SIPLUS ET 200S analog electronic modules . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS ET 200S analog electronic modules

| | | |

SIPLUS ET 200S analog electronic modules

Article number	6AG1134-4FB01-2AB0	6AG1134-4GB01-2AB0	6AG1134-4GB11-2AB0	6AG1134-4GB52-2AB0
	SIPLUS ET200S 2AI standard U	SIPLUS_ET200S 2AI I/2WIRE Standard	SIPLUS_ET200S_2AI	SIPLUS ET200S 2AI high speed
Supply voltage
Load voltage L+
? Rated value (DC)	24 V; From power module	24 V; From power module	24 V; From power module	24 V
? Short-circuit protection				Yes
? Reverse polarity protection	Yes	Yes; Destruction limit 35 mA per channel		Yes
Input current
from load voltage L+ (without load), max.	30 mA	80 mA	30 mA	225 mA
from backplane bus 3.3 V DC, max.	10 mA	10 mA	10 mA	10 mA
Output voltage
Power supply to the transmitters
? present				Yes
? short-circuit proof				Yes
Power loss
Power loss, typ.	0.6 W	0.6 W	0.6 W	2.5 W
Address area
Address space per module
? Address space per module, max.	4 byte	4 byte	4 byte	4 byte
Analog inputs
Number of analog inputs	2	2	2	2
permissible input voltage for voltage input (destruction limit), max.	35 V; 35 V continuous; 75 V for max. 1 ms (mark to space ratio 1:20)
permissible input current for current input (destruction limit), max.		40 mA	40 mA
Cycle time (all channels) max.	Number of active channels per module x basic conversion time	Number of active channels per module x basic conversion time	Number of active channels per module x basic conversion time	0.25 ms
Input ranges
? Voltage	Yes	No	No	No
? Current	No	Yes	Yes	Yes
? Thermocouple	No	No	No	No
? Resistance thermometer	No	No	No	No
? Resistance	No	No	No	No
Input ranges (rated values), voltages
? 1 V to 5 V	Yes
? -10 V to +10 V	Yes
? -5 V to +5 V	Yes
Input ranges (rated values), currents
? 0 to 20 mA				Yes
? Input resistance (0 to 20 mA)				106 ?
? -20 mA to +20 mA			Yes; 50 Ohm
? 4 mA to 20 mA		Yes; on 50 ohms	Yes; 50 Ohm	Yes
Cable length
? shielded, max.	200 m	200 m	200 m	200 m
Analog value generation for the inputs
Measurement principle	integrating	integrating	integrating
Integration and conversion time/resolution per channel
? Resolution with overrange (bit including sign), max.	14 bit; +/-10 V: 13 bits + sign, +/-5 V: 13 bits + sign; 1 to 5 V: 13 bits	13 bit; 4 to 20 mA: 13 bits	14 bit; +/-20 mA: 14 bits, 4 to 20 mA: 13 bits	16 bit
? Integration time (ms)	16,7 / 20 ms	16,7 / 20 ms	16,7 / 20 ms
? Interference voltage suppression for interference frequency f1 in Hz	50 / 60 Hz	50 / 60 Hz	50 / 60 Hz
? Conversion time (per channel)	65 ms; 55 / 65 ms	65 ms; 55 / 65 ms	65 ms; 55 / 65 ms
Smoothing of measured values
? parameterizable	Yes; In four stages by means of digital filtering	Yes; In four stages by means of digital filtering	Yes; In four stages by means of digital filtering	Yes
? Step: None	Yes; 1 x cycle time	Yes; 1 x cycle time	Yes; 1 x cycle time	Yes; 1 x cycle time
? Step: low	Yes; 4 x cycle time	Yes; 4 x cycle time	Yes; 4 x cycle time	Yes; 4 x cycle time
? Step: Medium	Yes; 32 x cycle time	Yes; 32 x cycle time	Yes; 32 x cycle time	Yes; 16 x cycle time
? Step: High	Yes; 64 x cycle time	Yes; 64 x cycle time	Yes; 64 x cycle time	Yes; 32 x cycle time
Encoder
Connection of signal encoders
? for current measurement as 2-wire transducer				Yes
— Burden of 2-wire transmitter, max.		750 ?	750 ?
