Y-link for S7-400H . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на Y-link for S7-400H

| | | | | | |

Y-link for S7-400H

Order number		6ES7153-2BA70-0XB0
		ET200M, INTERFACE IM153-2 HF OUTDOOR
General information
Vendor identification (VendorID)		801Eh
Supply voltage
Rated value (DC)
? 24 V DC		Yes
permissible range (ripple included), lower limit (DC)		20.4 V
permissible range (ripple included), upper limit (DC)		28.8 V
external protection for power supply lines (recommendation)		2,5 A
Mains buffering
? Mains/voltage failure stored energy time		5 ms
Input current
Current consumption, max.		650 mA
Inrush current, typ.		3 A
I?t		0.1 A?·s
Output current
for backplane bus (5 V DC), max.		1.5 A
Power loss
Power loss, typ.		5.5 W
Address area
Addressing volume
? Inputs		244 byte
? Outputs		244 byte
Hardware configuration
Number of modules per DP slave interface, max.		12
Time stamping
Accuracy		1 ms; 1ms at up to 8 modules; 10ms at up to 12 modules
Number of message buffers		15
Messages per message buffer		20
Number of stampable digital inputs, max.		128; Max. 128 signals/station; max. 32 signals/slot
Time format		RFC 1119
Time resolution		0.466 ns
Time interval for transmitting the message buffer if a message is present		1 000 ms
Time stamp on signal change		rising / falling edge as signal entering or exiting
Interfaces
Interface physics, RS 485		Yes
Interface physics, FOC		No
PROFIBUS DP
? Node addresses		1 to 125 permitted
? automatic detection of transmission rate		Yes
? Output current, max.		70 mA
? Transmission rate, max.		12 Mbit/s
? Transmission procedure		RS 485
? SYNC capability		Yes
? FREEZE capability		Yes
? Direct data exchange (slave-to-slave communication)		Yes; as publisher with all IO, as subscriber with F-IO only
? Connector type		9-pin sub D
1. Interface
DP slave
? GSD file		SI05801E.GSG
? automatic baud rate search		Yes
Protocols
Bus protocol/transmission protocol		PROFIBUS DP to EN 50170
Isolation
Isolation tested with		Isolation voltage 500 V
Degree and class of protection
Degree of protection acc. to EN 60529
? IP20		Yes
Air pressure acc. to IEC 60068-2-13
? Installation altitude above sea level, max.		3 000 m
Configuration
Configuration software
? STEP 7		Yes; STEP 7 / COM PROFIBUS / non-Siemens tools via GSD file
Dimensions
Width		40 mm
Height		125 mm
Depth		117 mm
Weights
Weight, approx.		360 g

Order number		6ES7197-1LB00-0XA0
		Y-COUPLER F. BUILDING Y-LINK, REDUNDANT
General information
Requirements for DP master system
? Length of parameter assignment telegram		244 byte
Supply voltage
Design of the power supply		via bus module
permissible range, lower limit (DC)		20.4 V
permissible range, upper limit (DC)		28.8 V
Interfaces
PROFIBUS DP
Properties of the lower-level DP master system
— Transmission rate, max.		12 Mbit/s; 45.45 kbit/s to 12 Mbit/s
— Termination of lower-level DP master system		Active terminating resistor (Bus Terminator)
— Use of OLM/OBT		Yes
— Use of RS 485 repeaters, max.		9
— Number of DP slaves, max.		31; 64 when using RS 485 repeaters or OLM/OBT
Protocols
PROFIBUS DP		Yes
Interrupts/diagnostics/status information
Status indicator		No
Alarms		No
Diagnostic functions		Yes
Potential separation
to lower-level DP master system		Yes
Dimensions
Width		40 mm
Height		125 mm
Depth		130 mm
Weights
Weight, approx.		200 g