SIPLUS Y-link for S7-400H . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIPLUS Y-link for S7-400H

| | | | | | |

SIPLUS Y-link for S7-400H

Article number		6AG1153-2BA10-7XB0
		SIPLUS ET200M IM153-2 HF
Supply voltage
Rated value (DC)
? 24 V DC		Yes
permissible range (ripple included), lower limit (DC)		20.4 V
permissible range (ripple included), upper limit (DC)		28.8 V
external protection for power supply lines (recommendation)		2,5 A
Mains buffering
? Mains/voltage failure stored energy time		5 ms
Input current
Current consumption, max.		650 mA; with 24 V DC supply
Inrush current, typ.		3 A
I?t		0.1 A?·s
Output current
for backplane bus (5 V DC), max.		1.5 A
Power loss
Power loss, typ.		5.5 W
Address area
Addressing volume
? Inputs		244 byte
? Outputs		244 byte
Hardware configuration
Number of modules per DP slave interface, max.		12
Time stamping
Accuracy		1 ms; 1ms at up to 8 modules; 10ms at up to 12 modules
Number of message buffers		15
Messages per message buffer		20
Number of stampable digital inputs, max.		128; Max. 128 signals/station; max. 32 signals/slot
Time format		RFC 1119
Time resolution		0.466 ns
Time interval for transmitting the message buffer if a message is present		1 000 ms
Time stamp on signal change		rising / falling edge as signal entering or exiting
Interfaces
Interface physics, RS 485		Yes
Interface physics, FOC		No
PROFIBUS DP
? Node addresses		1 to 125 permitted
? automatic detection of transmission rate		Yes
? Output current, max.		70 mA
? Transmission rate, max.		12 Mbit/s
? Transmission procedure		RS 485
? SYNC capability		Yes
? FREEZE capability		Yes
? Direct data exchange (slave-to-slave communication)		Yes; as publisher with all IO, as subscriber with F-IO only
? Connector type		9-pin sub D
1. Interface
DP slave
? GSD file		SI05801E.GSG
? automatic baud rate search		Yes
Protocols
Bus protocol/transmission protocol		PROFIBUS DP to EN 50170
Isolation
Isolation tested with		Isolation voltage 500 V
Degree and class of protection
Degree of protection acc. to EN 60529
? IP20		Yes
Standards, approvals, certificates
CE mark		Yes
Ambient conditions
Ambient temperature during operation
? min.		-40 °C; = Tmin; Startup @ -25 °C
? max.		70 °C; = Tmax
Ambient temperature during storage/transportation
? min.		-40 °C
? max.		70 °C
Extended ambient conditions
? relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
? At cold restart, min.		-25 °C
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Configuration
Configuration software
? STEP 7		Yes; STEP 7 / COM PROFIBUS / non-Siemens tools via GSD file
Dimensions
Width		40 mm
Height		125 mm
Depth		117 mm
Weights
Weight, approx.		360 g

Article number		6AG1197-1LB00-4XA0
		SIPLUS S7 Y-Koppler
General information
Requirements for DP master system
? Length of parameter assignment telegram		244 byte
Supply voltage
Design of the power supply		via bus module
Interfaces
PROFIBUS DP
Properties of the lower-level DP master system
— Transmission rate, max.		12 Mbit/s; 45.45 kbit/s to 12 Mbit/s
— Termination of lower-level DP master system		Active terminating resistor (Bus Terminator)
— Use of OLM/OBT		Yes
— Use of RS 485 repeaters, max.		9
— Number of DP slaves, max.		31; 64 when using RS 485 repeaters or OLM/OBT
Protocols
PROFIBUS DP		Yes
Interrupts/diagnostics/status information
Status indicator		No
Alarms		No
Diagnostic functions		Yes
Potential separation
to lower-level DP master system		Yes
Ambient conditions
Ambient temperature during operation
? min.		0 °C; = Tmin
? max.		60 °C; = Tmax
Ambient temperature during storage/transportation
? min.		-40 °C
? max.		70 °C
Extended ambient conditions
? relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Dimensions
Width		40 mm
Height		125 mm
Depth		130 mm
Weights
Weight, approx.		200 g

Article number		6AG1195-7HD10-2XA0
		SIPLUS_ET200M_DP_Busmodul
Standards, approvals, certificates
CE mark		Yes
UL approval		Yes; File E239877
FM approval		Yes; CofC 3028431
RCM (formerly C-TICK)		Yes
KC approval		Yes
EAC (formerly Gost-R)		Yes
Ambient conditions
Ambient temperature during operation
? min.		-40 °C; = Tmin
? max.		70 °C; = Tmax; 60 °C @ UL/cUL, ATEX and FM use
Ambient temperature during storage/transportation
? min.		-40 °C
? max.		70 °C
Extended ambient conditions
? relative to ambient temperature-atmospheric pressure-installation altitude		Tmin ... Tmax at 1080 hPa ... 795 hPa (-1000 m ... +2000 m) // Tmin ... (Tmax - 10K) at 795 hPa ... 658 hPa (+2000 m ... +3500 m) // Tmin ... (Tmax - 20K) at 658 hPa ... 540 hPa (+3500 m ... +5000 m)
Relative humidity
— With condensation, tested in accordance with IEC 60068-2-38, max.		100 %; RH incl. condensation/frost (no commissioning under condensation conditions)
Resistance
— against biologically active substances / conformity with EN 60721-3-3		Yes; Class 3B2 mold, fungus and dry rot spores (with the exception of fauna). The supplied connector covers must remain on the unused interfaces during operation!
— against chemically active substances / conformity with EN 60721-3-3		Yes; Class 3C4 (RH < 75%) incl. salt spray according to EN 60068-2-52 (degree of severity 3). The supplied connector covers must remain on the unused interfaces during operation!
— against mechanically active substances / conformity with EN 60721-3-3		Yes; Class 3S4 incl. sand, dust. The supplied connector covers must remain on the unused interfaces during operation!
Accessories
belongs to product		ET 200M
Dimensions
Width		97 mm
Height		92 mm
Depth		30 mm
Weights
Weight, approx.		133 g