Standardline (for 1LA8 motors only)

Standardline version

B20

Motor protection

Motor protection with PTC thermistors with 6 embedded temperature sensors for alarm and tripping

A12

Motor temperature detection with embedded temperature sensor KTY 84-130

A23

Installation of 6 PT100 resistance thermometers in stator winding

A61

Installation of 6 PT100 resistance thermometers in stator winding, 3-wire circuit from auxiliary terminal box (Option M50 or M88)

A64

Installation of 2 PT100 screw-in resistance thermometers in basic circuit for rolling-contact bearings

A72

Installation of 2 PT100 screw-in resistance thermometers for rolling-contact bearings, in 3-wire circuit from auxiliary terminal box (Option M50 or M88)

A78

Installation of 2 PT100 double screw-in resistance thermometers in 3-wire circuit for rollingcontact bearings

A80

New!

6 x PT100 Smart transmitter –40 to +140 °C Rosemount

M62

Motor connection and connection box

Two-part plate on connection box

K06

Undrilled entry plate

L01

Connection box on RHS

K09

Connection box on LHS

K10

Cable entry in direction of NDE with rotation of the terminal box console through 180°

N81

New!

Cable entry in direction of DE with rotation of the terminal box console through 180°

N82

New!

Cable entry from the top

N83

New!

Rotation of the terminal box console through 180°

N84

New!

Connection box on NDE

N85

New!

Connection box on top (1XB1634 connection box)

K11

DIN 89280 cable gland, maximum configuration

K57

Rotation of the connection box through 90°, entry from DE

K83

Rotation of the connection box through 90°, entry from NDE

K84

Rotation of the connection box through 180°

K85

Larger connection box (1XB1621 connection box)

M58

PE connection without cable lug

Q00

New!

Larger connection box (1XB1631 connection box)

L00

Larger connection box (1XB9600 connection box)

M63

New!

Subsequently rotatable main connection box

J12

New!

6 cables protruding, 1.5 m long

L48

6 cables protruding, 3 m long

L49

Auxiliary connection box 1XB9016 (cast-iron)

M50

Auxiliary connection box 1XB9015 (stainless steel)

M51

Flange version A660 instead of standard version

M61

Auxiliary connection box 1XB3020

L97

Auxiliary connection box 1XB9014 (aluminum)

M88

Connection box on NDE

M64

Windings and insulation

Temperature class 155 (F), used acc. to 155 (F), with service factor (SF)

C11

Temperature class 155 (F), used acc. to 155 (F), with increased output

C12

Temperature class 155 (F), used acc. to 155 (F), with increased coolant temperature

C13

Temperature class 180 (H), utilized to 155 (F), with service factor (SF 1.1)

C14

Colors and paint finish

Standard finish in RAL 7030 stone gray

–

Standard finish in other colors

Y53 • and standard finish RAL ….

Special finish in RAL 7030 stone gray

K26

Special finish in other colors

Y54 • and special finish RAL ….

Unpainted (only cast-iron parts primed)

K23

Special technology

Mounting of brake (incl. the brake from Stromag)

H47

Mounting of the holding brake SFB 160, 1600 Nm, 230 V, Pintsch-Bubenzer

J48

New!

Mounting of the holding brake SFB 160 SH, 2100 Nm, 230 V, Pintsch-Bubenzer

J49

New!

Mounting of the holding brake SFB 160 H, 2500 Nm, 230 V, Pintsch-Bubenzer

J56

New!

Mounting of the holding brake SFB 250 SH, 3300 Nm, 230 V, Pintsch-Bubenzer

J57

New!

Mounting of the holding brake SFB 250 H, 4000 Nm, 230 V, Pintsch-Bubenzer

J58

New!

Mounting of the holding brake SFB 250 H, 4000 Nm, 400 V, Pintsch-Bubenzer

J59

New!

Mounting of the holding brake SFB 400 SH, 5200 Nm, 400 V, Pintsch-Bubenzer

J66

New!

Mounting of the holding brake SFB 400 H, 6300 Nm, 400 V, Pintsch-Bubenzer

J67

New!

Mounting of the holding brake SFB 630 SH, 8000 Nm, 400 V, Pintsch-Bubenzer

J68

New!

Mounting of the holding brake SFB 630 H, 10000 Nm, 400 V, Pintsch-Bubenzer

J69

New!

Prepared for mounting of the holding brake SFB for shaft height 315

J06

New!

Prepared for mounting of the holding brake SFB for shaft height 355

J07

New!

Prepared for mounting of the holding brake SFB for shaft height 400

J08

New!

Prepared for mounting of the holding brake SFB for shaft height 450

J09

New!

Mounting of LL 861 900 220 rotary pulse encoder

H70

Mounting of HOG 10 D 1024 I rotary pulse encoder

H73

Prepared for mounting of LL 861 900 220

H78

Prepared for mounting of HOG 10 D 1024 I

H80

Mounting of HOG10 DN 2048 incremental encoder

H83

New!

Mounting of HOG11 DN 2048 incremental encoder

H84

New!

Mounting of LL861 incremental encoder (2048 pulses)

H85

New!

Mounting of LL861 900 222 rotary pulse encoder with Advanced Diagnostic System

H16

New!

HOG 11 DN 1024 I rotary pulse encoder (16 mm) with special anti-corrosion protection

H88

New!

Mounting of HOG 10 DN 1024 I rotary pulse encoder + centrifugal switch, (speed .... rpm), terminal box protection against humidity

Y74 • and required speed .... rpm

New!