Errors/accuracies
Linearity error (relative to input range), (+/-)	0.01 %	0.01 %	0.01 %	0.03 %
Temperature error (relative to input range), (+/-)	0.01 %/K	0.005 %/K	0.005 %/K	0.01 %/K
Crosstalk between the inputs, min.	-50 dB	-50 dB	-50 dB	50 dB
Repeat accuracy in steady state at 25 °C (relative to input range), (+/-)	0.05 %	0.05 %	0.05 %	0.1 %
Operational error limit in overall temperature range
? Voltage, relative to input range, (+/-)	0.6 %
? Current, relative to input range, (+/-)		0.6 %	0.6 %	0.3 %
Basic error limit (operational limit at 25 °C)
? Voltage, relative to input range, (+/-)	0.4 %
? Current, relative to input range, (+/-)		0.4 %	0.4 %	0.2 %
Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency
? Series mode interference (peak value of interference < rated value of input range), min.	70 dB	70 dB	70 dB
? Common mode interference (USS < 2.5 V) , min.	90 dB
Isochronous mode
Isochronous operation (application synchronized up to terminal)	No	No	No	Yes
Interrupts/diagnostics/status information
Alarms
? Hardware interrupt				Yes
Diagnostic messages
? Wire-break	Yes; Measuring range 1 to 5 V only	Yes	Yes; Measuring range 4 to 20 mA only	Yes; at 4 to 20 mA
? Group error	Yes	Yes	Yes	Yes
? Overflow/underflow	Yes	Yes	Yes	Yes
Diagnostics indication LED
? Group error SF (red)	Yes	Yes	Yes	Yes
Parameter
Remark	4 byte	4 byte	4 byte
Diagnostics wire break	Disable / enable (only in measuring range 1 to 5 V)		Disable / enable (only in measuring range 4 to 20 mA)	At 4 to 20 mA
Measurement type/range	deactivated / +/-5 V / 1 to 5 V / +/-10 V	deactivated / 4 to 20 mA	deactivated / +/-20 mA / 4 to 20 mA	4 to 20 mA, 0 to 20 mA
Group diagnostics	Disable / enable	Disable / enable	Disable / enable	1
Overflow/underflow	Disable / enable	Disable / enable	Disable / enable	1
Potential separation
Potential separation analog inputs
? between the channels	No	No	No	No
? between the channels and backplane bus	Yes	Yes	Yes	Yes
? Between the channels and load voltage L+	Yes	No	No	Yes
Permissible potential difference
Between the inputs and MANA (UCM)	2 V AC PP
between MANA and M internally (UISO)	75 V DC/60 V AC			75 V DC/60 V AC
Isolation
Isolation tested with	500 V DC	500 V DC	500 V DC
Standards, approvals, certificates
CE mark	Yes	Yes	Yes	Yes
UL approval		Yes	Yes
Ambient conditions
Ambient temperature during operation
? min.	-25 °C; = Tmin	-25 °C; = Tmin	-25 °C; = Tmin	-25 °C; = Tmin
? max.	70 °C; = Tmax	60 °C; = Tmax	60 °C; = Tmax	60 °C; = Tmax
Extended ambient conditions
? relative to ambient temperature-atmospheric pressure-installation altitude	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.	100 %; incl. condensation / frost permitted (no commissioning under condensation conditions)	100 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions)	100 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions)	100 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation in corrosive atmospheres!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3	Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width	15 mm	15 mm	15 mm	15 mm
Height	81 mm	81 mm	81 mm	81 mm
Depth	52 mm	52 mm	52 mm	52 mm
Weights
Weight, approx.	40 g	40 g	40 g

Article number	6AG1134-4GD00-2AB0	6AG1134-4JB51-7AB0	6AG1134-4MB02-2AB0	6AG1134-4NB01-7AB0	6AG1134-4NB51-2AB0
