SIMATIC ET 200eco . Технические данные . Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на SIMATIC ET 200eco

| | | | | | |

ET 200eco

Article number	6ES7141-3BF00-0XA0	6ES7141-3BH00-0XA0	6ES7148-3FA00-0XB0
	ET200ECO, BM141, 8DI, 24V DC	ET200ECO, BM141, 16DI, 24V DC	ET200ECO, EL-MOD., 4/8 F-DI, 24V DC
General information
Vendor identification (VendorID)	80DBh	80DAh
Supply voltage
Rated value (DC)	24 V	24 V	24 V
Reverse polarity protection	Yes	Yes	No
Input current
from supply voltage 1L+, max.	70 mA; Typical	70 mA; Typical	100 mA
Encoder supply
Number of outputs	8	8	2
Type of output voltage	24 V DC	24 V DC	min. L+ (-1.5 V)
Short-circuit protection	Yes; Electronic	Yes; Electronic	Yes
Output current
? Rated value	1 A; Aggregate current up to 55 °C	1 A; Aggregate current up to 55 °C	300 mA
Power loss
Power loss, typ.	2.4 W	3.6 W	3 W
Digital inputs
Number of digital inputs	8	16	8; 8 single channel, 4 two-channel
Input characteristic curve in accordance with IEC 61131, type 1	Yes	Yes	Yes
Number of simultaneously controllable inputs
all mounting positions
— up to 55 °C, max.	8	16	8
Input voltage
? Type of input voltage	DC	DC	DC
? Rated value (DC)	24 V	24 V	24 V
? for signal "0"	-3 to +5V	-3 to +5V	-30 to +5V
? for signal "1"	13 to 30V	13 to 30V	+15 to +30V
Input current
? for signal "1", typ.	7 mA	7 mA	3.7 mA
Input delay (for rated value of input voltage)
for standard inputs
— at "0" to "1", max.	3 ms; Typical	3 ms; Typical
— at "1" to "0", max.	3 ms; Typical	3 ms; Typical
Cable length
? unshielded, max.	30 m	30 m	30 m
Encoder
Connectable encoders
? 2-wire sensor	Yes	Yes	No
— permissible quiescent current (2-wire sensor), max.	1.5 mA	1.5 mA
Interfaces
PROFIBUS DP
? Transmission rate, max.	12 Mbit/s; 9,6 / 19,2 / 45,45 / 93,75 / 187,5 / 500 kbit/s; 1,5 / 3 / 6 / 12 Mbit/s	12 Mbit/s; 9,6 / 19,2 / 45,45 / 93,75 / 187,5 / 500 kbit/s; 1,5 / 3 / 6 / 12 Mbit/s	12 Mbit/s
Protocols
PROFIBUS DP	Yes	Yes	Yes
Interrupts/diagnostics/status information
Alarms	No	No
Diagnostic messages
? Diagnostic information readable	Yes	Yes	Yes
Diagnostics indication LED
? Group error SF (red)	Yes	Yes	Yes
? Status indicator digital input (green)	Yes	Yes	Yes
? Channel fault indicator F (red)	No	No	No
Potential separation
between PROFIBUS DP and all other circuit components	Yes	Yes	Yes
Potential separation digital inputs
? between the channels	No	No	No
Permissible potential difference
between different circuits	75 V DC/60 V AC	75 V DC/60 V AC	75 V DC/60 V AC
Isolation
Isolation tested with	500 V DC	500 V DC	500V AC for 1 minute
Degree and class of protection
IP degree of protection	IP65/67	IP65/67	IP65/67
Standards, approvals, certificates
Suitable for safety functions	No	No	Yes
Highest safety class achievable in safety mode
? acc. to EN 954			4
? Performance level according to ISO 13849-1			e
? SIL acc. to IEC 61508			SIL 2 (single-channel), SIL 3 (two-channel)
Dimensions
Width	60 mm	60 mm	60 mm
Height	210 mm	210 mm	210 mm
Depth	28 mm	28 mm	28 mm
Weights
Weight, approx.	210 g	210 g	220 g

