SIPLUS S7-300 FM 350-2 . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS S7-300 FM 350-2

| | | | | | |

SIPLUS S7-300 FM 350-2

Article number		6AG1350-2AH01-4AE0
		SIPLUS S7-300 FM350-2
Supply voltage
Auxiliary voltage 1L+, load voltage 2L+
? Rated value (DC)		24 V
Input current
from load voltage L+ (without load), max.		150 mA
from backplane bus 5 V DC, max.		100 mA
Encoder supply
Type of output voltage		NAMUR-encoder supply: 8.2 V +/-2%
Short-circuit protection		Yes
Output current
? Rated value		200 mA
Power loss
Power loss, typ.		10 W
Digital inputs
Number of digital inputs		8
Number of NAMUR inputs		8
Functions		1 each for gate start/ gate stop
Input voltage
? for signal "0"		-3 to +5V
? for signal "1"		11 to 30.2 V
Input current
? for signal "0", max. (permissible quiescent current)		2 mA
? for signal "1", typ.		9 mA
Input delay (for rated value of input voltage)
for standard inputs
— at "0" to "1", max.		50 µs
Cable length
? shielded, max.		100 m
Digital outputs
Number of digital outputs		8
Short-circuit protection		Yes
Limitation of inductive shutdown voltage to		L+ (-40 V)
Output voltage
? for signal "1", min.		L+ (-0.8 V)
Output current
? for signal "1" rated value		0.5 A
? for signal "0" residual current, max.		0.5 mA
Output delay with resistive load
? "0" to "1", max.		300 µs
Switching frequency
? with resistive load, max.		500 Hz
? with inductive load, max.		0.5 Hz
Total current of the outputs (per group)
horizontal installation
— up to 40 °C, max.		4 A
— up to 60 °C, max.		2 A
all other mounting positions
— up to 40 °C, max.		2 A
Cable length
? shielded, max.		600 m
? unshielded, max.		100 m
Encoder
Connectable encoders
? Incremental encoder (asymmetrical)		Yes
? 24 V initiator		Yes
? 24 V directional element		Yes
? NAMUR encoder		Yes
? 2-wire sensor		Yes
NAMUR encoder
? Input signal		to DIN 19 234
? Input current for signal "0", max.		1.2 mA
? Input current for signal "1", min.		2.1 mA
? Input delay, max.		50 µs
? Input frequency, max.		20 kHz
? Cable length, shielded, max.		100 m
Interrupts/diagnostics/status information
Diagnostic functions		Yes; Diagnostic information readable
Alarms
? Diagnostic alarm		Yes; Parameterizable
? Hardware interrupt		Yes; Parameterizable
Counter input 24 V
? Number		8; 32 bit or ±31 bit
? Input voltage for signal "0"		-3 to +5V
? Input voltage for signal "1"		11 to 30.2 V
? Input current for signal "0", max. (permissible quiescent current)		2 mA
? Input current for signal "1", typ.		9 mA
? Input delay, max.		50 µs
? Counting frequency, max.		20 kHz; Incremental encoder: 10 kHz
? Cable length, max.		100 m
Potential separation
Potential separation digital inputs
? between the channels and backplane bus		Yes; and shielding
Potential separation digital outputs
? between the channels and backplane bus		Yes; and shielding
Potential separation counter
? between the channels and backplane bus		Yes; and shielding
Standards, approvals, certificates
CE mark		Yes
UL approval		Yes; File E239877
FM approval		Yes
RCM (formerly C-TICK)		Yes
KC approval		Yes
EAC (formerly Gost-R)		Yes
Ambient conditions
Ambient temperature during operation
? min.		0 °C; = Tmin
? max.		60 °C; = Tmax
Extended ambient conditions
? relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Connection method
required front connector		1x 40-pin
Dimensions
Width		80 mm
Height		125 mm
Depth		120 mm
Weights
Weight, approx.		460 g

skener.ru

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
Бесконтактные выключатели Конечные выключатели Оптические датчики Энкодеры

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FS - Установка умягчения

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FK - Установка обезжелезивания