts/diagnostics/status information
Alarms
? Diagnostic alarm		Yes
? Limit value alarm		No
? Hardware interrupt		No
Diagnostics indication LED
? Monitoring of the supply voltage (PWR-LED)		Yes
? Channel status display		Yes; Green LED
? for channel diagnostics		Yes; red Fn LED
? for module diagnostics		Yes; green/red DIAG LED
Integrated Functions
Measuring functions
? Measuring procedure for voltage measurement		TRMS
? Measuring procedure for current measurement		TRMS
? Type of measured value acquisition		seamless
? Curve shape of voltage		Sinusoidal or distorted
? Buffering of measured variables		No
? Parameter length		38 byte
? Bandwidth of measured value acquisition		2 kHz; Harmonics: 39 / 50 Hz, 32 / 60 Hz
Operating mode for measured value acquisition
— automatic detection of line frequency		No; Parameterizable
Measuring range
— Frequency measurement, min.		45 Hz
— Frequency measurement, max.		65 Hz
Measuring inputs for voltage
— Measurable line voltage between phase and neutral conductor		230 V
— Measurable line voltage between the line conductors		400 V
— Measurable line voltage between phase and neutral conductor, min.		90 V
— Measurable line voltage between phase and neutral conductor, max.		264 V
— Measurable line voltage between the line conductors, min.		155 V
— Measurable line voltage between the line conductors, max.		460 V
— Measurement category for voltage measurement in accordance with IEC 61010-2-030		CAT II; CAT III in case of guaranteed protection level of 1.5 kV
— Internal resistance line conductor and neutral conductor		3.4 M?
— Power consumption per phase		20 mW
— Impulse voltage resistance 1,2/50µs		1 kV
Measuring inputs for current
— measurable relative current (AC), min.		5 %; Relative to the secondary rated current; 1 A, 5 A
— measurable relative current (AC), max.		100 %; Relative to the secondary rated current; 1 A, 5 A
— Continuous current with AC, maximum permissible		5 A; at > +60 °C max. permissible current 1 A per phase
— Apparent power consumption per phase for measuring range 5 A		0.6 V·A
— Rated value short-time withstand current restricted to 1 s		100 A
— Input resistance measuring range 0 to 5 A		25 m?
— Zero point suppression		Parameterizable: 20 - 250 mA, default 50 mA
— Surge strength		10 A; for 1 minute
Accuracy class according to IEC 61557-12
— Measured variable voltage		0.5
— Measured variable current		0.5
— Measured variable apparent power		1
— Measured variable active power		1
— Measured variable reactive power		1
— Measured variable power factor		0.5
— Measured variable active energy		1
— Measured variable reactive energy		2
— Measured variable phase angle		±1 °; not covered by IEC 61557-12
— Measured variable frequency		0.05
Potential separation
Potential separation channels
? between the channels and backplane bus		Yes; 3 700V AC (type test) CAT III
Isolation
Isolation tested with		2 300 V AC for 1 minute (type test) and according to EN 50155 (routine test)
Standards, approvals, certificates
Railway application
? EN 50121-3-2		Yes; EMC for rail vehicles
? EN 50121-4		Yes; EMC for signal and telecommunications systems
? EN 50124-1		Yes; Railway applications - overvoltage category OV2; pollution degree PD2; rated surge voltage UNi = 0.5 kV; UNm = 24 V DC
? EN 50125-1		Yes; Rail vehicles - see ambient conditions
? EN 50125-2		Yes; Stationary electrical equipment - see ambient conditions
? EN 50125-3		Yes; Signal and telecommunications systems - see ambient conditions; vibrations and shocks: Application point outside of tracks (1 m to 3 m away from track)
? EN 50155		Yes; Rail vehicles - temperature class Tx, horizontal mounting position, salt spray Class ST2
? EN 61373		Yes; Rail vehicles - vibrations and shocks: Category 1 Class A/B
? Fire protection acc. to EN 45545-2		Yes; Rail vehicles - verification on request
Ambient conditions
Ambient temperature during operation
? horizontal installation, min.		-40 °C; = Tmin
? horizontal installation, max.		70 °C; = Tmax; +85 °C for 10 min (Tx acc. to EN 50155)
Extended ambient conditions
? relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against biologically active substances/conformity with EN 60721-3-5		Yes; Class 5B2 mold and fungal spores (excluding fauna). The supplied plug covers must remain in place over the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances/conformity with EN 60721-3-5		Yes; Class 5C3 (RH < 75%) including salt spray according to EN 50155 (ST2). The supplied plug covers must remain in place over the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances/conformity with EN 60721-3-5		Yes; Class 5S3 including sand and dust. The supplied plug covers must remain in place over the unused interfaces during operation!
Dimensions
Width		20 mm
Weights
Weight (without packaging)		45 g
Other
Note:		For use in railway applications, also observe the product information "SIPLUS extreme RAIL" A5E37661960A Online Support article 109736776
Data for selecting a current transformer
? Burden power current transformer x/1A, min.		As a function of cable length and cross section, see device manual
? Burden power current transformer x/5A, min.		As a function of cable length and cross section, see device manual

skener.ru

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
Бесконтактные выключатели Конечные выключатели Оптические датчики Энкодеры

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FS - Установка умягчения

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FK - Установка обезжелезивания