Article number	6ES7142-3BF00-0XA0	6ES7142-3BH00-0XA0
	ET200ECO, BM142, 8DO, DC 24V/2A	ET200ECO, BM142, 16DO 24V DC/0,5A
General information
Vendor identification (VendorID)	80DDh	80FBh
Supply voltage
Rated value (DC)	24 V	24 V
Reverse polarity protection	Yes	Yes
Load voltage 2L+
? Rated value (DC)	24 V	24 V
? Reverse polarity protection	Yes	Yes
Input current
from supply voltage 1L+, max.	70 mA; Typical	70 mA; Typical
from load voltage 2L+ (without load), max.	60 mA; Typical	80 mA; Typical
Power loss
Power loss, typ.	4 W	4 W
Digital outputs
Number of digital outputs	8	16
Short-circuit protection	Yes	Yes
? Response threshold, typ.	4 A; Per channel	1.4 A; Per channel
Limitation of inductive shutdown voltage to	2L+ (-44 V)	2L+ (-47 V)
Controlling a digital input	Yes	Yes
Switching capacity of the outputs
? on lamp load, max.	10 W	5 W
Load resistance range
? lower limit	12 ?	12 ?
? upper limit	4 k?	4 k?
Output voltage
? for signal "1", min.	2L+ (-0,8 V)	2L+ (-0,8 V)
Output current
? for signal "1" rated value	2 A	0.5 A
? for signal "1" permissible range for 0 to 55 °C, min.	5 mA	5 mA
? for signal "1" permissible range for 0 to 55 °C, max.	2.4 A	1 A
? for signal "0" residual current, max.	0.5 mA	0.1 mA
Parallel switching of two outputs
? for uprating	No	No
? for redundant control of a load	Yes	Yes
Switching frequency
? with resistive load, max.	100 Hz	100 Hz
? with inductive load, max.	0.5 Hz; According to IEC 60947-5-1, DC-13	0.5 Hz; According to IEC 60947-5-1, DC-13
? on lamp load, max.	1 Hz	1 Hz
Total current of the outputs (per group)
all mounting positions
— up to 55 °C, max.	4 A; 4 A each for sockets X1, X3, X5, X7 and 4 A each for sockets X2, X4, X6, X8; note the current carrying capacity of the cable	4 A; Please note the current carrying capacity of the cable!
Cable length
? unshielded, max.	30 m	30 m
Interfaces
PROFIBUS DP
? Transmission rate, max.	12 Mbit/s; 9,6 / 19,2 / 45,45 / 93,75 / 187,5 / 500 kbit/s; 1,5 / 3 / 6 / 12 Mbit/s	12 Mbit/s; 9,6 / 19,2 / 45,45 / 93,75 / 187,5 / 500 kbit/s; 1,5 / 3 / 6 / 12 Mbit/s
Protocols
PROFIBUS DP	Yes	Yes
Interrupts/diagnostics/status information
Alarms	No	No
Diagnostic messages
? Diagnostic information readable	Yes	Yes
Diagnostics indication LED
? Group error SF (red)	Yes	Yes
? Status indicator digital output (green)	Yes	Yes
? Channel fault indicator F (red)	No	No
Potential separation
between PROFIBUS DP and all other circuit components	Yes	Yes
Potential separation digital outputs
? between the channels	No	No
Permissible potential difference
between different circuits	75 V DC/60 V AC	75 V DC/60 V AC
Isolation
Isolation tested with	500 V DC	500 V DC
Degree and class of protection
IP degree of protection	IP65/67	IP65/67
Dimensions
Width	60 mm	60 mm
Height	210 mm	210 mm
Depth	28 mm	28 mm
Weights
Weight, approx.	210 g	210 g