	SIPLUS_ET200S 4 AI I 2WIRE	SIPLUS ET200S 2AI RTD	SIPLUS_ET200S EM 2 AE I HF	SIPLUS_ET200S 2 AI TC HF	SIPLUS_ET200S 2 AI RTD HF
Supply voltage
Load voltage L+
? Rated value (DC)	24 V; From power module	24 V; From power module	24 V	24 V; From power module	24 V; From power module
? Reverse polarity protection	Yes	Yes	Yes	Yes	Yes
Input current
from load voltage L+ (without load), max.	125 mA	30 mA	48 mA	30 mA	30 mA
from backplane bus 3.3 V DC, max.	10 mA	10 mA	10 mA	10 mA	10 mA
Output voltage
Power supply to the transmitters
? present	Yes	Yes	Yes
? short-circuit proof	Yes; approx. 200 mA for module	Yes	Yes
Power loss
Power loss, typ.	0.6 W	0.6 W	1.2 W	0.6 W	0.6 W
Address area
Address space per module
? Address space per module, max.	8 byte	8 byte	4 byte	4 byte	4 byte
Analog inputs
Number of analog inputs	4	4; 2 for 3 or 4-wire connection	2	2	2
permissible input voltage for voltage input (destruction limit), max.		9 V		20 V; +/-20 V, continuous	9 V
permissible input current for current input (destruction limit), max.	30 mA; limited electronically		50 mA
Constant measurement current for resistance-type transmitter, typ.		1.67 mA			1.25 mA
Cycle time (all channels) max.	40 ms; 33 to 40 ms	Number of active channels per module x basic conversion time	0.5 ms; 0.5 ms for 2 channels without noise suppression, 18 / 21 ms per channel with noise suppression	Number of active channels per module x basic conversion time	Number of active channels per module x basic conversion time
Technical unit for temperature measurement adjustable		No		Yes; Celsius / Fahrenheit	Yes
Input ranges
? Voltage	No	No	No	Yes	Yes
? Current	Yes	No	Yes	No	No
? Thermocouple	No	No	No	Yes	Yes
? Resistance thermometer	No	Yes	No	No	Yes
? Resistance	No	Yes	No	No	Yes
Input ranges (rated values), voltages
? -80 mV to +80 mV				Yes
? Input resistance (-80 mV to +80 mV)				1 M?
Input ranges (rated values), currents
? -20 mA to +20 mA			Yes
? 4 mA to 20 mA	Yes; Into 25 Ohm		Yes
Input ranges (rated values), thermocouples
? Type B				Yes
? Input resistance (Type B)				1 M?
? Type C				Yes
? Input resistance (Type C)				1 M?
? Type E				Yes
? Input resistance (Type E)				1 M?
? Type J				Yes
? Input resistance (type J)				1 M?
? Type K				Yes
? Input resistance (Type K)				1 M?
? Type L				Yes
? Input resistance (Type L)				1 M?
? Type N				Yes
? Input resistance (Type N)				1 M?
? Type R				Yes
? Input resistance (Type R)				1 M?
? Type S				Yes
? Input resistance (Type S)				1 M?
? Type T				Yes
? Input resistance (Type T)				1 M?
Input ranges (rated values), resistance thermometer
? Cu 10					Yes
? Input resistance (Cu 10)					10 M?
? Ni 100		Yes; Standard/climate			Yes
? Input resistance (Ni 100)		2 000 k?			10 M?
? Ni 1000					Yes
? Input resistance (Ni 1000)					10 M?
? Ni 120					Yes
? Input resistance (Ni 120)					10 M?
? Ni 200					Yes
? Input resistance (Ni 200)					10 M?
? Ni 500					Yes
? Input resistance (Ni 500)					10 M?
? Pt 100		Yes; Standard/climate			Yes
? Input resistance (Pt 100)		2 000 k?			10 M?
? Pt 1000					Yes
? Input resistance (Pt 1000)					10 M?
? Pt 200					Yes
? Input resistance (Pt 200)					10 M?
? Pt 500					Yes
? Input resistance (Pt 500)					10 M?
