Converters for single-quadrant operation . Технические данные. Подробное описание, цены на оборудование Siemens. Большой выбор, низкие цены на Converters for single-quadrant operation

| |

Converters for single-quadrant operation

Type of cooling
Converters ? = 125 A rated armature current: Permissible ambient air temperature during operation	Self-ventilated 0 °C to 45 °C
Converters ? = 210 A rated armature current: permissible ambient temperature during operation	Enhanced air cooling with installed fan 0 °C to 40 °C
Permissible ambient temperature during storage and transport	-25 °C to +70 °C
Installation altitude	? 1000 m above sea level (100 % load rating) > 1000 m to 5000 m above sea level
Control stability	?n = 0.006 % of the rated motor speed, valid for pulse encoder operation and digital setpoint
	?n = 0.1 % of the rated motor speed valid for analog tacho and analog setpoint ²⁾
Humidity class	Relative air humidity ? = 95 %, dewing not permissible ¹⁾
Climate class	Class 3K3 acc. to DIN IEC 60 721-3-3
Insulation	Pollution severity 2 acc. to DIN VDE 0110-1 (HD 625.1 S: 1996) dewing not permissible
Overvoltage category	Category III acc. to DIN VDE 0110-1 for power section and power supply Category II acc. to DIN VDE 0110-1 for electronics
Overvoltage resistance	Class 1 acc. to DIN VDE 0160
Degree of protection	IP00 acc. to EN 60 529
Safety class	Class I acc. to DIN VDE 0106, part 1
Shock hazard protection	Acc. to DIN VDE 0106 part 100 (VBG4) and DIN VDE 0113 part 5
RI suppression	No RI suppression acc. to EN 61 800-3
MTBF	> 200,000 h acc. to SN 29500
Mechanical rigidity	Acc. to DIN IEC 60 068-2-6
For stationary use constant amplitude:
of acceleration	0.075 mm in frequency range 10 Hz to 58 Hz
of displacement	9.8 ms -2 (1 x g) in frequency range > 9 Hz to 500 Hz
For transport constant amplitude
of displacement	3.5 mm in frequency range 5 Hz to 9 Hz
of acceleration	9.8 ms -2(1 x g) in frequency range > 9 Hz to 500 Hz
Approvals
UL/cUL ³⁾	UL-File-Nr.: E203250
Applicable standards
DIN VDE 0106 part 100	Arrangement of operator control elements in the vicinity of components/parts at hazardous voltage levels.
DIN VDE 0110 part 1	Insulation coordination for electrical equipment in low-voltage installations
EN 60 146-1-1 / DIN VDE 0558T11	Semiconductor converters General requirements and line commutated converters
EN 50178 / DIN VDE 0160	Regulations for the equipment of electrical power installatons with electronic equipment.
EN 61800-3	Variable speed drives Part 3, EMC product standard including special test procedures
EN 60068-2-6 acc. to degree of severity 12 (SN29010 part 1)	Mechanical stress

¹⁾ 75 % at 17 % annual mean
95 % at 24 °C max.

²⁾ Conditions:
The control stability (PI control) is referred to the rated motor speed and applies when the SIMOREG converter is warm. The following conditions are applicable:

Temperature changes of ±10 °K
Line voltage changes corresponding to +10 % / -5 % of the rated input voltage
Temperature coefficient of temperature-compensated tacho-generators 0.15 % per 10 °K (applies only to analog tacho-generator)
Constant setpoint (14-bit resolution)

³⁾ Not for converters with 690 V and 950 V rated voltage