Article number	6ES7143-3BH00-0XA0	6ES7143-3BH10-0XA0
	ET200ECO, BM143, 8DI/DO, 2A	ET200ECO, BM143, 8DI/8DA, 1.3A
General information
Vendor identification (VendorID)	80DCh	80FCh
Supply voltage
Rated value (DC)	24 V	24 V
Reverse polarity protection	No	Yes
Load voltage 2L+
? Rated value (DC)	24 V	24 V
? Reverse polarity protection	No	Yes
Input current
from supply voltage 1L+, max.	70 mA; Typical	70 mA; Typical
from load voltage 2L+ (without load), max.	60 mA; Typical	60 mA; Typical
Encoder supply
Number of outputs	8	8
Type of output voltage	24 V DC
Short-circuit protection	Yes; Electronic	Yes; Electronic
Output current
? Rated value	0.75 A; up to 55°C max. 0.75 A (summation current)	1 A; Up to 55°C max. 1 A (summation current)
Power loss
Power loss, typ.	5 W	5 W
Digital inputs
Number of digital inputs	8	8
Input characteristic curve in accordance with IEC 61131, type 1	Yes	Yes
Number of simultaneously controllable inputs
all mounting positions
— up to 55 °C, max.	8	8
Input voltage
? Type of input voltage	DC	DC
? Rated value (DC)	24 V	24 V
? for signal "0"	-3 to +5V	-3 to +5V
? for signal "1"	13 to 30V	13 to 30V
Input current
? for signal "1", typ.	7 mA	7 mA
Input delay (for rated value of input voltage)
for standard inputs
— at "0" to "1", max.	3 ms; Typical	3 ms; Typical
— at "1" to "0", max.	3 ms; Typical	3 ms; Typical
Digital outputs
Number of digital outputs	8	8
Short-circuit protection	Yes	Yes
? Response threshold, typ.	4 A; Per channel	4 A; Per channel
Limitation of inductive shutdown voltage to	2L+ (-44 V)	2L+ (-44 V)
Controlling a digital input	Yes	Yes
Switching capacity of the outputs
? on lamp load, max.	10 W	10 W
Load resistance range
? lower limit	12 ?	12 ?
? upper limit	4 k?	4 k?
Output voltage
? for signal "1", min.	2L+ (-0,8 V)	2L+ (-1,2 V)
Output current
? for signal "1" rated value	2 A	1.3 A
? for signal "1" permissible range for 0 to 55 °C, min.	5 mA	5 mA
? for signal "1" permissible range for 0 to 55 °C, max.	2.4 A	1.8 A
? for signal "0" residual current, max.	0.5 mA	0.5 mA
Parallel switching of two outputs
? for uprating	No	No
? for redundant control of a load	Yes	Yes
Switching frequency
? with resistive load, max.	100 Hz	100 Hz
? with inductive load, max.	0.5 Hz; According to IEC 60947-5-1, DC-13	0.5 Hz; According to IEC 60947-5-1, DC-13
? on lamp load, max.	1 Hz	1 Hz
Total current of the outputs (per group)
all mounting positions
— up to 55 °C, max.	4 A; 4 A each for sockets X1, X3, X5, X7 and 4 A each for sockets X2, X4, X6, X8; note the current carrying capacity of the cable	5.2 A; Please note the current carrying capacity of the cable!
Cable length
? unshielded, max.	30 m	30 m
Encoder
Connectable encoders
? 2-wire sensor	Yes	Yes
— permissible quiescent current (2-wire sensor), max.	1.5 mA	1.5 mA
Interfaces
PROFIBUS DP
? Transmission rate, max.	12 Mbit/s; 9,6 / 19,2 / 45,45 / 93,75 / 187,5 / 500 kbit/s; 1,5 / 3 / 6 / 12 Mbit/s	12 Mbit/s; 9,6 / 19,2 / 45,45 / 93,75 / 187,5 / 500 kbit/s; 1,5 / 3 / 6 / 12 Mbit/s
Protocols
PROFIBUS DP	Yes	Yes
Interrupts/diagnostics/status information
Alarms	No	No
Diagnostic messages
? Diagnostic information readable	Yes	Yes
Diagnostics indication LED
? Group error SF (red)	Yes	Yes
? Status indicator digital input (green)	Yes	Yes
? Status indicator digital output (green)	Yes	Yes
? Channel fault indicator F (red)	No	No
Potential separation
between PROFIBUS DP and all other circuit components	Yes	Yes
Potential separation digital inputs
? between the channels	No	No
Potential separation digital outputs
? between the channels	No	No
Permissible potential difference
between different circuits	75 V DC/60 V AC	75 V DC/60 V AC
Isolation
Isolation tested with	500 V DC	500 V DC
Degree and class of protection
IP degree of protection	IP65/67	IP65/67
Dimensions
Width	60 mm	60 mm
Height	210 mm	210 mm
Depth	28 mm	28 mm
Weights
Weight, approx.	210 g	210 g

Article number	6ES7194-3AA00-0AA0	6ES7194-3AA00-0BA0
	ET200ECO, CONNECTING BLOCK ECOFAST	ET200ECO, CONNECTING BLOCK, M12, 7/8"
Power loss
Power loss, typ.	2 W; The power loss depends on the current that you loop through via the connection block.	2 W; The power loss depends on the current that you loop through via the connection block.
Dimensions
Width	79 mm	79 mm
Height	60 mm	60 mm
Depth	30 mm	29 mm
Weights
Weight, approx.	313 g	392 g

skener.ru

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
Бесконтактные выключатели Конечные выключатели Оптические датчики Энкодеры

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FS - Установка умягчения

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 23

Deprecated: Function eregi() is deprecated in /home/h101150-2/siemens71.ru/docs/kip/kip.php on line 30
SKW-FK - Установка обезжелезивания