Input ranges (rated values), resistors
? 0 to 150 ohms		Yes			Yes
? Input resistance (0 to 150 ohms)		2 000 k?			10 M?
? 0 to 300 ohms		Yes			Yes
? Input resistance (0 to 300 ohms)		2 000 k?			10 M?
? 0 to 600 ohms		Yes			Yes
? Input resistance (0 to 600 ohms)		2 000 k?			10 M?
? 0 to 3000 ohms					Yes
? Input resistance (0 to 3000 ohms)					10 M?
Thermocouple (TC)
Temperature compensation
— internal temperature compensation				Yes; possible with TM-E15S24-AT, TM-E15C24-AT	Yes
— external temperature compensation with compensations socket				Yes; one external compensating box per channel
Characteristic linearization
? parameterizable		Yes; for Pt100, Ni100		Yes	Yes; for Ptxxx, Nixxx
— for thermocouples				Type B, C, E, J, K, L, N, R, S, T to IEC 584
— for resistance thermometer		Pt100 (standard, climatic range), Ni100 (standard, climatic range)			Ptxxx, Nixxx
Cable length
? shielded, max.	200 m	200 m	200 m	50 m	200 m
Analog value generation for the inputs
Measurement principle	integrating	integrating	Sigma Delta	integrating	integrating (Sigma-Delta)
Integration and conversion time/resolution per channel
? Resolution with overrange (bit including sign), max.	13 bit; 4 to 20 mA: 13 bits	16 bit; 150 ohms: 14 bits; 300, 600 ohms: 15 bits, Pt100, Ni100: 16 bits	16 bit	16 bit	16 bit; for Pt100, Ni100, Ni120, Pt200, Ni200, Pt 500, Ni 500, Pt1000, Ni1000, Cu10: 15 bits + sign; for 150, 300, 600, 3000 ohms: 15 bits; for PTC: 1 bits
? Integration time, parameterizable	Yes	Yes	Yes
? Integration time (ms)	16,67 / 20 ms	16,7 / 20 ms		16,7 / 20 ms	16,7 / 20 ms
? Interference voltage suppression for interference frequency f1 in Hz	50 / 60 Hz	50 / 60 Hz	60 / 50 Hz / no	50 / 60 Hz	50 / 60 Hz
? Conversion time (per channel)		66 / 80 ms; additional conversion time for diagnostic wire break test	0.04 ms; Without noise suppression 17/20 ms per channel with error	66 ms; 66 / 80 ms; additional conversion time for diagnostic wire break test	Basic conversion time incl. integration time: 50 / 60 ms; additional conversion time for diagnostics of wire break test: 5 / 5 ms; additional conversion time for line compensation with 3-wire connection: 50 / 60 ms
Smoothing of measured values
? parameterizable	Yes; in 4 stages	Yes; In four stages by means of digital filtering	Yes; In 4 stages: 1 x, 4 x, 16 x, 32 x cycle time	Yes; In four stages by means of digital filtering	Yes; In four stages by means of digital filtering
? Step: None	Yes; 1 x cycle time	Yes; 1 x cycle time	Yes; 1x	Yes; 1 x cycle time	Yes; 1 x cycle time
? Step: low	Yes; 4 x cycle time	Yes; 4 x cycle time	Yes; 4x	Yes; 4 x cycle time	Yes; 4 x cycle time
? Step: Medium	Yes; 16 x cycle time	Yes; 32 x cycle time	Yes; 16x	Yes; 32 x cycle time	Yes; 32 x cycle time
? Step: High	Yes; 32 x cycle time	Yes; 64 x cycle time	Yes; 32x	Yes; 64 x cycle time	Yes; 64 x cycle time
Encoder
Connection of signal encoders
? for current measurement as 2-wire transducer
— Burden of 2-wire transmitter, max.	750 ?		750 ?
