Liquid-cooled Power Modules in blocksize format. Технические данные. Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на Liquid-cooled Power Modules in blocksize format

| | | | |

Liquid-cooled Power Modules in blocksize format

Liquid-cooled PM340 Power Module in blocksize format 6SL3215-1SE...
Line connection voltage (up to 2000 m (6562 ft) above sea level)	380 ... 480 V 3 AC ±10 % (in operation -15 % < 1 min)
Line system configuration	Grounded TN/TT systems and non-grounded IT systems
Line frequency	47 … 63 Hz
Line power factor with a 3 AC line connection voltage and rated power
Fundamental power factor (cos ₁)	> 0,96
Total ()	0.65 … 0.95
Overvoltage category to EN 60664-1	Class III
Precharging frequency of the DC link	1 every 30 s
DC link voltage, approx.	1.35 x line voltage
Output frequency
Control type Servo	0 … 650 Hz¹⁾
Control type Vector	0 … 300 Hz¹⁾
Control typeV/f	0 … 600 Hz¹⁾
Electronics power supply	24 V DC -15 %/+20 %
Radio interference suppression
Standard	No radio interference suppression
Type of cooling	Liquid cooling with integrated heat exchanger in stainless-steel version
Coolant²⁾ pH value Chloride Sulfate Hardness Conductivity Colony number Max. size of entrained particles	6.0 … 9.0 < 200 mg/l < 240 mg/l < 2.5 mmol/l³⁾ < 2000 S/cm < 1000 col/ml⁴⁾ < 100 m
Cooling circuit²⁾
System pressure with reference to atmospheric pressure, max. Pressure drop at rated volumetric flow Recommended pressure range Inlet temperature of liquid coolant	600 kPa 70 kPa 80 … 200 kPa Dependent on the ambient temperature, condensation is not permitted 0 … 50 °C (32 … 122 °F) (temperature range between 0 °C and 5 °C (32 … 41 °F with anti-freeze only; recommended anti-freeze: Antifrogen N from Clariant)
Permissible ambient temperature (air) during operation	Dependent on the inlet temperature of the coolant, condensation is not permissible 0 … 40 °C (32 … 113 °F) without derating, > 40 … 55 °C (113 … 122 °F) see derating characteristics
Installation altitude	Up to 2000 m (3281 ft) above sea level without derating, > 2000 ... 4000 m (3281 ... 13124 ft) above sea level, see derating characteristics
Conformity	CE (Low-Voltage and EMC Directives)
Approvals, according to	cULus
Safety Integrated	Safety Integrity Level 2 (SIL 2) acc. to IEC 61508, Performance Level d (PLd) acc. to ISO 13849 1 and Control Category 3 acc. to ISO 13849 1 or EN 954 1. For further information see chapter "Safety Integrated"

¹⁾ Note the correlation between max. output frequency, pulse frequency and current derating.
For further information see chapter "System description – Dimensioning".

²⁾ The values are applicable to coolant (water) without the addition of anti-freeze or inhibitors. When anti-freeze or inhibitors are added, the specifications of the manufacturer regarding water quality must be observed. The proportion of anti-freeze must not exceed a minimum concentration, otherwise the coolant has a marked corrosive effect. In the case of Antifrogen N, the recommended range of the ratio of Antifrogen N to water lies between 20/80 and 45/55 Vol.%

³⁾ The hardness of the coolant, especially the concentration of calcium compounds should be kept to a minimum to prevent the build-up of damaging calcium deposits (lime scale). A hardness < 1.5 mmol/l is recommended.

⁴⁾ The number of microbes should generally be as low as possible to prevent damage as a result of slime-producing, iron-depositing, corroding bacteria. In closed coolant circuits, the accumulation of microbes can be prevented, for example, by adding anti-freeze. The concentration of anti-freeze must only reach a minimum level to prevent corrosion, see Footnote²⁾.