Mounting of HOG 10 DN 1024 I rotary pulse encoder + centrifugal switch, (speed .... rpm), terminal box protection against dust

Y76 • and required speed .... rpm

New!

Mounting of HOG 10 D 1024 l with terminal box/protection against dust

N05

New!

Mounting of HOG 10 DN 1024 l with terminal box/protection against dust (zero signal)

N06

New!

Mounting of HOG 10 DN 1024 l with terminal box/protection against humidity (zero signal)

N08

New!

Mounting a special type of rotary pulse encoder

Y70 • and encoder designation

Mechanical design and degrees of protection

Low-noise version for 2-pole motors with clockwise direction of rotation

K37

Low-noise version for 2-pole motors with counterclockwise direction of rotation

K38

IP65 degree of protection

K50

IP56 degree of protection (non-heavy-sea)

K52

Rust-resistant screws (externally)

M27

Coolant temperature and site altitude

Coolant temperature –50 to +40 °C

D02

New!

Coolant temperature –40 to +40 °C

D03

Coolant temperature –30 to +40 °C

D04

Coolant temperature 45 °C, derating 4 %

D11

Coolant temperature 50 °C, derating 8 %

D12

Coolant temperature 55 °C, derating 13 %

D13

Coolant temperature 60 °C, derating 18 %

D14

Designs in accordance with standards and specifications

Electrical according to NEMA MG1-12

D30

Design according to UL with "Recognition Mark

D31

China Energy Efficiency Label

D34

New!

Ex certification for Russia

D35

New!

Conformity statement in accordance with 94/9/EC (ATEX) of an independent body for Zone 2 motors (Ex nA)

D36

New!

IEC Ex certificate – only in combination with order codes M72 and M73

D37

New!

Canadian regulations (CSA)

D40

Pump drives for sea water desalination plants

Commissioning of the classification society by Siemens

E88

New!

Commissioning of the classification society by third party

E89

New!

Pump drive for sea water desalination plants certified according to Lloyd's Register

E90

New!

Design for Zones according to ATEX

Design for Zone 2 for mains-fed operation Ex nA II T3 according to IEC/EN 60079?15

M72

ADesign for Zone 2 for converter-fed operation, with derating Ex nA II T3 according to IEC/EN 60079?15

M73

Design for Zone 22 for non-conductive dust (IP55) for mains-fed operation

M35

Design for Zone 22 for non-conductive dust (IP55) for converter-fed operation, with derating

M39

VIK version

K30

Ex nA II on VIK rating plate

C27

Bearings and lubrication

Measuring nipple for SPM shock pulse measurement for bearing inspection

G50

Shock pulse measurement, fixed sensor and distributor box

H05

New!

Shock pulse measurement, complete alarm box

H07

New!

Automatic re-lubricating device EasyMatic

N30

New!

Automatic re-lubricating device STAR CONTROL TIME M120

N31

New!

Automatic re-lubricating device STAR CONTROL IMPULSE L250

N32

New!

Bearing design for increased cantilever forces

K20

Balance and vibration quantity

Vibration quantity level B

K02

Full-key balancing

L68

Shaft and rotor

Second standard shaft extension

K16

Shaft extension with standard dimensions, without feather keyway

K42

Non-standard cylindrical shaft extension

Y55 • and identification code

Heating and ventilation

Metal external fan

K35

Anti-condensation heating for 230 V

K45

Anti-condensation heating for 115 V

K46

Anti-condensation heating for 400 V

L08

New!

Anti-condensation heating for 500 V

L09

New!

Sheet metal fan cover

L36

Separately driven fan with non-standard voltage and/or frequency

Y81 • and identification code

Rating plate and extra rating plates

Second rating plate, loose

K31

Extra rating plate or rating plate with deviating rating plate data

Y80 • and identification code

Extra rating plate with identification codes

Y82 • and identification code

Extension of liability for defects

Extension of liability for defects by 12 to 24 months

Q80

New!

Extension of liability for defects by 18 to 30 months

Q81

New!

Extension of liability for defects by 24 to 36 months

Q82

New!

Extension of liability for defects by 30 to 42 months

Q83

New!

Extension of liability for defects by 36 to 48 months

Q84

New!

Extension of liability for defects by 48 to 60 months

Q85

New!

Packaging, safety notes, documentation and test certificates

Document – Electrical data sheet

B31

Document – Order dimension drawing

B32

Document – Standard test schedule

B34

New!

Document – Load characteristics

B37

Document – Production schedule: Generated once

B43

New!

Document – Production schedule: Updated every two weeks

B44

New!

Document – Production schedule: Updated monthly

B45

New!

Standard test (routine test) with acceptance

F01

Visual acceptance and report handover with acceptance

F03

Temperature-rise test, without acceptance

F04

Temperature-rise test with acceptance

F05

Noise measurement in no-load operation, no noise analysis, without acceptance

F28

Noise measurement in no-load operation, no noise analysis, with acceptance

F29

Noise measurement in no-load operation, with noise analysis, without acceptance

F62

Noise measurement in no-load operation, with noise analysis, with acceptance

F63

Recording of current and torque curves with torque metering shaft during starting, without acceptance

F34

Recording of current and torque curves with torque metering shaft during starting, with acceptance

F35

Measurement of locked-rotor torque and current, without acceptance

F52

Measurement of locked-rotor torque and current, with acceptance

F53

Type test with heat run for horizontal motors, without acceptance

F82

Type test with heat run for horizontal motors, with acceptance

F83

Type test with heat run for vertical motors, without acceptance

F92

Type test with heat run for vertical motors, with acceptance

F93