? for resistance measurement with two-wire connection		Yes			Yes
? for resistance measurement with three-wire connection		Yes			Yes; internal compensation of the line resistances
? for resistance measurement with four-wire connection		Yes			Yes
Errors/accuracies
Linearity error (relative to input range), (+/-)	0.01 %	0.01 %	0.03 %	0.01 %	0.01 %
Temperature error (relative to input range), (+/-)	0.003 %/K	0.005 %/K	0.03 %/K	0.005 %/K	0.0009 %/K
Crosstalk between the inputs, min.	-50 dB	-50 dB	-100 dB	-50 dB	-50 dB
Repeat accuracy in steady state at 25 °C (relative to input range), (+/-)	0.05 %	0.05 %	0.01 %	0.05 %	0.05 %
Operational error limit in overall temperature range
? Voltage, relative to input range, (+/-)				0.1 %; +/-1.5 K for thermocouples, +/-7 K for thermocouples type C,+/-2.5 K with static thermal state (ambient temperature change < 0.3 K/min)
? Current, relative to input range, (+/-)	0.5 %		0.1 %; 0.2% without interference frequency suppression
? Resistance thermometer, relative to input range, (+/-)		0.6 %			Resistance-type transmitter: +/-0.1%; Pt100, Pt200, Pt500, Pt1000 standard: +/-1.0 K; Pt100, Pt200, Pt500, Pt1000 climate: +/-0.25 K; Ni100, Ni120, Ni200, Ni500, Ni1000 standard and climate: +/-0.4 K; Cu10 +/-1.5 K
Basic error limit (operational limit at 25 °C)
? Voltage, relative to input range, (+/-)				0.05 %; +/-1 K with thermocouples, +/-5 K with thermocouples type C, +/-1.5 K with static thermal state (ambient temperature change < 0.3 K/min)
? Current, relative to input range, (+/-)	0.3 %		0.05 %; 0.1% without interference frequency suppression
? Resistance thermometer, relative to input range, (+/-)		0.4 %			Resistance-type transmitter: +/-0.05%; Pt100, Pt200, Pt500, Pt1000 standard: +/-0.6 K; Pt100, Pt200, Pt500, Pt1000 climate: +/-0.13 K; Ni100, Ni120, Ni200, Ni500, Ni1000 standard and climate: +/-0.2 K; Cu10 +/-1 K
Interference voltage suppression for f = n x (f1 +/- 1 %), f1 = interference frequency
? Series mode interference (peak value of interference < rated value of input range), min.	70 dB	70 dB	90 dB	70 dB	70 dB
? Common mode interference (USS < 2.5 V) , min.		90 dB	100 dB	90 dB	90 dB
Isochronous mode
Isochronous operation (application synchronized up to terminal)	No	No	Yes		No
Interrupts/diagnostics/status information
Alarms
? Hardware interrupt			Yes
Diagnostic messages
? Wire-break	Yes; Measuring range 1 to 5 V only	Yes	Yes; Measuring range 4 to 20 mA only	Yes; only thermocouples	Yes
? Group error	Yes	Yes	Yes	Yes	Yes
? Overflow/underflow	Yes	Yes	Yes	Yes	Yes
Diagnostics indication LED
? Group error SF (red)	Yes	Yes	Yes	Yes	Yes
Parameter
Remark	7 byte		12 bytes, 4 bytes in compatibility mode	4 byte	7 byte
Diagnostics wire break	1	Disable / enable	Disable / enable	Disable / enable (wire break is detected only in thermocouples)	Disable / enable
Measurement type/range	1	deactivated/150 ohms/; 300 ohms/600 ohms/ Pt100 climatic/ Pt100 standard; Ni100 standard / Ni100 climatic, 2, 3 or 4-wire	deactivated / +/-20 mA / 4 to 20 mA	Deactivated/ +/- 80 mV/ TC-EL Type T (Cu-CuNi)/ TC-EL Type K (NiCr-Ni)/ TC-EL Type B (PtRh-PtRh)/ TC-EL Type c (Wer-Wer) TC-EL Type N (NiCrSi-NiSi)/ TC-EL Type E (NiCr-CuNi)/ TC-EL Type R (PtRh-Pt)/ TC-EL Type S (PtRh-Pt)/ TC-EL Type J (Fe-Cu-Ni)/ TC	Deactivated/ 150 Ohm / 300 Ohm / 600 Ohm /Pt100/Pt200/Pt500/Pt1000 each standard or climate range / Ni100/Ni120/Ni200/Ni500/Ni1000 each standard or climate range / Cu10 each standard or climate range / PTC