Line voltage 380 … 480 V 3 AC		Liquid-cooled Power Module in blocksize format
		6SL3215-1SE23 8UA0	6SL3215-1SE26 0UA0	6SL3215-1SE27 5UA0
Output current
Rated current I_rated	A	38	60	75
Base-load currentI_H	A	33	48	65
For S6 duty (40%)I_S6	A	49	78	98
I _max	A	64	90	124
Type rating¹⁾
Based onI_rated	kW (HP)	18.5 (25)	30 (40)	37 (50)
Based onI_H	kW (HP)	15 (20)	22 (30)	30 (50)
Rated pulse frequency	kHz	4	4	4
Power loss
Total, approx.	kW	0.38	0.69	0.99
Lost to ambient air, approx.	kW	0.09	0.13	0.16
Cooling circuit
Rated volumetric flow for water at 70 kPa pressure drop	dm³/min (l/min)	8	8	8
Cooling circuit connection, inlet and return		Pipe thread ISO 228 – G B (external thread ’’, flat-sealing)	Pipe thread ISO 228 – G B (external thread ’’, flat-sealing)	Pipe thread ISO 228 – G B (external thread ’’, flat-sealing)
Liquid volume of integrated heat exchanger	dm³ (l)	0.1	0.1	0.13
Sound pressure level L _pA (1 m) at 50/60 Hz	dB	< 60	< 60	< 60
Rated input current with/without line reactor	A	40/46	63/72	78/88
Resistance value of the external braking resistor		27	27	15
Cable length, max. to braking resistor	m (ft)	15 (49)	15 (49)	15 (49)
24 V DC power supply for the Control Unit	A	1.0	1.0	1.0
Line connection U1/L1, V1/L2, W1/L3		Stud M6, max. connectable cable cross-section 35 mm²	Stud M6, max. connectable cable cross-section 35 mm²	Stud M6, max. connectable cable cross-section 35 mm²
DC link connection, connection for the braking resistor DCP/R1, DCN, R2		Stud M6, max. connectable cable cross-section 35 mm²	Stud M6, max. connectable cable cross-section 35 mm²	Stud M6, max. connectable cable cross-section 35 mm²
Motor connection U2, V2, W2		Stud M6, max. connectable cable cross-section 35 mm²	Stud M6, max. connectable cable cross-section 35 mm²	Stud M6, max. connectable cable cross-section 35 mm²
PE connection		On housing with M6 screw	On housing with M6 screw	On housing with M6 screw
Motor cable length, max.
Shielded	m (ft)	70 (230)	70 (230)	70 (230)
Unshielded	m (ft)	100 (328)	100 (328)	100 (328)
Degree of protection		IP20	IP20	IP20
Dimensions
Width	mm (in)	275 (10.83)	275 (10.83)	275 (10.83)
Height	mm (in)	471 (18.54)	471 (18.54)	577 (22.72)
Depth
PM340	mm (in)	159.5 (6.28)	159.5 (6.28)	159.5 (6.28)
PM340 with CU310	mm (in)	240.4 (9.46)	240.4 (9.46)	240.4 (9.46)
PM340 with CUA31/CUA32	mm (in)	181.3 (7.14)	181.3 (7.14)	181.3 (7.14)
Frame size		FSD	FSD	FSE
Weight, approx.	kg (lb)	10.5 (23)	10.5 (23)	15 (33)

1) Rated output of a typical standard asynchronous motor at 400 V 3 AC. For specific sizing select drive based on motor nameplate current and overload.

Line voltage 380 … 480 V 3 AC		Liquid-cooled Power Module in blocksize format
		6SL3215-1SE31 0UA0	6SL3215-1SE31 1UA0	6SL3215-1SE31 8UA0
Output current
Rated current I_rated	A	90	110	178
Base-load currentI_H	A	80	95	155
For S6 duty (40%)I_S6	A	117	143	231
I _max	A	150	180	290
Type rating¹⁾
Based onI_rated	kW (HP)	45 (60)	55 (75)	90 (125)
Based onI_H	kW (HP)	37 (60)	45 (60)	75 (100)
Rated pulse frequency	kHz	4	4	4
Power loss
Total, approx.	kW	1.21	1.42	2.31
Lost to ambient air, approx.	kW	0.19	0.21	0.35
Cooling circuit
Rated volumetric flow for water at 70 kPa pressure drop	dm³/min (l/min)	8	8	8
Cooling circuit connection, inlet and return		Pipe thread ISO 228 – G B (external thread ’’, flat-sealing)	Pipe thread ISO 228 – G B (external thread ’’, flat-sealing)	Pipe thread ISO 228 – G B (external thread ’’, flat-sealing)
Liquid volume of integrated heat exchanger	dm³ (l)	0.13	0.2	0.2
Sound pressure level L _pA (1 m (3.28 ft)) at 50/60 Hz	dB	< 62	62	65
Rated input current with/without line reactor	A	94/105	115/129	186/204
Resistance value of the external braking resistor		15	8.2	8.2
Cable length, max. to braking resistor	m (ft)	15 (49)	15 (49)	15 (49)
24 V DC power supply for the Control Unit	A	1.0	1.0	1.0
Line connection U1/L1, V1/L2, W1/L3		M6 screw stud, max. connectable cable cross-section 35 mm²	M8 screw stud, max. connectable cable cross-section 120 mm²	M8 screw stud, max. connectable cable cross-section 120 mm²
DC link connection, connection for the braking resistor DCP/R1, DCN, R2		M6 screw stud, max. connectable cable cross-section 35 mm²	M8 screw stud, max. connectable cable cross-section 120 mm²	M8 screw stud, max. connectable cable cross-section 120 mm²
Motor connection U2, V2, W2		M6 screw stud, max. connectable cable cross-section 35 mm²	M8 screw stud, max. connectable cable cross-section 120 mm²	M8 screw stud, max. connectable cable cross-section 120 mm²
PE connection		On housing with M6 screw	On housing with M8 screw	On housing with M8 screw
Motor cable length, max.
Shielded	m (ft)	70 (230)	70 (230)	70 (230)
Unshielded	m (ft)	100 (328)	100 (328)	100 (328)
Degree of protection		IP20	IP20	IP20
Dimensions
Width	mm (in)	275 (10.83)	350 (13.78)	350 (13.78)
Height	mm (in)	577 (22.72)	660 (25.98)	660 (25.98)
Depth
PM340	mm (in)	159.5 (6.28)	241.5 (9.51)	241.5 (9.51)
PM340 with CU310	mm (in)	240.4 (9.46)	322.5 (12.70)	322.5 (12.70)
PM340 with CUA31/CUA32	mm (in)	181.3 (7.14)	263 (10.35)	263 (10.35)
Frame size		FSE	FSF	FSF
Weight, approx.	kg (lb)	15 (30)	29 (64)	29 (64)

1) Rated output of a typical standard asynchronous motor at 400 V 3 AC. For specific sizing select drive based on motor nameplate current and overload.