General(based on DIN EN 61207/IEC 1207. All data refers to the binary gas mixture H₂ in N₂)

Measuring ranges

4, internally and externally switchable; automatic measuring range switchover also possible

Span

Application-dependent (see ordering data)

Measuring ranges with suppressed zero point

Application-dependent (see ordering data)

Operating position

Front wall, vertical

Conformity

CE marking in accordance with EN 50081-1/EN 50081-2 and RoHS

Design, enclosure

Degree of protection

IP65 according to EN 60529

Weight

Approx. 25 kg

Electrical characteristics

EMC (ElectromagneticCompatibility)

In accordance with standard requirements of NAMUR NE21 (08/98) and EN 61326

Electrical safety

In accordance with EN 61010-1; overvoltage category II

Power supply (see nameplate)

100 AC -10 % ... 120 V AC +10 %, 47 ... 63 Hz

or

200 AC -10 % ... 240 V AC +10 %, 47 ... 63 Hz

Power consumption

• Approx. 25 VA (gas connection block unheated)
• Approx. 330 VA (gas connection block heated)

Fuse values (gas connection unheated)

100 ... 120 V

F3 1T/250

F4 1T/250

200 ... 240 V

F3 0.63T/250

F4 0.63T/250

Fuse values (gas connection heated)

100 ... 120 V

F1 1T/250

F2 4T/250

F3 4T/250

F4 4T/250

200 ... 240 V

F1 0.63T/250

F2 2.5T/250

F3 2.5T/250

F4 2.5T/250

Gas inlet conditions

Sample gas pressure

800 ... 1 100 hPa (absolute)

Sample gas flow

30 ... 90 l/h

Sample gas temperature

Min. 0 to max. 50 °C, but above the dew point

Temperature

• of the measuring cell (sensor)

70 C

• of the measureming cell block (base)

80 C (heated)

Sample gas humidity

< 90% relative humidity

Purging gas pressure

• Permanent

165 hPa above ambient pressure

• For short periods

Max. 250 hPa above ambient pressure

Dynamic response(the dynamic and measuring response refers to the measurement of H₂ in N₂)
(referred to sample gas pressure 1 000 hPa absolute, sample gas flow 0.5 l/min, and ambient temperature 25 °C)

Warm-up period

< 30 min at room temperature (the technical specification will be met after 2 hours)

Delayed display (T₉₀)

Approx. 35 s (including dead time)

Electrical damping

0 ... 100 s, parameterizable

Dead time (the diffusion to the probes is the determining variable)

Approx. 34 s

Measuring response(the dynamic and measuring response refers to the measurement of H₂ in N₂)
(referred to sample gas pressure 1 000 hPa absolute, sample gas flow 0.5 l/min, and ambient temperature 25 °C)

Output signal fluctuation (3 value)

< ± 1% of the smallest possible span according to rating plate with electronic damping constant of 1 s

Zero point drift

< ± 1% of the current span/week

Measured-value drift

< ± 1% of the smallest possible span (according to rating plate)/week

Repeatability

< ± 1% of the current span

Detection limit

1% of the smallest possible span according to rating plate

Linearity error

< ± 1% of the current span

Influencing variables(referred to sample gas pressure 1 000 hPa absolute, sample gas flow 0.5 l/min, and ambient temperature 25 °C)

Ambient temperature

< 2%/10 K referred to smallest possible span according to rating plate

Accompanying gases

Deviation from zero point (for influence of interfering gas, see section "Cross-interference")

Sample gas flow

0.2% of the current measuring span with a change in flow of 0.1 l/min within the permissible flow range

Sample gas pressure

< 1 % of the span with a change in pressure of 100 hPa

Power supply

< 0.1% of the output signal span with rated voltage ± 10%

Electrical inputs and outputs

Analog output

0/2/4 ... 20 mA, isolated; max. load 750 

Relay outputs

6, with changeover contacts, freely parameterizable, e.g. for measuring range identification; load: 24 V AC/DC/1 A, isolated

Analog inputs

2, dimensioned for 0/2/4 … 20 mA for external pressure sensor and correction of cross-interference

Binary inputs

6, designed for 24 V, isolated, freely parameterizable, e.g. for measuringrange switchover

Serial interface

RS 485

Options

AUTOCAL function with 8 additional binary inputs and 8 additional relay outputs, also with PROFIBUS PA (on request) or PROFIBUS DP (on request)

Climatic conditions

Permissible ambient temperature

-40 ... +70 °C during storage and transportation, 5 … 45 °C during operation

Permissible humidity (dew point must not be fallen below)

< 90 % relative humidity as annual average, during storage and transportation