Group diagnostics	1	Disable / enable	Disable / enable	Disable / enable	Disable / enable
Overflow/underflow	1	Disable / enable	Disable / enable	Disable / enable	Disable / enable
Comparison point				none / yes, internal
Potential separation
Potential separation analog inputs
? between the channels	No	No	No; however, increased permissible potential difference between the inputs.	No	No
? between the channels and backplane bus	Yes	Yes	Yes	Yes	Yes
? Between the channels and load voltage L+	No	Yes	Yes	Yes	Yes
Permissible potential difference
Between the inputs and MANA (UCM)				140 V DC/100 V AC
between MANA and M internally (UISO)		75 V DC/60 V AC		75 V DC/60 V AC	75 V DC/60 V AC
Isolation
Isolation tested with	500 V DC	500 V DC		500 V DC	500 V DC
Standards, approvals, certificates
CE mark	Yes	Yes	Yes	Yes	Yes
Ambient conditions
Ambient temperature during operation
? min.	-25 °C; = Tmin	-25 °C; = Tmin	-25 °C; = Tmin	0 °C; = Tmin	-25 °C; = Tmin
? max.	70 °C; = Tmax	70 °C; = Tmax	70 °C; = Tmax	70 °C; = Tmax	60 °C; = Tmax
Extended ambient conditions
? relative to ambient temperature-atmospheric pressure-installation altitude	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions)	100 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions)	100 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions)	100 %; Relative humidity, incl. condensation / frost permitted (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation in corrosive atmospheres!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width	15 mm	15 mm	15 mm	15 mm	15 mm
Height	81 mm	81 mm	81 mm	81 mm	81 mm
Depth	52 mm	52 mm	52 mm	52 mm	52 mm
Weights
Weight, approx.	40 g	40 g	45 g	40 g	40 g

Article number	6AG1135-4FB01-2AB0	6AG1135-4GB01-2AB0	6AG1135-4LB02-7AB0
	SIPLUS ET200S EM 2AO U	SIPLUS_ET200S 2AO I Standard	SIPLUS ET200S 2AO U high feature
Supply voltage
Load voltage L+
? Rated value (DC)	24 V; From power module	24 V; From power module	24 V
? Reverse polarity protection	Yes	Yes	Yes
Input current
from load voltage L+ (without load), max.	130 mA	150 mA	80 mA
from backplane bus 3.3 V DC, max.	10 mA	10 mA	10 mA
Power loss
Power loss, max.	2 W	2 W	1.2 W
Address area
Address space per module
? Address space per module, max.	4 byte	4 byte	4 byte
Analog outputs
Number of analog outputs	2	2	2
Voltage output, short-circuit protection	Yes		Yes
Voltage output, short-circuit current, max.	25 mA		25 mA
Current output, no-load voltage, max.		18 V
Cycle time (all channels) max.	1.5 ms	1.5 ms	0.5 ms; At max. 0.5 µF
Output ranges, voltage
? 1 V to 5 V	Yes		Yes
? -5 V to +5 V			Yes
? -10 V to +10 V	Yes		Yes
Output ranges, current
? -20 mA to +20 mA		Yes
? 4 mA to 20 mA		Yes
Connection of actuators
? for voltage output two-wire connection	Yes; Without compensation of the line resistances		Yes
? for voltage output four-wire connection	Yes		Yes
? for current output two-wire connection		Yes
? for current output four-wire connection		No
Load impedance (in rated range of output)
? with voltage outputs, min.	1 k?		1 k?
? with voltage outputs, capacitive load, max.	1 µF		0.5 µF
? with current outputs, max.		500 ?
