Configuration instructions when using an operator panel with display and/or a decoupling module with SIMOCODE pro V with PROFIBUS or Modbus RTU

If you want to use an operator panel with display and/or a decoupling module in the SIMOCODE pro V system with PROFIBUS or Modbus RTU, then the following configuration instructions concerning the type and number of connectable expansion modules must be observed.

The following tables show the maximum possible configuration of the expansion modules for the various combinations. These are also conveniently stored in the TIA Selection Tool. See http://www.siemens.com/tia-selection-tool.

The DM-F Local and DM-F PROFIsafe failsafe expansion modules behave in this connection like digital modules for standard applications.

Use of an operator panel with display

? Available

-- Not available

Use of a decoupling module (voltage measurement in insulated networks)

? Available

-- Not available

1) No bistable relay outputs and no more than 5 of 7 relay outputs active simultaneously (> 3 s).

Use of a decoupling module (voltage measurement in insulated networks) in combination with an operator panel with display

? Available

-- Not available

1) No bistable relay outputs and no more than 3 of 5 relay outputs active simultaneously (> 3 s).

2) No bistable relay outputs and no more than 5 of 7 relay outputs active simultaneously (> 3 s).

3) Analog module output is not used.

Protective separation

All circuits in SIMOCODE pro are safely isolated from each other in according to IEC 60947-1. That is, they are designed with double creepages and clearances. In the event of a fault, therefore, no parasitic voltages can be formed in neighboring circuits. The instructions of Test log No. 2668 must be complied with.

Types of protection EEx e and EEx d

The overload protection and the thermistor motor protection of the SIMOCODE pro system comply with the requirements for overload protection of explosion-protected motors to the type of protection:

• EEx d "flameproof enclosure" e. g. according to IEC 60079-1
• EEx e "increased safety" e. g. according to IEC 60079-7.

When using SIMOCODE pro devices with a 24 V DC control voltage, electrical separation must be ensured using a battery or a safety transformer according to IEC 61558-2-6. EC type test certificate: BVS 06 ATEX F 001 Test log: BVS PP 05.2029 EC.

Selection data for type-tested combinations/load feeders

For configuration tables according to type of coordination "1" or "2", see:

• Manual "Configuring SIRIUS", https://support.industry.siemens.com/cs/ww/en/view/40625241
• Manual "Configuring SIRIUS Innovations", https://support.industry.siemens.com/cs/ww/en/view/39714188
• System Manual “SIMOCODE pro PROFIBUS”, https://support.industry.siemens.com/cs/ww/en/view/20017780
• System Manual “SIMOCODE pro PROFINET”, https://support.industry.siemens.com/cs/ww/en/view/61896631
• Configuration Manual “SIMOCODE pro Modbus RTU”, https://support.industry.siemens.com/cs/ww/en/view/108681641

System manual

The SIMOCODE pro System Manual describes in detail the motor management system and its functions. It provides information on configuration, start-up, servicing and maintenance. A typical example of a reversing starter application is used to teach the user quickly and practically how to use the system. In addition to help on how to identify and rectify faults in the event of a malfunction, the manual also contains special information for servicing and maintenance. For selection of equipment and for planning, it is recommended to consult the system manual.

For a detailed description of the DM-F Local and DM-F PROFIsafe fail-safe expansion modules see System Manual "SIMOCODE pro Safety Fail-Safe Digital Modules", https://support.industry.siemens.com/cs/ww/en/view/50564852.

Internet

For more information, see http://www.siemens.com/simocode