6ES7 153-2BA02-0XB0

General information

Vendor identification (VendorID)

801Eh

Supply voltage

24 V DC

Yes

permissible range, lower limit (DC)

20.4 V

permissible range, upper limit (DC)

28.8 V

permissible range (ripple included), lower limit (DC)

20.4 V

permissible range (ripple included), upper limit (DC)

28.8 V

External protection for supply cables (recommendation)

2.5 A

Mains buffering

• Mains/voltage failure stored energy time

5 ms

Input current

Current consumption, max.

600 mA

Rated value at 24 V DC

650 mA

Inrush current, typ.

3 A

I t

0.1 A ·s

Output voltage

Rated value, 5 V DC

Yes

Output current

for backplane bus (5 V DC), max.

1.5 A

Power losses

Power loss, typ.

5.5 W

Address area

Addressing volume

• Outputs

244 byte

• Inputs

244 byte

Hardware configuration

Number of modules per DP slave interface, max.

12

Time stamping

Accuracy

1 ms; 1ms at up to 8 modules; 10ms at up to 12 modules

Number of message buffers

15

Messages per message buffer

20

Number of stampable digital inputs, max.

128; Max. 128 signals/station; max. 32 signals/slot

Time format

RFC 1119

Time resolution

0.466 ns

Time interval for transmitting the message buffer if a message is present

1 000 ms

Time stamp on signal change

rising / falling edge as signal entering or exiting

Interfaces

Interface physics, RS 485

Yes

Interface physics, FOC

No

PROFIBUS DP

• Node addresses

1 to 125 permitted

• Automatic detection of transmission speed

Yes

• PROFIBUS DP, output current, max.

70 mA

• Transmission procedure

RS 485

• Transmission rate, max.

12 Mbit/s

• SYNC capability

Yes

• FREECE capability

Yes

• Direct data exchange (slave-to-slave communication)

Yes; Sender

• PROFIBUS DP

9-pin sub D

1st interface

DP slave

• GSD file

SI04801.GSG

• Automatic baud rate search

Yes

Communication functions

Bus protocol/transmission protocol

PROFIBUS DP to EN 50170

Isolation

Isolation checked with

Isolation voltage 500 V

Ambient conditions

Operating temperature

• Min.

0 °C

• max.

60 °C

Air pressure

• Operating altitude above sea level, max.

3 000 m

Degree and class of protection

IP20

Yes

Configuration

Configuration software

• STEP 7

Yes; STEP 7 / COM PROFIBUS / non-Siemens tools via GSD file

Dimensions

Width

40 mm

Height

125 mm

Depth

117 mm

Weight

Weight, approx.

360 g

6ES7 197-1LB00-0XA0

General system features

Requirements for DP master system

• Length of parameter assignment message

244 byte

Supply voltage

Description

via bus module

permissible range, lower limit (DC)

20.4 V

permissible range, upper limit (DC)

28.8 V

Interfaces

PROFIBUS DP

• Properties of the lower-level DP master systems

• Transmission rate, max.

12 Mbit/s; 45.45 kbit/s to 12 Mbit/s

• Termination of lower-level DP master system

Active terminating resistor (Bus Terminator)

• Use of OLM/OBT

Yes

• Use of RS 485 repeaters, max.

9

• Number of DP slaves, max.

31; 64 when using RS 485 repeaters or OLM/OBT

Protocols

Further protocols

• PROFIBUS DP protocol

Yes

Interrupts/diagnostics/status information

Status indicator

No

Alarms

• Alarms

No

Diagnoses

• Diagnostic functions

Yes

Galvanic isolation

to lower-level DP master system

Yes

Dimensions

Width

40 mm

Height

125 mm

Depth

130 mm

Weight

Weight, approx.

200 g