Options

Options

Slide rails with fixing bolts and tensioning screws according to DIN 42923

Slide rails are used to tension the belt of a machine easily and conveniently when a belt tightener is not available. They are fixed to the base using stone bolts or foundation blocks.

The assignment of slide rails to motor size can be found in DIN 42923. For motors of frame sizes 355 to 450, there are no standardized slide rails (please inquire).

Source of supply:

Lutgert & Co. GmbH
Postfach 42 51
33276 Gutersloh, Germany
Tel. +49 (0)5241-74 07-0
Fax +49 (0)5241-74 07-90

http://www.luetgert-antriebe.de
E-mail: info@luetgert-antriebe.de

Foundation block according to DIN 799

The foundation blocks are inserted into the stone foundation and embedded in concrete. They are used for fixing machines of medium size, slide rails, pedestal bearings, baseframes, etc. After the fixing bolts have been unscrewed, the machine can be dragged without it having to be lifted.

When the machine is initially installed, the foundation block that is bolted to the machine (without washers) and fitted with tapered pins is not embedded with concrete until the machine has been fully aligned. The machine is set 2 to 3 mm deeper in this case. The difference in shaft height is compensated by inserting shims on final installation. The tapered pins safeguard the exact position of the machine when it is repeatedly removed and replaced without the need for realignment.

Source of supply:

Lutgert & Co. GmbH
Postfach 42 51
33276 Gutersloh, Germany
Tel. +49 (0)5241-74 07-0
Fax +49 (0)5241-74 07-90

http://www.luetgert-antriebe.de
E-mail: info@luetgert-antriebe.de

Taper pins to DIN 258 with threaded ends and constant taper lengths

Taper pins are used for components that are repeatedly removed. The drilled hole is ground conical using a conical reamer until the pin can be pushed in by hand until the cone shoulder lies approx. 3 to 4 mm above the rim of the hole.

It can then be driven in using a hammer until it is correctly seated. The pin is removed from the drilled hole by screwing on the nut and tightening it.

Standardized taper pins are available from general engineering suppliers.

Source of supply, for example:

Otto Roth GmbH & Co. KG
Rutesheimer Stra?e 22
70499 Stuttgart, Germany
Tel. +49 (0)711-13 88-0
Fax. +49 (0)711-13 88-233

http://www.ottoroth.de
E-mail: info@ottoroth.de

Couplings for use in hazardous areas

The motor from Siemens is connected to the machine or gear unit through a coupling. Siemens is an important coupling manufacturer with a wide range of products.

For standard applications, Siemens recommends that elastic couplings of types N-EUPEX and RUPEX or torsionally rigid couplings of types ARPEX and ZAPEX are used. For special applications, FLUDEX and ELPEX-S couplings are recommended. These coupling types are suitable for use in areas subject to explosion hazards and are offered with declaration of conformity and type test certificate according to Directive 94/9/EC.

Source of supply:

Siemens contact partner - Ordering from Catalog Siemens MD 10.1 "FLENDER Standard Couplings"

or

SIEMENS AG
Kupplungswerk Mussum
Industriepark Bocholt
Schlavenhorst 100
46395 Bocholt, Germany
Tel. +49 (0)2871-92 21 85
Fax +49 (0)2871-92 25 79

http://www.siemens.com
E-mail: flendercouplings@siemens.com