? with current outputs, inductive load, max.		1 mH
Destruction limits against externally applied voltages and currents
? Voltages at the outputs towards MANA	15 V; max. 15 V continuous; 75 V for max. 1 s (mark to space ratio 1:20)	15 V; max. 15 V continuous; 75 V for max. 1 s (mark to space ratio 1:20)	15 V; max. 15 V continuous; 75 V for max. 1 s (mark to space ratio 1:20)
? Current, max.	50 mA; DC	50 mA; DC
Cable length
? shielded, max.	200 m	200 m	200 m; 100m if Twa < 2ms
Analog value generation for the outputs
Integration and conversion time/resolution per channel
? Resolution with overrange (bit including sign), max.	14 bit; 1 to 5 V: 12 bits, +/-10 V: 13 bits + sign	14 bit; 4 to 20 mA: 13 bits, +/-20 mA: 14 bits	16 bit; 15 bit + sign
Settling time
? for resistive load	0.1 ms	0.1 ms	0.2 ms
? for capacitive load	0.5 ms	0.5 ms	0.5 ms; At max. 0.5 µF
? for inductive load	0.5 ms	0.5 ms	0.5 ms
Errors/accuracies
Output ripple (relative to output range, bandwidth 0 to 50 kHz), (+/-)	0.02 %	0.02 %	0.02 %
Linearity error (relative to output range), (+/-)	0.02 %	0.02 %	0.01 %
Temperature error (relative to output range), (+/-)	0.01 %/K	0.01 %/K
Crosstalk between the outputs, min.			60 dB
Repeat accuracy in steady state at 25 °C (relative to output range), (+/-)	0.05 %	0.05 %	0.01 %
Operational error limit in overall temperature range
? Voltage, relative to output range, (+/-)	0.4 %		0.1 %
? Current, relative to output range, (+/-)		0.5 %
Basic error limit (operational limit at 25 °C)
? Voltage, relative to output range, (+/-)	0.2 %		0.05 %
? Current, relative to output range, (+/-)		0.3 %
Isochronous mode
Isochronous operation (application synchronized up to terminal)			Yes
Interrupts/diagnostics/status information
Substitute values connectable	Yes; 0 to 65535 (range of values must be within the rated range)	Yes; 0 to 65535 (range of values must be within the rated range)	Yes
Diagnostic messages
? Diagnostic information readable			Yes
? Wire-break		Yes
? Short-circuit	Yes		Yes
? Group error	Yes	Yes	Yes
Diagnostics indication LED
? Group error SF (red)	Yes	Yes	Yes
Parameter
Remark	7 byte	7 byte	7 byte
Diagnostics wire break		Disable / enable
Diagnostics short-circuit	Disable / enable		Disable / enable
Output type/range	deactivated / 1 to 5 V / +/ -10 V	deactivated / +/-20 mA / 4 to 20 mA	deactivated / 1 to 5 V / +/ -10 V / +/- 5 V
Group diagnostics	Disable / enable	Disable / enable	Disable / enable
Response to CPU/master STOP	Output current and de-energized/substitute a value/keep last value	Output current and de-energized/substitute a value/keep last value	Output current and de-energized/substitute a value/keep last value
Potential separation
Potential separation analog outputs
? between the channels	No	No	No
? between the channels and backplane bus	Yes	Yes	Yes
? Between the channels and load voltage L+	Yes	Yes	Yes
Permissible potential difference
between MANA and M internally (UISO)	75 V DC/60 V AC	75 V DC/60 V AC	75 V DC/60 V AC
Isolation
Isolation tested with			500 V DC
Ambient conditions
Ambient temperature during operation
? min.	-25 °C; = Tmin	-25 °C; = Tmin	-25 °C; = Tmin
? max.	60 °C; = Tmax	70 °C; = Tmax	60 °C; = Tmax
Extended ambient conditions
? relative to ambient temperature-atmospheric pressure-installation altitude	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)	Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)	100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation in corrosive atmospheres!	Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!	Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width	15 mm	15 mm	15 mm
Height	81 mm	81 mm	81 mm
Depth	52 mm	52 mm	52 mm
Weights
Weight, approx.	40 g	40 g	40 g

skener.ru

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
Бесконтактные выключатели Конечные выключатели Оптические датчики Энкодеры

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FS - Установка умягчения

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FK - Установка обезжелезивания